Error:There is no audio track!

[joeman283]

Why when I click on the travel channel and it comes up with
Error:There is no audio track! what is wrong with it ?and what file do I need to open up that channel? most of the channels are working fine...Question #2 I don,t get ESPN but, I see ESPND and ESPNJ
Thank you in advance for your help

MT Ver3.31
VisionPlus TwinHan
P4: 2.8 Ghz
Ram: 512 mb
Video card: GeForce MX 4000 128Mb DDR
DishPro LNB with no Diseqc switch

[tigert422]

Why when I click on the travel channel and it comes up with
Error:There is no audio track! what is wrong with it ?and what file do I need to open up that channel? most of the channels are working fine...Question #2 I don,t get ESPN but, I see ESPND and ESPNJ
Thank you in advance for your help

MT Ver3.31
VisionPlus TwinHan
P4: 2.8 Ghz
Ram: 512 mb
Video card: GeForce MX 4000 128Mb DDR
DishPro LNB with no Diseqc switch Try doing a single rescan on this transpondent

12297 for travel channel and ESPN Classic USA

12326 for ESPN

Just rescan these two and see what you come up with . As far as your computer spec are concern they are more than enough. I have just checked both channel and am getting them without any problems. If you need more help just ask!! Have a Great Day!!

[joeman283]

tigert422,

when you said, doing a single rescan on this transpondent
can you please tell me how to do step by step and details please
I am a rookie and need more help then most people
thank you in advance.

[tigert422]

tigert422,

when you said, doing a single rescan on this transpondent
can you please tell me how to do step by step and details please
I am a rookie and need more help then most people
thank you in advance. Ok JoeMan go to this link
http://www.dssftp.com/forum/t48742-new-my-theater-set-up-instructions-and-programs.html

and you will find this statement:
Quote:
In same screen, right hand side, is a box with the transponder frequencies. Click on the first one to highlight it and then click on "Scan" (bottom right corner). If everything is setup properly, it should find channels. Do the same with each one of the transponders. Not all of them have channels though. You can "Sel. All" and then "Scan" but for some reason, it skips some channels. So, it is better to them "one at a time".
UnQuotr:
Right where it is telling you to scan all of your transpondents well just highlight just the one that I listed for you and scan just that one. After that scan is done then highlight the next transpondent that I gave you and scan it as well. After the scan is done exit out and see if you now have picture and sound again. Let us know how you made out!! Have a Great Evening!!

[joeman283]

tigert422,

I followed step by step in your sugestion, scan each transponder manually and I have about over 681 channels most of channels working fine, there is no
ESPN, ESPN2, Travel channel, TNT, USA and I don't need all of those channels I just need to get ESPN--->sports and Travel channel mainly because of world Poker tour on every wednesdays, I import 119 sat the one that comes with MT, maybe I am using DishPro LNB may need special channel list or any other advise from the expert on DVB-s out there, I am using VisionPlus TwinHan and Hauppauge Nexus on 3 diff computers same results.
I am running out of ideas...please help.
Thank you in advance for your kindness and your time for helping me.
have a good day :-).

MT Ver3.31
VisionPlus TwinHan
P4: 2.8 Ghz
Ram: 512 mb
Video card: GeForce MX 4000 128Mb DDR
DishPro LNB with no Diseqc switch

[#40Fan]

Try Lof 1 and SW at 0, and Lof 2 at 1125 for both sats.

Committed LNB1 for 119 and LNB2 for 110.

You do need to be using the DishPro.ini files that can be found in the download section.

[joeman283]

#40Fan,


Where do I put DishPro.ini files in? plugin folder or in MT folder?
I am a rookie needs a lot of help.
and I will try your sugestion and will update the results later.
Thanks again

[#40Fan]

You need to download them, the go into the Settings, LNB/Diseqc settings. Then click on the import button, bottom middle.

First import the Echo 7.ini. Then hit the Diseqc button. Change to Committed 1 and check the box next to it. Hit Do Now, the OK. Then change the lof 1 and sw to 0 and then lof 2 to 1125. Make sure you hit apply now.

Now, import the Echo 6/8.ini. Do the same as above, but use committed lnb2.

After you are done, select one of the above sats and scan all of the transponders by hitting the Sel All button, and then Scan.

[joeman283]

I want to Thank you #40Fan and tigert422 for taking their time helping me out
I have ESPN, ESPN2, Travel channel, TNT, USA now, this website has a lot of smart people and thanks again.