Moded my terminator typhoon, works.

[rehash]

I poped 4 rom 10 cards in about 2 hours useing A23uV1 in the rom10&3 package. I'm still having trouble with rom 3's anybody know where I can find unlockrom3xvb? thanks

[Cid6.7]

here it is
If your having probs read my rom3 guide

[rehash]

Thanks I read your how to but I did'nt have the progy. Between you & Crazy1-79 I figured it out sure needed the help, thanks a lot.

[BLADE2061]

Hey Can You Help Me .. I Have A T5 Typhoon.. I Need To Know How To Mod It ... Any Pics Or Directions On How To Do It? Thanx

[rehash]

Sorry I didn't answer your PM I read it but my puter burped & lost it. Go to cardcoders. org search under terminator typhoon there is web site listed with excellent pictures & data. I did change one thing, used 2.2k resistor instead of pot. See ya. PM me if you need more.

[Nefarious]

I cant seem to find that info for the typhoon mod on their site

Can you post a direct link please or upload the info?

Thanks

[BLADE2061]

Me Either It's Not There .. Guess I'm Blind Can U Post Link Please

[rehash]

I cant seem to find that info for the typhoon mod on their site

Can you post a direct link please or upload the info?

Thanks
Go to WWW.icwell.com/images/ good luck

[Nefarious]

Thanks, I'll give it a try

[2769]

i need to know where to buy a moded loader from i bought one from dsshouse was a piece of junk any one know where else to buy from . thanks

[Nefarious]

DOH! Mine is a T5 Typhoon-2 REV.2, its a dit different on the back.

What is pic 2 showing? I dont see any mods in it

[Nefarious]

Hers a few picts of mine. Its a little different that the other picts. If I could see the full images in the other picts I could prob make the connections. Has anyone done one of these or maybe know how to?

[Nefarious]

Bump!

Anyone? ? Beuller?

[rehash]

DOH! Mine is a T5 Typhoon-2 REV.2, its a dit different on the back.

What is pic 2 showing? I dont see any mods in it
Pic. 2 shpws that on chip # 74HC00 you must cut the trace between 1 & 2and between 2& 4 [in front of 3 ]. Also lift or cut off leg #1 [ I cut it off ]. Also I used a 2.2k resistor instead of a pot. I have lost the how to that came with these pic's, look at # 3 the wire that goes over the side goes to the leg you lifted on 74CH00. And the 2 blue dots are for the switch.


Any thing I can do, hollar Rehash

[Nefarious]

thanks, I'll give it a try

[Nefarious]

Bump!

Never did get this one working....

Has anyone seen a ver 2 like this before?

[BigVWman]

Never seen a ver 2 but the chip layout is the same as my terminator typhoon 5 switch. If you use the generic guide you could meter it out and get it to work. Also clockspeed has some simplified directions(for typhoon) over at Rom10x. Modded mine and its working touchy on the adjustment of the pot but popped several in under 2 minutes each after some tweaking.

[BLADE2061]

anybody got this loader it is supposed to be a t5 terminator typhoon, i need help modding>>> it anybody done this one before?

[BigVWman]

anybody got this loader it is supposed to be a t5 terminator typhoon, i need help modding>>> it anybody done this one before?
yep and it is a t5 terminator/typhoon 5 switch.

Clockspeed...'s Notes To Mod A T-5 Terminator Typhoon 5 Dipswitch Model:


This model of T5 has four surface mt chips on the reverse side, 2 74hc74's(u4 unused here, u10 this one we mod) and 2 74hc42 (u5 unused, u9 unused). The top side of the board has all dip mounted chips, the atmel is socketed. All of the semiconductors are labelled on the board.

I included a stock pinout for a 74hc00, which is missing from the full "Guide to Mod Any Unlooper", included on the picture are the stock hookups to the chip. I also included pics of my modded unlooper (Messy huh?!?)

I cut the trace running from pin #9 of the 74hc74 (u10) to pin #12 of the 74hc00.

I cut the trace between the max232-pin10 (u6) and atmel-pin18 (u8).

I cut the trace between the jumper block and pin#9 of the 74hc00 (u2)


On the 74hc00n (u2) i cut pin 1 bent it up and connected it (pin #1) to atmel pin #14...

pin#2 (74hc00) to jumper block (to the 4 pins connected by 1 trace under jumperblock, on the reverse side)...

pin #3 (74hc00) to atmel pin 6...

pin #9 (74hc00) to pin 9 74hc74 (u10) (surface mount on reverse side) pin 9 trace .

pin #12 (74hc00) to atmel #18.


there were traces between pins 2-3-4 that need to be cut as the unused gates on 74hc00 (pins 1-2-3) are tied to either vcc or ground and this needs to be remedied. this is why i cut pin 1, and bent it up, as it was tied to (vcc?) and cutting the trace wouldnt work... I cut the traces between 2-3-4, but you could just as easily cut pin 2 and 3 and hook directly to the pins, instead of trying to cut the traces, its tough! Use a meter to check your cuts!

5K Pot from pin 4, 74hc4053 (u11) to ground.

All of the traces were cut by following theabove article using a multimeter. The 74hc00 pinout below really helps you follow the article...

I run it at 6v with my variable voltage power supply.

I was unable to flash the 2313 in the unlooper, even with the jumper wire, i had to use a simple programmer, in dos...

Works good, have opened a24, a81, rom11, etc...

...clockspeed...

all credit for above goes to Clockspeed and CC it is a C&P but it really helps. I substituted a 1k 15 turn pot since most people seem to be hitting a sweet spot under 1k and the 15 turn gives you a more precise control to fine tune. when your done double check all with meter and head for winex with loader2 settings fine tune pot and your off and running. good luck i hit most with the delay set around 320.

[BLADE2061]

hey thanks, going to give it a try

[BLADE2061]

hey can you direct me to the pics of this mod
Thanks

[Nefarious]

Yes! Please post any picts you may have.

Thanks

[Nefarious]

or if you want, just draw the mods in paintshop on these images of my t5

[BLADE2061]

yeah i need a pic i dont want to cut the wrong pin/trace on my loader that would really suck..

[boricua]

i have theasame t5 typhoon help how to cut and needpicture thank you

[Nefarious]

well, I checked out the instructions and they seem to be accurate as far as pin to pin. Even though the rev2 is laid out slightly different it still has the same chips and therefore the same traces. I used a tone tester and found each connection listed. I think I'm going to give it a shot since the loader isn't of much value to me anymore as it is.

I'm a little leery about lifting pins from a hole though connection because Ive broken them before so I pulled out the 74hc00 and socketed it. Bending the pin while the chip is out seems easier.

My only question is about
On the 74hc00n (u2) i cut pin 1 bent it up and connected it (pin #1) to atmel pin #14...

pin#2 (74hc00) to jumper block (to the 4 pins connected by 1 trace under jumperblock, on the reverse side)...

pin #3 (74hc00) to atmel pin 6...

pin #9 (74hc00) to pin 9 74hc74 (u10) (surface mount on reverse side) pin 9 trace .

pin #12 (74hc00) to atmel #18.

With pins 2,3,9,12 should those be lifted from the board as well?

[BigVWman]

Nope you don't have to worry about lifting any other pins, just cut traces in the instructions and you will be a-ok. I actually didn't lift the pin 1 either i used a very small dremel tip to cut it at the board then that left enough so that i could solder on. everyone is looking for pictures and that is a bad idea since the quality won't allow you to accurately see which traces are cut and soldered to that is why i said to use your meter. Just do one step at a time double check it reread it and meter it before and after you'll do just fine!!

[Nefarious]

well I should have some time over the holliday to give this a try.

Does the mod render your jumpers useless? Do you even need them any more?

How did you calibrate your POT to find the glitch? Is there a program to help you do this or is it trial and error?

[Nefarious]

about done witht he mod but I'm not getting a glitch. The instructions say
5K Pot from pin 4, 74hc4053 (u11) to ground.

but isint pin 9 the vcc?

[Nefarious]

well, NM, Looks like I got one!

Let the 102 Glitching continue....
LETS TRY NEW DELAY
Glitch Delay = 0337
VCC = 0F

--+---+---+---+---+---+---+---+---+--
TX Data : A1
===========================================
Glitch Success!! A0FF-INTERCEPT IS ON
BootLoader 6F 00 RSP Received!!
VCC = 03 (~5.88235294117647E-02 vdc)
Glitch Delay = 0337
Glitch type 06
===========================================
Card dumped in n2e b7 ok
I'll continue to work and see if I can get something going

Ill post picts and info soon for the rest of you t5 users

[BigVWman]

Congrats! I never posted pics because i felt people should meter theirs out since it seems some t5's have different traces. you cannot go wrong metering each mod but if your not thinking and only looking at a picture you'll likely have a problem.

[Nefarious]

Thanks, I hope most are smart enough to just use the picts to help. I put up the info on the finshed product.

http://www.dssftp.com/forum/showthread.php?p=332163#post332163

thanks all!

[BLADE2061]

mine is a bit different where yours says T5 Typhoon-2 Rev.2 mine says Terminator T5 Board i posted pics on back in this topic here http://www.dssftp.com/forum/showthread.php?t=41631

if anyone knows where i can find a mod of this loader please post i need help.. there are so many different versions of this T5, not sure which mod to follow to get mine a going..

[Nefarious]

wow, those picts make my eyes hurt :-) is it still in the plastic case?

Is it a rev.2? Regardless its a typhoon so it should have all the same chips the just may be in different locations. The will still have the same traces to make them work. Read http://www.dssftp.com/forum/showthread.php?p=332682#post332682

use clockspeeds notes and a tester. If you test it pin to pin I bet you will find all the same traces he mentions. From there its just a matter of deciding the best place to cut. If you look you will notice the board is double layered and sometimes traces go through the board. When I looked I found several easy cuts and a few I needed to look for.

[ilavu]

well, NM, Looks like I got one!

Let the 102 Glitching continue....
LETS TRY NEW DELAY
Glitch Delay = 0337
VCC = 0F

--+---+---+---+---+---+---+---+---+--
TX Data : A1
===========================================
Glitch Success!! A0FF-INTERCEPT IS ON
BootLoader 6F 00 RSP Received!!
VCC = 03 (~5.88235294117647E-02 vdc)
Glitch Delay = 0337
Glitch type 06
===========================================
Card dumped in n2e b7 ok
I'll continue to work and see if I can get something going

Ill post picts and info soon for the rest of you t5 users



Hey Nefarious,

Can you or someone please give me more info please on 6 switch mod? I follow your step by step and confirm it with pics too. I am using 25 ohms for 102 and only I get is ---------- no matter what setting is for pot and switch. Can you answer---

1. What is the switch setting?
2. What is the power supply spec?
3. What is the pot value and setting(ohms) to glitch?

Thanks.

[Nefarious]

did you read my write up?
http://www.dssftp.com/forum/showthread.php?p=332163#post332163

25 ohms pot aint gonna get it, I used 5k and found glitches about 1-2 k

9v power supply

script will autoglitch, the setting were right there in what you copied
Glitch Success!! A0FF-INTERCEPT IS ON
BootLoader 6F 00 RSP Received!!
VCC = 03 (~5.88235294117647E-02 vdc)
Glitch Delay = 0337
Glitch type 06

Seems to work best for me with pins 1 and 6 down. Insert your card before powering on the loader or it wont recognize the flash.