Wrong Cam I.D??

[trollen]

Help, I think I wrote a rom 3 cam to a rom 10 card. Now it won't let me into the card. I removed blocker, done one step clean and then started to program card. I tested patch and it said no errors so I ran patch and tried to write to card, but then it would not open card. It says bd3 log in failed. Can someone please help me. That's the only thing I can think of that I done. The cam I.D. I wrote is 009DEAEF. I don't even know where I got that from. I was using scammers. I already know I'm a fucking moron, so something positive will be much appreciated.

[trollen]

O.K., I have tried about 3 or 4 of the d2c files that I have found and everyone of them say this at the bottom after the program has ran:Run: Maximum jump (32) count exceeded, transmissions stopped; I have read a few places where other people have had the same problems but no one has helped or known the answer. Does anyone have any ideas? Thanks

[LuckLarry]

Just writing the cam i.d. shouldn't have caused this issue. Did you write more than the cam info, like a whole image???

[trollen]

Thanks for the reply, I built the program I guess you could say you know put in box keys and all that then opened patch tested and applied it. Then when I went to write image it wouldn't , that is when it started giving me the bd3 login failed error. Iv'e done this a few times that's why I don't understand what I did wrong. The cam i.d. is the only thing I could think of that I messed up. the pay per views got hit fri. night so i was going to fix it right before the Georgia Auburn game came on so I was foolishly in a hurry.

[LuckLarry]

Have you tried "Viagra"? It has a few BD error repair sequences.I have it if you need it.

[trollen]

I have tried one that is viagra rom 10 but to no avail. I have also tried some other ones like rom popper and the ones that chief recommended but cannot get any of them to work. is that the same one that you have?

[LuckLarry]

The one I have has 4 repair sequences in it, one of them being BD3 repair. Not sure what you have???

[trollen]

hey that sounds great. the one i have doesn't, could you give me that one sir?

[LuckLarry]

hey that sounds great. the one i have doesn't, could you give me that one sir?
P.M. your addy to me...

[trollen]

hey i got it thanks. I will try it and get back to you.

[LuckLarry]

Cool...I have fixed one of two BD failures with this.

[trollen]

Well I tried it. But I couldn't get it to work. I think i did all the steps right. Thanks though. I will keep trying every thing again and search for some new stuff.

[LuckLarry]

Kee- trying, bro. Do you have access to another ISO/puter combo to try?

[sukh77]

As I was reading it seems like you didn't even get a successfull write to the card, so there is no way u fucked it up. Unless we are missing a step somewhere. You have to just try one of your old passwords on it. your first post says you did a one step clean but then your 3rd post you say it didn't even write.

[trollen]

Sukh77
Yeah, see the first post was right after I f'd up and about 10 minutes before the Ga game came on, so I was a little stressed. The 3rd post was correct. Because after I ran the patch, I tried to write to card and it reported the error. And I have done everything wrong on this deal because I got this card through a trade and did not even make a back up image of the card. And to boot it is the only programmable card I currently have. So I wouldn't have a clue as to what password to start with. I've tried the basic ones. I have fought with the viagra that LuckLarry has been helping me with, but now I have a question about that because maybe I am doing something wrong. In the readme of viagra where it says after you have ran the commads to write a good virgin bin to the card, what exactly does that mean? how exactly are you supposed to write it. Do you use nagra? Then where it says once you dump your card make sure you load a clean bin of your choice and make sure the bdo-3 are all set. Can you tell me exactly what that means. Thanks for helping a boot.

[uncletodd2000]

I am still trying to recover from a hit on my rom 10,s. was told i had bad cam id but really don,t know. can anyone pm me a good rom10 image w valid cam id for testing.
Thank You

[sukh77]

trollen it seems you are pretty much out of luck. You might need to send to get it unlocked. There is a very trusted user here that can probably unlock it fo you. do a search on unlock hope fully you will find him\her. oNe other program you can try is mrom try to get version5 if possible, I believe it is in the files section. let me know if you don't find it or the user.

uncletodd - I recommend you download a program called numax creator it is a 2 part download in the echostar files section. It is very easy to use, once you do the setup. let me know if you have any problems with it.

[uncletodd2000]

trollen it seems you are pretty much out of luck. You might need to send to get it unlocked. There is a very trusted user here that can probably unlock it fo you. do a search on unlock hope fully you will find him\her. oNe other program you can try is mrom try to get version5 if possible, I believe it is in the files section. let me know if you don't find it or the user.

uncletodd - I recommend you download a program called numax creator it is a 2 part download in the echostar files section. It is very easy to use, once you do the setup. let me know if you have any problems with it.


i am getting an error message when trying to update numax creator 3.0. "active x component can't create object" then the download stalls permanently. whut am i doing wrong? sorry i realize this is probably a puter problem but help please.
Thanks- uncletodd

[sukh77]

No not a computer problem. Don't worry about the update everything is pretty much up to date. If you have any other problem Let me know.

[uncletodd2000]

I think i have correctly figured out the program and used on a rom 10. have problems though. screen freezes up and system reboots after few minutes of airtime. i have downloade freeze fix from forums but do not know how to apply.
program still not updating.

How do i solve freezing problem?

Thanks,
sancho

[sukh77]

Did you apply a blocker seperate or did you use the one that numax includes?
I'm not aware of a freeze fix. It's probably a different blocker or someone's image. I recommend you don't use this you might screw up your card. What IRD do you have? Is it up to date firmware?

[uncletodd2000]

i have used numax blocker and also unlocked and used checksum blocker. i think both are same thing but same result either way. freezing and reboot.

i have 7200 ird with simple lock, rom 10. the freeze fix is located in download section right on top of two part download in echosar files. i am unsure of firmware update. will unlock and boot up to check same but is current as of last ecm.

[sukh77]

Maybe the 7200 is having a problem then. It's not happening on anything else. Definately not on a 301. Maybe someone else can help. Numax uses the checksum blocker. Might try different blocker. Do a search on what's working right now. Might want to pay mili for private blocker.