not getting good mixture of --'s ++'s

[haris5060]

i have nexus moded t911 and have rom 10 trying to get good mixture with d9 flashed in loader tried raising and lower by 5 , 10 15 still unable to get doo mixture I either get !!!!! or !!! XXXXX or -----!!!---------------!!!
Anyone can help me plzzzz:(

[Cid6.7]

Try D7/8 flashes aswell

[haris5060]

still no ++++ only ----- or -----!!!! or xxx---!!!!!!

[Cid6.7]

how low do you have the limit..?

[Cimba]

Hi Cid, want a good well looped rom 3 card cheap ???? lol

[haris5060]

30&10
and went up 5 also 10 also 15

[Cimba]

Cid, came across a new program called Dishunlooper with RevolutionX flash. Heard of it ? No explanation with it, loaded it and seems to run but I don't know if you need a special loader or not.

[haris5060]

Const VAVCCTestMax = &h18 '<--- Set this to the MAXIMUM VCC to test the card with.
Const VAVCCTestMin = &h10

getting only--------------------------------

[Cid6.7]

Const VAVCCTestMax = &h18 '<--- Set this to the MAXIMUM VCC to test the card with.
Const VAVCCTestMin = &h10

getting only--------------------------------

Raise the Max up a bit try 2 increments @ a time if it starts to get resets try adjusting your pot a bit aswell
Yah Cimba I have it..hasent done squat..
you can send it to me if you want I can give it a whirl & send it back if I unloop it..We're moving back to BC in Aughust it might take me untill then to unloop it..lol

[haris5060]

if i go 18 and 10 i get only -----------------
if i go 99 90 i get only !!!!!!!!!!!!!!!!!!!!!!!!!!!!!

[Cid6.7]

go from 18 to 20 to 22 to 24 & keep going untill you get some ++++++++'s leave your floor setting the same..

[haris5060]

wen to 30 and 10 started to get this
& 2_1.rar\VCC Analyzer v2.xvb
TX Data : 02 03 00
TX Data : 02 02 00
TX Data : 07 0E 03 10 01 03 9A 00
RX Data : 07 1B
RX Data : 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50
30 31 30 20 52 65 76 41 32
TX Data : 12 15 AB 21 00 08 A0 CA 00 00 02 12 00 06 55 0E
03 8B 00
RX Data : 12 0C
RX Data : 12 00 08 92 04 01

VCC 30: ----!!----!!--!!!!----!!!!--!!!!--!!--------!!!!!!------------!!------!!!!-------------------------- 6F = 0% FF = 70%
VCC 2F: !!--!!------!!!!------------------!!----!!----------------------!!----------!!------!!----------------------------------------!!-- 6F = 0% FF = 88%
VCC 2D: ---------------------------------------------------------------------------------------------------- 6F = 0% FF = 100%

VCC Ceiling: 33
VCC Floor..: 2D

[haris5060]

Rom 10 A21 finally poped
using rom poper here is what I did I was getting error when runnning script rompoperv33. "saying error rest failed" <<<<<<,this was due to the fact that i was using COM 2 and the script is setup for COM! so all you ppl out thier doub;e click the script and click on the seach when script is open click FIND type COM .
when it finds the COM 1 change it to whatevr your are using ie com1 ,2 or whatever if you dont find it and it picks on communication just click search and NEXT ..........
Also MAke sure You are using un moded loadder such as just a ISO PROGRAMMER.
Thanks alot to my dear friend CID6.7................ He is a very good friend always helping me out
:) :) :)

[Crazy1_79]

Yes, it was a A21 the reason for the !!!! is because the 83 response was being detected by the loader at all glitch attemps, any !! that you seen would have been a ++ if it was in fact a rev A23. you cannot use a modded loader to open A21's I always used Sorry Nagra with a standard loader because it will not mark the card,

[haris5060]

so is my card marked now and if it is what will happened and if its not how fdo i tell