Dish 121 interrrupts signal x other birds...

[elrey]

Hi guys, Here is my question regarding dish 121, currently I have 3 dishes, 1 for bev, 1 for 110, and a 33" which I decided to set on dish 121. Everything was fine until I decided to add 121. it seems that whenever I connect 121 to any of the ports of the disecq switch this will mess up the signal or either bev or 110, to the point that I can not get the signal for either one. I don't know if the disecq is not working properly or is a setting problem, or I need I different switch. Need help please because everithing I tried does not seems to be working. Thank you.

[xwolfs7]

Hi guys, Here is my question regarding dish 121, currently I have 3 dishes, 1 for bev, 1 for 110, and a 33" which I decided to set on dish 121. Everything was fine until I decided to add 121. it seems that whenever I connect 121 to any of the ports of the disecq switch this will mess up the signal or either bev or 110, to the point that I can not get the signal for either one. I don't know if the disecq is not working properly or is a setting problem, or I need I different switch. Need help please because everithing I tried does not seems to be working. Thank you.

Hi! Try putting 121 22khz to "ON" and your others 22khz to "OFF" see if that works,good luck..

[dayshaun]

Hallo. i hve a atmega128 16ac 0222
i programe the atmege with a file name FN Atmega Duel Provider
The x channel are blank no message: to view this channel a new card must installed.
the channel 265 and 884 and the stars channel no message: to continue view this chanel
what can you telme about this thanks for help.

[calin]

You are posting in the wrong forum!!!!

[elrey]

Hi! Try putting 121 22khz to "ON" and your others 22khz to "OFF" see if that works,good luck..


Thank you for your advise, but I tried that too and it didn't work, I have tried many things but with no luck. I even tried setting up the 121 on the second lnb (dish setup) and the others on 1st lnb. well I will continue trying too see what I can fine, any more suggestions will be very appreciated. Thnak you.

[xwolfs7]

Thank you for your advise, but I tried that too and it didn't work, I have tried many things but with no luck. I even tried setting up the 121 on the second lnb (dish setup) and the others on 1st lnb. well I will continue trying too see what I can fine, any more suggestions will be very appreciated. Thnak you.

Hi! What kind of LNB you using for 121,you should be able to get them all at once,I am on 12 birds on one 4x1 disqc switch myself.

If your using KU LNB set the frequency to 10600 and have 22khz set to "ON"
I`m using a universal fortec star ku LNB myself but have used a standard KU LNB as well and both worked.

What kind of disqc switch you using I have pansat disqc switch but used a microyal as well,could be your switch .

I`ll try and look around see if I can find siomilar problem and how to resolve it,good luck..

[elrey]

Thank you for your reply, right now I am using a blackbird st2000 a ku lnb set at 10750 for 121 and 18' for bev and 110 and a 1.2 diseqc swith, it works well if I disconect 110. Originally I had bev and port a, and 110 on port b. they both work well, then when I connected 121, 110 started interfiering with bev, a very strange situation in where port a for bev will pick up 110 signal or viceversa, then I move them all around and bev is ok but 121 interfiers with 110, the same symptom as with bev and 110. and I also tried other settings for 22mhz etc but nothing seems to be correcting the problem. I don't know if it is the switch that has gone bad. Anyway thank you for your reply, and keep me posted if you find something else. Thanks.

[elrey]

Thank you for your advise, it works at 10600 with 22khz off, but I'm still missing a couple of channels, but I think the problem is on the aiming of the dish, I might just need to tilt the the dish a few centemiters or so to see if I get all the channels on that particular tp. Thanks again for your help.