ok here is a new one error 5 nag

[spickle]

Ok im running a atmega card with a 2700 reciver
I been aweek Or longer getting this thing programed
finally got it
I have to set clock to external in jeepers and I leave the jumper in program mode
after this thing runs awhile it then starts popping up a 05 nag
smart card not authorized to view this
nag then goes away
it might run couple hours without this nag it might run 10 minutes
Now how do I make this nag go away
I mean sheese you here have tought me so much and i really want to thank you
After all about a month ago I sat down jtagged three recivers and did a total erase on these with out backing up (i didnt know better)
all three back up and working with your help
but now on this one the stupid nag Lol
thanks

I have tried several public downloads beastrlord anglevision myatmegafix bunches of them
help me out please!!!

[spickle]

I just read a couple fuse lock settings here wich is right?
Blank screen with previews only sounds like a Rom image problem.

BUT i must say i have never heard to use those fuze/lock settings
I have alway heard to use these

If you have an 18mhz atmega
the bottom should say ff ae 89 ff
if not make sure these are selected
in column one --> select all of them
in column 2 -- > select bodlevel, sut1, cksel1, cksel2 and cksel3
in column 3 --> select ocden, eesave, and bootrst
in column 4 --> select both of them

If you have an atmega without a crystal
the bottom should say ff a0 89 ff
if not make sure these are selected
in column one --> select all of them
in column 2 -- > select bodlevel, sut1
in column 3 --> select ocden, eesave, and bootrst
in column 4 --> select both of them

If you have any other atmega then the two above
the bottom should say ff af 89 ff
if not make sure these are selected
in column one --> select all of them
in column 2 -- > select bodlevel, sut1,cksel0, cksel1, cksel2 and cksel3
in column 3 --> select ocden, eesave, and bootrst
in column 4 --> select both of them

[xklr]

I HAVE THE SIMULAR THING: BUT ITS THE RECIVER THAT SAYS (IT HAS NOT BEEN AUTHORIZED YET) :cry: undefined I'M USING A ROM3 CARD WITH A GOOD BLOCKER

[shaundeyton]

sprinkle, you the fuse lock settings listed for no crystal

[spickle]

tried all this and it is still freezing and has nag
could it be the tiers in the public download?

[funinthefalls]

Use the beastlord fix pfg in the Atmega files on dssftp.com
http://www.dssftp.com/filedownload/generate_php/dishnet_atmega_and_avr_files.php

[sfg]

I had the same problem in my 4700. It was a firmware issue. The receivers firmware was way outdated so I had to update it and now I do not get the nag at all.

So I guess I am saying make sure you have recent firmware.

sfg

[spickle]

ok you said update the firmware?
what is the firmware and how the heck you update it?
thanks

[JCK7]

IN sys info see software p231. if not / in menu 6 then 5 check do upgrade with my permissions. turn rec off with power button wait 15 min recheck see if p231 . JCK7

[spickle]

hey I have a hmmmm mofified rom2 card that is running fine in this 2700 reciver
when I put atmega in it blank screen
I can set the clock in jeepers to external and it does get channels but it freezes
now what?

[sfg]

ok you said update the firmware?
what is the firmware and how the heck you update it?
thanks

The firmware is your tsop. Do you have the machine jtagged?

If it is you can go to the tsop bank and download one with the latest firmware and compatible build code and load into your receiver. (after to change your boxkeys and receiver id in the file first)

Or you can do the stream update which I have not been able to get to work so I will be of no help with that route.

sfg