PDA

View Full Version : Error programming Flash

dallg
09-29-2004, 07:05 PM
Started JKEYS to restore full TSOP, did full Erase and when I initiate programming an Error message appears about 25% thru the operation.( Error Programming Flash at Offset Ox7FF8OOO ) Can anyone suggest a way to alleviate or correct this..What am I doing wrong???
out14w
09-29-2004, 07:11 PM
erase it about five times then try again I only had that problem one time I erased and had no further problems
dallg
09-29-2004, 07:13 PM
Started JKEYS to restore full TSOP, did full Erase and when I initiate programming an Error message appears about 25% thru the operation.( Error Programming Flash at Offset Ox7FF8OOO ) Can anyone suggest a way to alleviate or correct this..What am I doing wrong???Now I set flash for 3900 ird and can get 75% completion but at 75% I get an error message saying ( error programming at offset Ox7FFOOO2 ) How can I correct this and get a 100% completion??
dallg
09-29-2004, 07:15 PM
Out14W..will try..good idea
dallg
09-29-2004, 07:27 PM
Well my Ird took the flask OK but now Ird won't power up...anybody got any suggestions...or am I now the proud owner of another paperweight?
out14w
09-29-2004, 07:33 PM
HeHe sounds like me 2 days ago don't give up pull the card out and try to turn it on if it comes on wait for it to say insert card then just push it in don't unplug. If it isn't powering up at all take the vidmod off then try it. If that doesn't work use the voltage meter plug it in a see if it is getting power throughout the board. Oh and be sure to check your fuse. And make sure to get all the solder off the board make sure you didnt drop any on the board anywhere.
Wizkid
09-29-2004, 07:40 PM
HeHe sounds like me 2 days ago don't give up pull the card out and try to turn it on if it comes on wait for it to say insert card then just push it in don't unplug. If it isn't powering up at all take the vidmod off then try it. If that doesn't work use the voltage meter plug it in a see if it is getting power throughout the board. Oh and be sure to check your fuse. And make sure to get all the solder off the board make sure you didnt drop any on the board anywhere.


Try another computer.
dallg
09-29-2004, 07:48 PM
Hey out14W, I'm getting varios reading with volt meter..some as high as 30 some as low as 3
out14w
09-29-2004, 08:15 PM
What model reciever is it? And when was the last time it powered up and did you ground the R79 for flash or pad 1 from top or bottom?
dallg
09-29-2004, 10:03 PM
What model reciever is it? And when was the last time it powered up and did you ground the R79 for flash or pad 1 from top or bottom?
Last time it powered up was2 days ago when I got ecm'd. tried to flash but wouldn't. removed tsop lock altogether and re-attached R259 and then I was able to flash, but got errors so unplugged ird, went to bed. Got up today and no power. Yes tried both.
dallg
09-29-2004, 10:17 PM
Sorry, it's a 3900
dallg
09-30-2004, 01:31 AM
What model reciever is it? And when was the last time it powered up and did you ground the R79 for flash or pad 1 from top or bottom?R79? ain't that vid mod..no I had tsop lock removed r259 but had to put it back to get proper flash after flashed pulled plug never powered up again. No ground on pad 1 just attached pogo the way Mili sent me..Oh no what did I fuck up now......