no signal on mytheatre

[liftedz71]

I have a twinhan vp-1020a that is hooked up to 119 directly. When I scan 119 it says that there is no signal on all transponders. If I connect the cable to my receiver I show that there is a signal. The lnb is a dave lnb. I know it is fine because I am using it with youvs with no problems. I tried setting lof1 and lof2 to 11250000 and sw to 0 and it did not work. I also have a diseqc 4x1 switch that I tried and it also did not work. I imported a 119ini and that also did not work. If anyone has a suggestion I would greatly appreciate it.

[JackGoff]

mine is doing the same thing and it was working last night... does something need updated?

[buzzharley]

Did your 1020a come with 1 or 2 installation cds?

[liftedz71]

it came with one installation cd. it has visiondtv software and drivers on it.

[puzzlepad]

I have a twinhan vp-1020a that is hooked up to 119 directly. When I scan 119 it says that there is no signal on all transponders. If I connect the cable to my receiver I show that there is a signal. The lnb is a dave lnb. I know it is fine because I am using it with youvs with no problems. I tried setting lof1 and lof2 to 11250000 and sw to 0 and it did not work. I also have a diseqc 4x1 switch that I tried and it also did not work. I imported a 119ini and that also did not work. If anyone has a suggestion I would greatly appreciate it.

First, what software are you using? There are different procedures for different software. Download the lastest Progfvb; it is the easiest to setup. Replace the old plugins folder new update plugins folder on this latest s2emu.dll, all the seca files, latest capi patch, and the latest softcam file with the new DN keys. Click on DISECQ, look for Echo9, then click on circular lnb, input LOF setting 1125O, final scan Echo9. That's all.

[liftedz71]

I am trying to use mytheatre. I will try progdvb. where can i find the seca files at. and i also notice that echo9 is not listed in the program.

[desrever]

I am trying to use mytheatre. I will try progdvb. where can i find the seca files at. and i also notice that echo9 is not listed in the program.

These are my setting and work great

For MyTheater

First pick Correct Sat

Deseqc Nothing checked

LOF1 11250000 Change then click apply
SW 12700000 Change then click apply
LOF2 0 Change then click apply

Close Program then reload

Go back to sat make sure all settings are the same as above

Sel All

Now Scan

Enjoy

[sukh77]

You don't need to install the program that comes on the cd. Its worthless.
You only need to make sure windows can see the card and install the drivers from that cd that's all. then set up Mytheatre.

LOF1 = 11250000
SW = 0
LOF2 = 11250000

Are u using any switches? Did the card come with a switch?

[slikk76]

echostar7= 119
echostar6,8= 110

[liftedz71]

I figured it out and now receive the channels on 119. I do have a question about mytheatre. How do you get to view in full screen so that the only thing on the screen is the channel? When I select full screen it still shows part of the software on the screen.

[BigSwifty]

Are you refering to the list on right pane? If so press L to toggle list on/off.

[liftedz71]

What about the list that is at the bottom of the screen. Is there a way to remove that from the screen.

[BigSwifty]

Settings (Ctrl+Alt+S) Display tab ... Status Line

[sukh77]

I just double click on the video and it expands just the video takes out the channel list and the stuff on bottom. Try going to different graphs and select a similar one or try all till it works the way I described.

[liftedz71]

Thanks for the help. I was able to get the video only on the full screen. Now hopefully we can figure out this damn crack. The 3.27 and 3.26 cracks did not work for me.

[neofrost]

I figured it out and now receive the channels on 119. I do have a question about mytheatre. How do you get to view in full screen so that the only thing on the screen is the channel? When I select full screen it still shows part of the software on the screen.


How did you figure it out? I have the same setup. I have tried MT,ProgDVB,ProgFinder and I still cannot get a signal. I get a full signal on my DN receiver.

Tried LOF1/SW/LOF2 at 11250/12700/0 and 11250/0/11250 (Mhz) No luck

I have a LNB from Dave point at 119- no switches- Twinhan102G card.

[#40Fan]

Try LOF1 and SW 0 and LOF2 11250.

Also, the 3.26 crack is working fine. Just need to read the nfo file.