Anyone have the flash to make HU loaders work

[xenawise]

From what I understand, the crystal is not the correct frequency in all the HU loaders and in any case most HU loaders were designed for a different purpose than to just read the card. There is no flash available to make most if any of the HU loaders read Charlie cards. Just get a ISO programmer with the 3.6864MHz crystal and the proper charlie software and all will be good...save the HU loader for....a while....

[testmoron]

wrong

[normsfirebird]

Ok a newbie who is learned a lesson. Ive paid for and downloaded several flashes and trust me when I say two weeks later just spend the 45 bucks and order from mili because there is no such flash. I have a 911 and the different H card loaders and the chip set runs on a 3.57 MHZ chip and charlie runs on a 3.68 so short of changing the chip out your not going to make a H or HU loader work with charlie. Only one site sells the chips and after shipping you may as well order from MILI he is the man Ive learned so much in the last two weeks its amazing how helpful his crew has been BIG CUDOS FOR THE MAN.

[stealtv]

I program my rom 3 with my hu loader flashed with echoboot then use echoloaders ebox to read and write :D

[srad750]

do you have the link to Dynamica?

[BirdieMod]

Yeh and you can do a p4 dump also with this. ( Joke)../.
Timing problem and I am not going to see people asking about looped card fixes from this. Thread closed.

[BirdieMod]

OK, I am informed this might work so thread opened, I have not tried any of this so all use at your own risk.

[fubr]

I program my rom 3 with my hu loader flashed with echoboot then use echoloaders ebox to read and write :D

I have echoboot but WTF is ebox?
I guess its a program yes

what the hell I might as well Play "FLASHING MY T911" too
just for shits and giggles :)

>While we are at it WTF is the 18....mhz crystal. Its not dual crystal. its not 3.68
something hardarewise has to be controlling it at 3.57, there damn sure is not any data on the web I can find about it.
I was always told that the dips set the frequency but I have never used it for charlie except with Mighty loader.

Does anybody got a good link to school someone on crystals?

[stealtv]

I found a zip at one of the many i visit called echoloader.
In the zip there are two programs and a flash.
I run winXp so i cant flash with dos, so i found xpflasher that had echoboot.
Flashed with that, then ran echoprog,CARD INFO pops and the gui screen said completed , I couldnt do anything at all so i pulled the card and closed echoprog.
There is another program in a folder called Ebox, so I tried it with the card out it says ebox connected insert card and i slid it in. The info came up. But again when I pushed any commands nothing would happen.
I figured out to pull card after each command. so with card out you push R for read card, then push card in. pop the progie starts to read and save the bin into the ebox folder.
I use nasgra edit to work on bin file, RTM to patch, then a blocker. NE saves as .bn3 so you hafe to rename the file to .bin then put in the ebox folder.
Run ebox with card out, hit L for load from file. A promt will popup asking for file name, enter the name of the file you just made, and hit enter on the keyboard.
Now slide it in, and away it goes writing the new bin to the card.
I use a Rom3 that I unlocked useing the same loader and the sn2004 software.

WinXp pro
Elvis T6
Xpflasher
echoloader.zip
rom 3
3700 softlocked tsop

[turtle57]

hi just changed my crystal in my xtreme hu loader to a 3.6864 mhz crystal is there a flash i have to use to make this work
thank,s

[fubr]

I found a zip at one of the many i visit called echoloader.
In the zip there are two programs and a flash.
I run winXp so i cant flash with dos, so i found xpflasher that had echoboot.
Flashed with that, then ran echoprog,CARD INFO pops and the gui screen said completed , I couldnt do anything at all so i pulled the card and closed echoprog.
There is another program in a folder called Ebox, so I tried it with the card out it says ebox connected insert card and i slid it in. The info came up. But again when I pushed any commands nothing would happen.
I figured out to pull card after each command. so with card out you push R for read card, then push card in. pop the progie starts to read and save the bin into the ebox folder.
I use nasgra edit to work on bin file, RTM to patch, then a blocker. NE saves as .bn3 so you hafe to rename the file to .bin then put in the ebox folder.
Run ebox with card out, hit L for load from file. A promt will popup asking for file name, enter the name of the file you just made, and hit enter on the keyboard.
Now slide it in, and away it goes writing the new bin to the card.
I use a Rom3 that I unlocked useing the same loader and the sn2004 software.

WinXp pro
Elvis T6
Xpflasher
echoloader.zip
rom 3
3700 softlocked tsop

thanks for the detailed description, I think I will put this on "backburner" and save for hard times. or should I say bored times, to much other going on right now I cant stand another obscession

[Fluffy]

Hi Guys,

I have the flash for hu loaders to do Dish Rom cards. I sent a PM to Dyna asking permission to upload it here. I'll upload it when I get Dyna's permission.

Fluffy.
P.S. Woooohooo, my first post!

P.S.S. It DOES work. I've used it and it works great!

[turtle57]

Hi Guys,

I have the flash for hu loaders to do Dish Rom cards. I sent a PM to Dyna asking permission to upload it here. I'll upload it when I get Dyna's permission.

Fluffy.
P.S. Woooohooo, my first post!

P.S.S. It DOES work. I've used it and it works great!
hi where did u get the flsh and will u post it
thank,s

[Fluffy]

Hackenum, Turtle57, BirdieMod, and all others,

I have received the PM from Dynamica. It explains that their flash is wrapped around their software utility tool, which is encrypted. You would have to buy their software program for Rom 3's & Rom 10's in order to use it.
I have cut & paste the PM below, so you could read your options that Dyna has given.

Hope this helps.

Fluffy.



Re: Your flash is wanted....do I have permission to upload?

Theres already a public flash, long long long time now... call echoboot. It wont work with nagra edit, neither will ours, its custom to certain applications. Ours is built around the echoboot but with some big diffrences and also contains encryption. Just post echoloader/echoboot flash, its been around for ages. Also SpaceTwisters V2 fash was made public by them as well. But like i said, without the application to work with it, its no good...

-Dynamica