Rom 11 B8A Glitched Up !

[beercan22]

Hey, Y'all! Trying to bust open a stream locked Rom 11 @ B8A using Powersyncunlockall V3. Been running for two days now and never get past the glitch test. Maybe I'm doing this wrong. When the script starts I try to get the best balance of + and - I can by adjusting the pot......then it starts its routine and runs for ever trying different combinations of VCC, Delay, etc. Then it will get a script error and timeout. I tried the "edited" version too and get the same results. I know the VCC settings are automatic now but what the hell is this "glitch test" program trying to do??? I never see any 6's or F's !! Any help would sure be appreciated and Happy Friday !!
Beercan :)

[Crazy1_79]

it is trying to isolate the best vcc glitch points for your card. it will then automatically insert those into the script and try to open it. I do not know why it is timing out, I have never tried a rom 11

[skinerd]

Mine does as described above also. It also requires me to reflash the Amtel, after every timeout, to continue.
So far I have not opened a ROM 11, several 10's and 3's but not this 1 ROM 11......

[beercan22]

It seems that the "Edited" version of the powersync program runs a little better (no more timeouts!) but it never gets to the poppin' mode (sixes and Fs). Is there a way to go straight to the part of the script that tries to pop the card?? I ran this script for two days! Checked the card and it is not looped. Tried adjusting the pot a bunch of times too with no affect. Has anyone really popped one of these guys yet and what did you use and what were your settings???
Thanks,
Beercan :)

[beercan22]

Mine does as described above also. It also requires me to reflash the Amtel, after every timeout, to continue.
So far I have not opened a ROM 11, several 10's and 3's but not this 1 ROM 11......

Skinerd,
When it times out.........unplug the T911 and plug it back in again. Seems to reset it.
Beercan :)

[Cid6.7]

I popped a R11 B8A useing D11 & Powersyncver3 Its the 1st time useing Powersync on a rom11 Toy's rom11 script looped every rom11 I ran through it guess it doesnt like my loader..


*********** we hit our bug *************
9000 was our loggin = good loggin, D7 packet 2 wrote to cam
1240029000
===========================================
90 was hit at 1712 delay ----VCC WAS 15 , our GlitchType was 07

TX Data : 07 0E 03 10 01 03 9A 00
RX Data : 07 1B
RX Data : 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50
30 31 31 20 52 65 76 42 38
TX Data : 60 15 F6 21 40
TX Data : 53 A0 CA 00 00 4D 00 4B 00 01 02 28 E2 FE EF 6F
TX Data : E0 1A 8D EE 21 88 E4 9E 9D 76 AA 32 AE 1D 1E 6F
TX Data : 34 B6 6C F4 72 81 9A 65 D3 80 8A F6 B5 B1 E3 04
TX Data : 39 30 C4 A7 45 4B 67 7F 7D B2 24 E1 A6 ED 30 1E
TX Data : 9F 48 1C 93 14 AB FD 1D FC 90 FF 74 E2 43 BF 2D
TX Data : 27 63 7E 05 37 20 00 FF 0E 05 85 00
RX Data : 60 06
RX Data : 12 00 07 80 03

********************************
* DISH ROM11 B8A EMM sent *
* ROM11 B8A cam should be open *
* test in Nagra to see. *
* if not, try again. *
********************************

[beercan22]

Just give it LOTS of time. It took two days, on and off, but it works!
Beercan :)

[apbarn]

What Script Were You Useing,and Any Other Help Would Be Appreceiated

[beercan22]

What Script Were You Useing,and Any Other Help Would Be Appreceiated

The Powersync V3 script. Used default settings. Make sure "logging" is off!
Beercan :)

[apbarn]

were can i find this script

[apbarn]

Thanks Will Post Results

[apbarn]

were do you turn,logging is off,cannot find setting.is it in the script or in win explorer

[apbarn]

what were your win explorer settings at

[beercan22]

what were your win explorer settings at

All the info is in the "Moded loader how to guide" stickey above. Options are in Winex. :)