Chinaman users

[Decal guy]

Any way to modify the disk to avoid the PPV ecm hit

[BiggerBear]

You Can Get ChinaMan At http://www.dssftp.com/filedownload/index.php
It's Number 71 in the Echostar Files section
With The Instructions Below You Can Make Your Own Dish.Bin

This is how I make my dish383.bin and it works great. It seems like alot, but after a few times it's easy. Make sure you use the latest Tier lists for MiniRTM.

How To Create The .ne3 file Using MiniRTMV2.5
Open MiniRTMV2.5
You need the latest tier list - in the same folder as MiniRTMV2.5
Choose Provider and Rom Type
Select the channels you want(make sure you select the Top AT60,AT180 & AT120)
Notice The Tiers Counter
Click - Add PPV
Click - Create Random(a bunch of times)
Under Decimal - Change the Lowest PPV ID and the Highest PPV ID
Click - Use This(bottom of screen)
Click - Create NE3 Patch
Name and Save someplace recognizable

How To Find PPV Hi’s and Low’s
Tune to a PPV channel with your receiver
On the remote hit the INFO button(not SYS INFO)
Each PPV has a 5 digit code number in prentices(55744)
Copy them and notice the Highest and Lowest.
You then round down the Lowest - If it’s 55744 round down to 55700
To get the Highest add 18000 to the Lowest ----55700 + 18000 = 73700
Some Say The Spread Should Be Less Than 2000, But I Have Been
Using A Spread Of 18000 And Have Been For A long Time.(It’s Up To You)

How To Patch To A Bin Using NagraEdit
1) Have the dish383.bin located so you can open it with NagraEdit.
2) Open NagraEdit - Click file - Open Card Image
3) Open dish383.bin - A window comes up -Card Image Type(Leave At Default)
4) Click OK
5) File Opened : dish383.bin
6) Click Tools - Open Card(remove the checkmark in front of Clean Code Space)
7) Click OK -card image cleaned successfully
8) Click Patch - Open Patch, locate your .ne3 file and Open
9) Test Patch - Bottom of screen you should see no errors detected
10) Run Patch - Patch applied with 0 errors
11) Click File - Save Card Image(name & save)
12) That Is You dish383.bin - You need to rename it by removing the .bn3
13) To rename it just right click the file and remove the .bn3(dish383.bin is what you should see until you finish)click on an open area of the page and the file name should be dish383. The .bin is hidden.
This Bin can be used it Cemu or Yvous if the INI file is directed to it.
If You Use The Bin With ChinaManDN - Just Rename It BEV381.bin

[Decal guy]

Where to get MiniRTMV2.5

[BiggerBear]

You can get MiniRTM at maestra.
Go to the File Dump-DownLoads & Uploads-Miscellaneous File,Software & Utilities
On Page1 scroll down to Tier Lists 8/3/04 by Racer88
On page2 scroll down to MiniRTM2.5 by CodFish1
To add the newer Tier List you Extract it to the folder that you put MiniRTM2.5 in

[Decal guy]

I went to maestra but could not locate the files, If you could please Private message me the links or post them here .

[BiggerBear]

Decal guy I ------- Look around --- Follow this and you will find them.

You can get MiniRTM at maestra.

Maestra - Under Dishnet

Go to the File Dump-DownLoads & Uploads-
Miscellaneous File,Software & Utilities-
On Page1 scroll down to Tier Lists 8/3/04 by Racer88
On page2 scroll down to MiniRTM2.5 by CodFish1
To add the newer Tier List you Extract it to the folder that you put MiniRTM2.5 in

[ber2z]

decal guy check your pm's . Biggerbear is right, your best bet is to make your own custom bin, it makes you far less of a target. Once you've done it, it get's easy. Just don't give up. I must have jtagged my 3100 25 times in july cause i didn't have a clue how to modify the bin.

[Decal guy]

Call me a loooooser but I cant fine them. I must be going to the wrong site. can you PM me the links or post them here. I know I am a Phuckin Looser on this one :(

[mrduffin]

I have a question that I sure the answer is obvious to some but to me it is not clear.

If everyone uses the process listed above, won't we all end up with the same results so Dish will still have the same taget for all that use it?

It seems like if we all the same tier list and tier maker, and the same PPV Hi-Lo values we will end up with the same results.

Where does the "making yur own bin" safety fit in?

I'm sure I am missing something so please don't hurt me too bad! :rolleyes:

[BiggerBear]

mrduffin -
Why not enjoy Testing and not worry about what may happen!!!
As I said in that post - You can use a tight spread, but 18000 works for me.
I can Jtag in a few minutes If I get Ecm'd, but it hasn't happened since I started making my own bins again.

[mrduffin]

I do enjoy testing so don't take me wrong. I did C-band w/ VC2 but missed the H card because C-band was still good. Did Hu and now Dish. My Rom 3 has been up for 6 days wide open so I am a happy camper.

My question was just that....a question. I will try what you said when my emu stuff arrives.

Thanks for the helpful post.

BTW.....I don't use locks either..but i can Jtag my ass off! :cool: