odd Rom3 unlocking

[VirgoVixen]

I just wanted to share this info. I had a rom3 that I have been running powerunlockverall2 on for the past 9 hours. I used d9 flash and got a good mix of +++++------ in powerunlock using vccstart=2a and vcclimit=20. To get a good combo of the +++++------, while card was running script I moved my trimmer up and down till I got just the right mix, then I got my ceiling and floor. I noticed my loader does not do well with ohms 2.2 it seems to work best around .25 and .35. I also notice each card is different as far as the ohms. Anyway I flashed to d6-1 and put in my ceiling and floor as Crazy1 explains. I just left it alone, 9 hours later I got this

o6Fo6Fo6Fo6Fo6Fo6Fo6Fo6Fo6Fo6Fo6Fo6Fo6Fo6Fo6Fo6Fo6 Fo6Fo6Fo6Fo6Fo6Fo6Fo00o00o00o00o00o00o00o00--- try to hit 0C bug at 10A2
o00o00o00o00o00o00o00o00o00o00o00o00o00o00o00o00o0 0o00o00o00o00o00o00o00o00o00o00o00o00o00o00--- try to hit 0C bug at 10A3
o00o00o00o00o00o00o00o00o00o00o00o00o00o00o00o00o0 0o00o00o00o00o00o00o00o00o00o00o00o00o00o00--- try to hit 0C bug at 10A4
o00o00o00o00o00o00o00o00o00o00o00o00o00o63
=========================
= CAM IS OPEN NOW !!!!! =
=========================

Card is now open and good to go. This way of opening rom3's is not an exact science, but so far I have opened 5 rom3's, 4 of which went pretty quick, less than half an hour. I have not messed with delays any. I did try to mess with the delay settings, but it confuses me so I just mess with the trimmer to get good combo. It could be because I have a kickass loader that Crazy1 modded for me and he did an exceptionally good job. Or I might be doing something different than what I have read. I just noticed everyone saying to not mess with the trimmer for the most part and to keep it at one ohm setting, but mess with delays. I have not messed with delays just my ohms. Also when I analyze a rom 3 with the d9 flash, I go straight to d6-1 flash and start unlocking procedure. This info may or may not help anyone, but is working good for me.

.

[Cid6.7]

I had 3 383's with kinda the same results a couple days ago they all looped ..lol
I let them run for a bit with some o001o004o002 etc & they all unlooped & unlocked aswell.

[Crazy1_79]

I have some stubborn ass rom 3's I am working on, I think the pot went out of my loader, it was still working well enough to pop 10's but rom 3's are touchier, at least for me they are. I could check my resistance at the pot and the ohms would jump 10 ohms or so and then slowly come back down to where it was, then it would drop 10 or so more and come back, acting very squirelly. so I got a new pot and am trying the rom 3's again, will post if I get them open.

[VirgoVixen]

Cid are you sure they looped? I noticed when I try to read any card without a restart after unlocking, and going straight to my iso and nagra I get atr string bad. But after a restart am able to do one step clean and program card. You probably know this and tried that I am sure, thought I would mention it anyway :).