Can Anyone Confirm Atmega is working or not?

[500 MG]

I just wondering Atmega is working

[spanky]

this is the AVR-X forum not atmega
and any confirms will be for dealer done which people say are working

[freecharlie]

Actually, I don't think there is a forum for the atmega, so for those interested in alternatives to AVR-X or in doing a cost comparison, this forum would apply, indirectly anyways...

Now watch the guillotines fall!
FC

[500 MG]

Atmega freeware will be out soon.

Thanks TenBlade

[Morpheux]

This is the atmega forum, for some reason no longer shows in the forum menu.
http://www.dssftp.com/forum/f7-dish-and-bev-avr---atmega-questions.html

[Dish it.]

Atmeag's and the old plastice is up and hauling ass.

[Groomer]

Where is the best place to find info on Atmegas running N2?

[peter123]

just read on ... rom10x dot com that as early as tommorrow we may see something for the atmega cards.

whoooooooooooooooo:)

[Nakedmadman]

Atmega is working!!!!
rom10x dot com (http://www.rom10x.com)

[Morpheux]

They apparently are...gotta try that as soon as i get home

[rambo41]

Up and running wide open on a 3100 ird as of last nite....... :)

[bacontits]

running on 2800 after about 5 minutes of work

[MarvinGardens]

With a simple IRD flash and Atmega flash, mine has been running wide open on a 301.010 for the past two days.

[rocketman]

hell i am newbie took me about two hours been up since last night thanks to all that helped...........

[tv2004]

Working beautiful but I'm having trouble with my 2700 CAPD, after flash, it doesn't show any signal. Any hint ?

[Nakedmadman]

I have a 301.010 and it's been up and running for almost 2 days now........all channels wide open!
Is there any reason why this is under the "Bogus and utter bullshit Nagra 2 hacks" when it has been confirmed working!

[playme1979]

the peeps here are very far behind lol

[niceman99]

working here on 2700, 301-10 and 301-13 ...the 13 took many attempts but got it working..

[Glock]

just got my 3900 today, took awhile to sift through on the instructions and reflashes but I just got it up. be nice to have the forum open again

[Glock]

Can anyone tell me how to edit the time zone. I did a flash with jeepers so it did not give me any options.

[stevemac800]

yes atmega working 100 % and rom 10 working 100%

[pimpin]

K... working on getting this up and running. Reflashed a 2700 BEV reciever to dish but having problems changing the building Config on the Eeprom. What Hex editor is everybody using to get this running?

[sukh77]

What Timezone is it using right now.

[madmadmad]

where can one find instructions for setting up an amega 128 on a 4900

[smilingjack]

general dish and bev

[Glock]

IT ON EAST NOW i NEED CENTRAL. I bet if I knew the code to change in the eeprom i could use hex editor to change that code. Anyone have it?

To answer a queston above. I google hex workshop www.download.com/Hex-Workshop/3000-2352_4-10264932.html

[sukh77]

Then its either EC or F0(zero). Find text EC or F0 then replace with what you need.

[livnitup731]

All crystals are working. Read rom10x to see how. If you are getting error 19, redo the card a couple times.

[ussatravel]

Can anyone tell me how to edit the time zone. I did a flash with jeepers so it did not give me any options.
Down load this program and see if it is not what your need.

[ussatravel]

Can anyone tell me how to edit the time zone. I did a flash with jeepers so it did not give me any options.
download the attached file and see if it is wha you heed.

[sahko]

Does the N2 Atmega fix (Flash+EEPROM) also work for BEV?

[smilingjack]

They are working on converting the dish hack to bev.
It should work, DVB is up on BEV and FTA is working on it too
Keep an eye on the ATMega thread