PDA

View Full Version : Warning 061

CountryBoy
02-02-2005, 12:51 AM
i hvae just recently put up a new dishnetwork dish...and i have got the satelite singanl aquired..but i keep getting a warning...the is say... do not disturb or unplug the reciever...ydda yadda...so i wanna know to to fix this small problem...iam i going to have to redo the T sop?..? thanks for all the help!!
Raddude
02-02-2005, 04:40 AM
What model IRD do you have and does it have a TSOP/EEPROM lock ? The firmware version should be updated. So far, I have heard of no problems by letting updates in. Check this to see what version you should be at. http://www.dishnetwork.com/content/customerCare/technical/software_versions/index.asp Unlock and turn off thr IRD and it should download immediatly. Don't forget to relock right away!
Crazy1_79
02-02-2005, 04:45 AM
let it take the update, might take 30 minuts, usually just 5 minuts, then you will be at current rev and good to go. test on
BirdieMod
02-02-2005, 08:19 AM
Yep, 061 is virgin firmware stream updating to current, Don't see that usually on ecm fixes and such, But it's normal.
CountryBoy
02-02-2005, 08:32 PM
so is the easiest wat to solve this promble is the erase sa5..2700 receiver..and then let it restream and get the updates with the lock off and no card in..?
BirdieMod
02-02-2005, 09:07 PM
Just put the card in and let it complete the 061 update. On remote press "Menu,6,1,1" run check switch, If it looks good hit cancel, It will ask if signal and aiming is good/Signal locked, Answer yes, Then let it go to 061 updating, After you are all set.
If you didn't yet, Save the virgin tsop image, It could be handy later.
BirdieMod
02-02-2005, 09:09 PM
Make sure you have a blocker on the card, If it's virgin also the ird and boxkeys on the card will be all zero's yet and probably will not stream lock, But never hurts to play it safe anyway.
CountryBoy
02-02-2005, 09:51 PM
i have left the receiver siting for ever..and when i run the check switch test...nothin..everything is XXX out...so should i erase the sa5 and then start over?
BirdieMod
02-02-2005, 10:03 PM
If it is not passing check switch it will not update either by dumping SA5. You need signal for either way to work. Is the dish aimed correctly and is it non DP series?
CountryBoy
02-02-2005, 10:13 PM
well when i go into aim dish..i have it locked on 119, its only at 60 but it says locked..? so any ideas? why it would say that?
BirdieMod
02-02-2005, 10:17 PM
60 is a pretty weak signal. What is your dish setup? Dish and switch connected models/ type?
CountryBoy
02-02-2005, 10:25 PM
dish---cord to reciever---reciever to tv---receiver 2700
BirdieMod
02-02-2005, 10:36 PM
Not quite what I meant here.....
The dish itself, Is it a 18 inch round, 20 inch oval, 1 LNB 2 LNB's? Does the dish have a "DP" logo on its lnb/feedhorn assembly?
CountryBoy
02-02-2005, 10:38 PM
oh..haha, 18 inch, 1 lnb, with two outputs, and the dish says bell express vu on it
BirdieMod
02-02-2005, 10:44 PM
OK, That would be the same as a dish 300 setup then, It doesn't have a switch so it will not pass on the check switch test, It should say "No switch detected".
Try going into dish setup signal meter and set it to transponder 11, I'd try getting the signal up a little higher. Then if you haven't yet, Jtag it and do a "Save Mem" so you have a tsop backup. Then dump sa5 and let it restream.
CountryBoy
02-02-2005, 10:49 PM
k great! thats what i was going to try tongiht. thanks a bunch!!!
lefty3m
02-03-2005, 07:46 AM
I've been trying to get a Model 3800 to update in the stream also. I'm wondering if Charley has killed the stream update for more models. I've done this hundreds of times in the past and never had a problem.
I would suggest everyone make a backup of their tsop, maybe something new is brewing.