digital lock on a 3000 receiver

[volki]

is the digital lock install the same on a 3000 receiver as on a 2700?

[noco7]

No it is not
go to dishlock.com to get schematics for your greybox model.

[Top40]

I tried that ...There is no such site!!!!

[Smurftoon]

There Is Such A Site!!!! You Must Have Typed In The Wrong Address!!!!

TRY:

http://www.dishlock.com/digilock1_Greybox.htm

[volki]

There Is Such A Site!!!! You Must Have Typed In The Wrong Address!!!!

TRY:

http://www.dishlock.com/digilock1_Greybox.htm
the schematic on installing the digital lock for the 3000 receiver is different that what's on my 3000 Philips receiver. the TSOP pictured has a total of 32 pins, while mine only has 28. the TSOP number is AM29F040 while mine is AD9066JR. any help would be GREATLY appreciated!

[Smurftoon]

You Must Have The Sharp Tsop. Is It Located Directly Behind The Card Slot? If You Do Have The Sharp, It Is Not Lockable. I Have Read Some Other Posts That If The Sharp Gets ECM'd, The Receiver locks Up And You Will Need To Unplug To Reset. Location ID Does Not Go To 00000001.

[volki]

the TSOP doesn't have a manufacturer name listed, has a gray box with a triangle in it. it is located in the right rear quadrant if you are looking at it from the front of the board (card slot side). the TSOP has the following numbers on it: AD9066JR
9810
C18426

i am grateful for any assistance you might have.

[Smurftoon]

Here Is One Post From Someone With A Sharp Tsop:

http://www.dssftp.com/forum/upload/showthread.php?t=9890&highlight=sharp

If You Are A member At Any Other Forums, Try Search There For Info Also.

[freq]

the schematic on installing the digital lock for the 3000 receiver is different that what's on my 3000 Philips receiver. the TSOP pictured has a total of 32 pins, while mine only has 28. the TSOP number is AM29F040 while mine is AD9066JR. any help would be GREATLY appreciated!The AD9066JR is not a Flash, that's a monolithic A/D converter. I'd guess that you are looking at the wrong side of the board!
It's probably behind the card slot area. Look for a chip with the same general number scheme as the AMD flash if you don't have one of those.

[volki]

it's not there, i checked behind the card slot area. and i am looking on the right side of the board with all the resistors, capacitors, ect.

[Smurftoon]

Your Tsop Is Located In U19 Or U26 Depending If You Have A Sharp Tsop Or AMD? They Are Located Directly Behind The Card Slot. Does It Say 3000 On The Back Of The Receiver?
Check Out The Pictures At DishLock Under Installation, DigitialLock 1.

[volki]

Smurftoon you were right.....TSOP is behind the card slot on my 3000 receiver....has the following on it: BAKER 7816 TMS29F040

can a digital lock be put on this receiver? it is able to be ECM'd right?

[freq]

it's not there, i checked behind the card slot area. and i am looking on the right side of the board with all the resistors, capacitors, ect.
I meant left to right not top to bottom when I said 'wrong side of the board'.
Of course as I said, you did find it behind the card slot, and it did have the same numbering scheme as the AMD chips. Yes, they can be ECM'd, and yes, you can install a lock. Go to the dishlock.com site as suggestd, and look at the install instructions for the Digilock 1 and 3, and look at the GreyBox or 3000 instructions.

[volki]

cool, thanks for the help.