PDA

View Full Version : Pot Adjustment Question For T911

crenaud
03-04-2005, 08:40 PM
The pot on my loader only goes as far as 2k resistance. Is this normal or do I have a problem with my mod?
Cid6.7
03-04-2005, 08:57 PM
thats fine its prolly a 2k pot
crenaud
03-04-2005, 10:27 PM
actually it is a 5k pot from rat shack that's why I was wondering.
Crazy1_79
03-05-2005, 03:41 PM
then it shold go to 5K, it is a problem with the pot not the mod, do you have your ohm meter set higher that 2K?
haris5060
03-05-2005, 05:16 PM
i had same problem and i put it 2.2k and threw that crappy pot
ROTTEN
03-05-2005, 05:24 PM
are you checking pot with power off?
krameel
03-08-2005, 09:27 PM
Set pot at 1.9k and you should be fine. Work well for me all the time.
Cimba
03-08-2005, 10:07 PM
then it should go to 5K, it is a problem with the pot not the mod, do you have your ohm meter set higher that 2K?

On your meter set the pointer to the 20k setting, that is higher than 5k and should give you a proper read as Crazy says.
seanvan
03-09-2005, 06:53 AM
i need someone to help me to unlock room 3 i arn running the test file they always give me the error mesage. what do i do when i get the message below?


Executing Script: C:\Documents and Settings\seanvan\Local Settings\Temp\Temporary Directory 3 for rom3unlocker-glitcher2 rev383 penga69 unlocker.zip\3-TESTFILES\TESTglitchFIND.XVB
TX Data : A0
TX Data : A1
TX Data : 07 0E 03 10 01 03 9A 00
RX Data : 07 1B
RX Data : 3F FF 95 00 FF 91 81 71 64 47 00 44 4E 41 53 50
30 30 33 20 52 65 76 33 38
OVERFLOW WAS SENT TO 00 E050, READ CAM LATER WITH NAGRA EDIT TO SEE E050
CHANGED FROM FF TO 00. IF IT DID WE KNOW OVERFLOW IS WORKING.

===========================================
VCC = 22-0710A4 GLITCHED past 0C BUG
3FFF9500
===========================================

Script Error on Line 152
Sc.GetByte: Requested Byte Exceeds Last Read Request
Cimba
03-09-2005, 08:22 AM
Read Crazy's Sticky on using modded loaders.
Read Cid's post on unlocking rom 3's.

Well according to your analyzer message your VCC= 22 and Delay = 10A4.
A) Did you set your WinEx 5.0 to the needed settings for running a modded loader
B) What type of loader do you have and what type of flash did you put on it ?
1) Is this a streamlocked card @ 383 ?
2) If not you should be using penga's unlockrom3.xvb program
3) Whichever unlocking program you use, set your VCC to 23 and 1A and delays to 10A4 to 10A5 to start and let it run.
seanvan
03-09-2005, 04:59 PM
Yes, my card is extreme 383. The below note were what my setting with WinExp 5.0 I even let it ran all night still nothing is working. Please review and advise.
and i buy 911modded loaders fom dsshouse.com


com= pick your port
data baud=115200
reset baud=115200
parity =none
rec timout=1000
byte delay=100
reset delay=100
stopbits =1
byte convention= direct
flush echo bytes= no check
flush receive buffer= check

===========================
advanced tab

check device reset(no atr)
no check ignore receive timout
dtr= low
rts= high
toggle line =rts

save you settings to loader2
make sure it is set to these settings.
seanvan
03-09-2005, 05:02 PM
and i buy 911modded loaders fom dsshouse.com