2 channels after ECM repair

[Soapstreet]

I only have channels 101 and 103 after I sector erased SA5 on my 2700 receiver. It was on channel 103 all night. So it had to have updated by now. I had to reprogram the card. But it works fine in my 301, but when I changed the Box keys, receiver #, etc for it to work in the 2700, I only get 2 channels.

What gives???

Thanks.

[Chief]

Most likely, your erase procedure failed. Check your LOC ID again; bet it's 0000001. This happens more often than you think.

When you restream it, leave it OFF with the card OUT.

[rubberman]

happened to me many times even though i erased SA30 5 times.

[Jessica]

Do a switch check,,,,,,

Jessica :)

[rubberman]

that wont matter.

[BirdieMod]

If it had video right after deleting your sa sector, It did not delete it, SHould have had a black screen until it restreamed and updated.

[Soapstreet]

OK, I cleared it about 10 times but it is still coming up 0000001 on the location ID. I Pulled the card. Did the sector erase on SA5 with the card out and when I got finished, it popped up on the screen still saying that the location ID is 0000001.


Will the 0000001 clear after the receiver updates? Or will it show immediatley after the repair?

Thanks.

[mrmark28]

ive got a 2700 with same black screen problem my location id is good and i even tried to erase the full tsop and program back in the original saved tsop my problem this ird has been out of the stream for a while it even came with a rom3 rev372. so could it be somthing with the update stream? ive done 3 other 2800 irs in the last day with no problem its just this 2700 that wont buge. also have done the check switch and sa5 ersae

[Chief]

Soapstreet, you must restream the receiver and allow it to rewrite the sector you just erased. Leave the card out, plug in the sat feed and the receiver power. Don't manually turn the receiver on.

The green power light should flicker, go off/on/off/on....after a few minutes, it may go off and stay off, or show the sys info screen. At that time, the rewriting is finished. Don't interrupt the process, or you'll be right back at 0000001.

MrMark28, check your card's data to make sure it's being programmed with the current public decrypt keys.

Key 0 06 07 F0 E2 61 6F E1 45
Key 1 01 C5 FB 21 37 B6 C0 5E

[jake112]

Soapstreet, you must restream the receiver and allow it to rewrite the sector you just erased. Leave the card out, plug in the sat feed and the receiver power. Don't manually turn the receiver on.

The green power light should flicker, go off/on/off/on....after a few minutes, it may go off and stay off, or show the sys info screen. At that time, the rewriting is finished. Don't interrupt the process, or you'll be right back at 0000001.

MrMark28, check your card's data to make sure it's being programmed with the current public decrypt keys.

Key 0 06 07 F0 E2 61 6F E1 45
Key 1 01 C5 FB 21 37 B6 C0 5E


i have the same issues with two 301.10's erased both boxes numerous times and put the patched tsop on.... but when I plug in the boxes without the cards they dont restream... just comes up with the sytem info............ can both tsops be bad????

[mrmark28]

thanks chief i have solved my problem when i did a read from the card it gave me boxkeys that was off 1 letter from the read i got from jkeys didnt catch it at first..now this is the second time this has happened??? i even double checked the card image i save right from the start at thats what it said strange.. but im up and running now thanks again word to the wise check and check and check again all those important numbers :cool:

[Crazy1_79]

Do a switch check,,,,,,

Jessica :)
Damn jessica, are those your boobies?