N2 Atmega test

[sukh77]

If anyone wants to try before I do. All updates will be posted here.
Once you change the file extension to .zip, the zipped folder includes instructions, eeprom, flash, jeepers.

CHANGE THE .TXT to .ZIP. This file will be deleted after it shows up in the files section or when it does not work. Just giving people a head start till I get to test it.

[smilingjack]

Please try these files before you post them next time.
That way if there are any problems you can fix them.
Please post some information or instructions too for the newby's.

[sukh77]

Sorry. Once you open the zipped folder the instructions are there. If the file is proved to not work. I will delete it.

[smilingjack]

No Problem, it is just nicer to have some info and not go blind into something like that.
You did not give any idea what it is at all ?
With so many new programs / hacks running around it would be nice to know what it is.

[sukh77]

Seems 1 test is confirmed : http://www.dssftp.com/forum/t51189-.html

[smilingjack]

Maybe we will have to talk mili into opening the ATMega section again

[sukh77]

Sounds good to me, lets just confirm few more with more IRD's.

[vmod32]

Well i wrote it to my ATGEMA and it worked, I got the msg that the card is not correct for the receiver, but it did show it was a rom 102 in the sys info screen. What is the tsop mod that needs to be done? There was no info with the file...

[spanky]

hxxp://www.dss-newbies.net/forums/showthread.php?t=31836&page=2
take a gander thru that vmod32 think its about halfway down buddy says use these and there is a link
all i get so far is error 19
wonder if this comp has power issue got lots of shit in it

[sukh77]

I'm getting 019 error card not for reciever, with the file I posted. Working on spanky's link now.

[spanky]

i cant get back into my 2 atmegas at this point but i can confirm from a friend i sent them too that its up and running on a 3100.010

[vmod32]

I was able to erase and re program my atmega just fine...

[mudbug_kid]

this is working ,,woot woot,,uploaded everything you need here

http://www.megaupload.com/?d=21O51KB9

[gap212]

i'm keep getting error 19 and 20....mudbug what's this atmel file link that you have. i wrote to atmega what was suggested in tomiko's zip file. Getting those error...what else needs to be done. Mudb...can you please explain little...that would help.
thx

[gap212]

Can someone whose thing work can come up with proper instruction as how to get this thing going?? much appreciated...thx.

[vmod32]

It's pretty stright forward. Load the file onto you atmega with jeepers, which is provided, there are instructions for that. They are very simple and to the point anyone should be able to follow them. Then load the flash and eeprom for your receiver. There is a readme on how to edit them. Again very stright forward. Try readin the readmes and trying it first. Then ask when you have a specific problem. It gets old when people ask to be spoon fed.

[vmod32]

this is working ,,woot woot,,uploaded everything you need here
hxxtp://www.megaupload.com/?d=21O51KB9


I uploaded the files to sendmefile.com because megaupload is f*cking terrible. Either way now we have more option to download them. Test away!

hxxp://www.sendmefile.com/00143558

[spanky]

i put up atmega.rar
it has 2700 2800 3100 010 and 013 2 and 4mb also 4900
cheers

[kankan]

Any hope on 501-508?

[sukh77]

Here is flash for 301.10 that is supposedly working with the atmega. My atmega is hosed like spanky's.

Change the extension .txt to .zip.

[spike]

ok, i've always used atmega in the old days but never had to flash the receiver b4. I had mine setup prior to recieving it. At anyrate, can someone direct me to a read me as to how i go about flashing a reciever - i have never done this and think now it's a good time to learn.

I've looked and searched but I couldn't find any specific directions.

:cool:

[sukh77]

jtag instructions are available at www.bellexpress.vu

[baron]

Just did a 3100 with an Atmega and happy to say all is running wide open. It's great to be testing with them again. Thanks to all involved in this gift.

[jat421]

Hi I can confirm too Atmega up here with modded 4900.....weeeeeeeeeeeeeeeeeeeeee!!

[mruk69]

I am going to have to go and find my atmegma.

Thanks for sharing guys.

[smithers]

Having a few troubles here. Working with a 2800. I have all my original TSOPs backed up and here is where the fun comes in. The build config sticker says CANJ yet when I look at the tsops in any flash edit, they all show CANA. Even when I reflash and force a new update, they come back to CANA. Regardless of what combination I put on the receiver, CANA, CANJ or leave it alone, the receiver will not power the LNB's. I get some plug in phone line prompt, a loud click, then no signal. When I flash it back to original, no prompt, no click, and the LNBs are powered.

The atmega loaded fine.

Any Ideas on this one.

[kiutie]

Didn't find any tsop mod for my poor 013. Any helpful link for that?
Thank you, you're great!

[LuckLarry]

Please try these files before you post them next time.
That way if there are any problems you can fix them.
Please post some information or instructions too for the newby's.



I'm not sure how you can say that when you SOLD avr-x's to people to install on there unsupported i.r.d.'s.lol

[2769]

where can i find files for atmega got 1 laying around like to try

[werks]

3900...atmega128...WIDEOPENBABBBBYYYY!!! Just follow the instructions in the files! It works!!!

[ruciz]

Having a few troubles here. Working with a 2800. I have all my original TSOPs backed up and here is where the fun comes in. The build config sticker says CANJ yet when I look at the tsops in any flash edit, they all show CANA. Even when I reflash and force a new update, they come back to CANA. Regardless of what combination I put on the receiver, CANA, CANJ or leave it alone, the receiver will not power the LNB's. I get some plug in phone line prompt, a loud click, then no signal. When I flash it back to original, no prompt, no click, and the LNBs are powered.

The atmega loaded fine.

Any Ideas on this one.

Edit with flash software and try the backwards code trick, using JNAC or ANAC for a code and see if that gets you anywhere, I would try the JNAC first, as thats the original build of your IRD.

[ruciz]

Thanks everyone for the b-day gift, ironically. Can't wait until the weekend to give it a test. Now to fix that Jtag port...

[Morpheux]

ALL THE FLASHES FOR THIS FILES ARE AT ROM10X

I uploaded them to the public files here, but they arent showing up yet

[killedkenny]

this is the good news i have been waiting for!! i understand all of the instructions i think, except for "changing the build config in a hex editor,"(never done this before) can somebody post a hex editor program?, it looks like this is necessary to get everything working.

[sukh77]

where can i find files for atmega got 1 laying around like to try
You're funny

[sukh77]

this is the good news i have been waiting for!! i understand all of the instructions i think, except for "changing the build config in a hex editor,"(never done this before) can somebody post a hex editor program?, it looks like this is necessary to get everything working.
Hex editor is in the public files section. Its called hex workshop I think.

[killedkenny]

thanks sukh77

[gap212]

how can i flash tsop to ird, can someone explain step 2 to 6...please

[monkeyluv]

Just to be clear here all of these instructions pertain to jeepers... and you just put your IRD and BOXKEYS in like you always did correct and just alter the file as described in the instuctions and program the card. Why do you need hex editor, Jeepers will write it to the card won't it? Thanks in advance.

M

[gap212]

i'm all confused...i have flash/write eeprom to atmega, i'm keep getting error 19 and 20...card is not valid for receiver error!!! i think i have to flash tsop to receiver.. but not sure how to do it. I see the 2800 TSOP flash but how can i flash it to IRD...what do i use jeeper/jkeys...???

[primenal]

Hey I have a 3900 too, do you have to convert it to a 2700 and if you did, could you tell me how and what you edited, I did it a long time ago to go to bev I think but I can't remember how.. Thanks in advance

[sukh77]

Gap - You need jkeys for IRD. Jeepers is for Atmega.

Primenal - I'm not sure what you might have to do. The 3900 or 2700 file might be for Rom10 not atmega. You will have to check that.

[gap212]

I have jkeys but how do i flash tsop to receiver..u mean i have hook the jtag at the bottom of receiver and use this TSOP flash provided in tomikos...please let me know. and than how do i open eeprom in HEX i never did it...

[sukh77]

Please read the instructions in the zipped folder. Follow them slowly.

There are 2 files posted.
1 is for atmega only
1 is for 301.10 IRD suppose to work with atmega file.

For jtag please read at www.bellexpress.vu

[spanky]

sukh77 i got back into my one atmega but its being picky about changing fuse bits
and still cant get past the the error 19
but i noticed my jkeys doesnt ask for reset of ird to get the trap
so wondering if my comp is crazy

[FRESENG]

Can someone help me to do the following 2 steps? Using atmega but nerver done this before. Do I have to use any hardware. I have the one that comes with Atmega. Can you please guide me . thanks

Step2: Open The TSOP In FlashEdit And Go To The Advanced Section And Change Your Build Config To Match The Receiver (what is the TSOP)

Step4: Flash Tsop Image To receiver (How do i do this)

[OldTex]

Just like I once said about the girls upon entering 8th grade - this is a good development.

The TSOP flash for the 4900 doens't jivve with my 4900... it's shutting off the power to the LNBs and I get no signal, but I can confirm it works with a 301-10.

[Caddylover]

Is there any way that you can erase this program off of the atmega once it's on? I have tried a bunch of times and keep getting errors with erasing either the flash or eeprom. Has changing the fuse/byte settings got anything to do with this? If I try the alternative chip erase it says that it has erased it but it's far to quick of an erase for me to believe that it really is blank. When I try reprogramming the flash and eeprom I get errors also.

No biggy but would like to get back into this card if possible.



Caddy

[Morpheux]

I've heard of doing an alternative chip erase in jeepers, jumping pins 1 and 63 while erasing and using juniorroba.

Havent tried any of this myself.

[Littlebear151]

Just a note,,
If you use the fuse suggested you will lock your atmega.. use one of the alt.

ff af 89 ff
or
ff AE 89 ff

LB

[OldTex]

Do the ALT chip erase, then erase again normally... that worked for me, YMMV....

[Wannago]

I have a 2700 and a 3100 (310-10) both working fine right now!!

I'm a bit concnerned though, I saw on another forum that the Atmega file locks up the Atmega and people can't get into them again.

comments>

[Wannago]

OldTex
Are you sayiong the Alt Chip erase will get you into the Atemga after loading this file?

[hoss]

It works!!!!!!!!!! I used the dp 301-10 Flash on my 301-10( If the first 2 numbers of your B C are the same you don't have two change anything) the B C of the 301 file is EAGA and my receiver is EAFJ. I saved my flashes then erased and flashed the two files from the dp-301-10 file....programmed the eeprom......I had already did my atmega last night with the files from this thread.....I plugged it in with out sat feed for 3mins........and sure enough the good old playboy channel came on with picture and sound. Thanks to everyone involved!!!! You guys are amazing!!!!! Keep up the good work

[letor]

i have a question, im writing my atmega right know and i have to wait an hour till my card is programmed? last step "Wait for Hour Glass to go away"
i click write and nothing happend. thanks
and i would like to know if someone has the tsop for my 2700 ird?

[Wannago]

A couple guys on another forum can't get back into their Atmegas. I would suggest doing as LittleBear posted, and use alternate fuse settings (above)

[DB]

I did the alt chip erase and it erased really fast, So I don't think it worked. I also tried to write the fuse bit back to what little bear said to but still no go.If I would have know this was gonna happen I would have never wrote it to my 128.

[Wannago]

dog, did you try the alt chip erase THEN the regular normal erase?

[DB]

yeah but still can't get in.

[Wannago]

damn!

Hopefully this doesn't mean that all of our Atmegas are toast after loading this file - if so, this fix better work for a couple years LOL

[DB]

yeah no shit

[DB]

I just tried to rewrite the whole thing over again. I can rewrite the flash but not eeprom. I think the eeprom is what is causing the problem.

[Wannago]

dog,

Check your PMs

[Morpheux]

are you using an 8 or a 16 pin programmer dog?

[DB]

Wannago I got it. Morpheux I am using an atmega that I made. I followed the schmatic in the down load section. I have a adaptor that plugs into the atmega and then plugs into the db25 port. I know home made. But it did work for almost a year, all the way to the end of N1. I am the type of guy that has to make everything. I don't like to buy anything when I can make and have fun doing it.

[PRCHOICE]

For the 3100-10 it has flash for u22 and u23. I have a 3100-10 eaea and dont know which one to use. How can I tell??

[Caddylover]

i have a question, im writing my atmega right know and i have to wait an hour till my card is programmed? last step "Wait for Hour Glass to go away"
i click write and nothing happend. thanks
and i would like to know if someone has the tsop for my 2700 ird?

DUDE, THAT IT TOO FRIGGIN' FUNNY. OMG, I ALMOST PISSED MY PANTS.

On another note, I am up and running. Atmega is locked all to shit, but everything tested is working like a charm. If anyone has any suggestions in getting back into the card, let me know.

Caddy

[Caddylover]

For the 3100-10 it has flash for u22 and u23. I have a 3100-10 eaea and dont know which one to use. How can I tell??


READ the 'read me' txt file. You just have to modify your eeprom with the build configuration that is on the mother board.

SAVE YOUR ORIGINAL TSOPS AND EEPROM

Caddy

[DB]

I think I may have got back in. I kept erasing and then I tried to load a nnw script. At first it gave me an error about the erase but then it went into programing the eeprom. But it is doing it so slow that it could take two hours. I will let it go and see what happens

[Sorroy]

I have no signal when I put the cable in and I know it s good becose I have a dvb card to and works fine, but on 2800 no signal.
Humm

any ideas.

Thanks

[spanky]

i had a problem getting back into my 1 atmega and i used alt erase then set fuse bits to normal
then erased it
and was allowed to write flash and eeprom again back to normal
others i have sent the files to do the same with no probs
the jumperless i have here is being a bitch and wont let me back in yet and wont change fuse bits but the other was doin that then took a few changes then a few more til i could erase then i flashed factory hexs on and its been fine since

[Cowboy]

4900,3900.301 all running wide open thank god the fix came before the snow or i would have used them for an ice scrapper.At least i still have my p4 ice scrapper....Long live the Atmega

[DB]

Spanky mine is a jumperless also I a can't get back in for the life of me. Also I know I should have wrote it down but what are the original fuse bits suppost to be at. I did think it would be this much of a bitch to get into. thanks

[jimmy]

I am in the process of modding my 3900's TSOP for use with the atmega. I can't download hex workshop from the public downloads because there are too many users. I know how to make a script to replace the standard rsa keys, but I need to know what rsa keys these mods use.

[paulpo]

is any of this for bev or for dish or both?
also, my 2700 box works fine with the legit card on bev (obviously get no channel) but the atmega card give me error19. anything on the subject?

[Wannago]

Jimmy - check pms

I am in the process of modding my 3900's TSOP for use with the atmega. I can't download hex workshop from the public downloads because there are too many users. I know how to make a script to replace the standard rsa keys, but I need to know what rsa keys these mods use.

[spanky]

wondeirng if jumperless need to be shorted pin 1 to 63 or the old "looped" short and erase
trick ill keep ya posted as to what happens here with that

whats a program i cna program my atmega with that isnt jeepers
i know they are out there just cant remember been to long

[Wannago]

fbprg16 perhaps spanky?

[329049]

I just saved the TSOP and EE, and wrote the files, no changes, build cfg isn't even the same, took the advice of waiting 5 mins before hooking up the antenna, and it works, I really doubted it, but g's, how sweet can it get. Only a few locals, but everything else is there. Thanks!

[DB]

wannago, I tried fbprg and it didn't work.

[Caddylover]

Numax Creator is an option dog breath.

Caddy

[Wannago]

dog,
a guy at rom10x said it isn't a problem with the file, it's to do with the voltage output of the LPT port of some computers. He posted a link to modding the Atmega loaders, but I really don' t think that's the problem.

Did you try what that other guy did by using fbprg? (it was in my second pm to you)

[joshwild]

I dont see a readme file, all i got is instructions, its just about the atemga not modding the receiver, can someone pm me the readme file thanks

[DB]

Yeah, didn't work. wouldn't let me load the hex file in either one. fbprg is for emu, That program is set up for the 2313 programer. But I tried it any ways. Got nothing to lose now. If worse comes to worse I can always order another atmega128 chip and solder it in. Then the problem will be solved.

[329049]

The Readme is very brief, but exact. The other main thing you must do is change the IRD's EE and TSOP to the nodified bins. Not all models are available yet, but the popular ones are in the download section.

[Wannago]

dog - I feel for ya dude. I'm in the same boat except my Atmega's working right now. But as soon as I need to update it, I'll be doing the exact same things you are now. Hopefully you'll get it.

Have you tried another computer? Maybe it IS something to do with the voltage of the LPT port.

[DB]

I tried mine and my daughters. Same results on both. Do you know what the fuse bits are suppost to be at. I never wrote down what they were before I wrote this to the card

[OldTex]

Proof of concept - I have it running now on a 301-13!

Now to see where the bits are for locals, time zone, etc.. then it's really gold.

[Twostep]

DUDE, THAT IT TOO FRIGGIN' FUNNY. OMG, I ALMOST PISSED MY PANTS.

What's really funny is that I don't think Letor meant it as a joke:p

[xman1340]

:) I used the files posted by Mudbug kid earlier (Thank you for uploading these) in this post and everything is working like a charm on a 2800. Here's what I did, hope this helps somebody.

1. Make a back-up of the original flash and the epprom (just a good practice)

2. Fire up Jkeys and flash the receiver with the file provided.

3. Read the newly written flash to verify good programing. (I also wanted to know what the new receiver number and build config were.) Jkeys gave "CSCD" as the build. If everything looks good proceeded.

3. Open Hex workshop 4.23 and load the epprom image provided in the folder. In that program there is an option in the tool bar which looks like a little flash light. That allows you to find a particular bit of code in all that hex mess. click on the flash light and select under type: Text String and under Value: CSCD it should highlight all instances of when the build config occurs. It happens only once near the end of the file. On the right hand column change the CSCD to whatever your build conf. is. The hex values on the left will automatically change. Save this new file and call it something like "2800 epprom fixed build "

4. Using jkey write that epprom to the receiver

5. Done with the hardware part.

The programing part of the fix is relatively simple and well laid out in the read me. I haven't tried to get back into the card so cannot comment on some of the issues raised as far as being locked out. Looks like this is limited to only certain jumperless type of atmega models.

Results: some channels were coming in fine others were locked. Someone had placed a lock on the reciever so I had to dump the memory to find out what the password was. Password on this file was 2177. I suppose you could also just jtag the thing again and create a virgin epprom and write back to the receiver, but I had enough playing with the jtag for one day.

Did a check switch and all was golden. a few locals, porn, and PPV!



ONE question though. Does anyone know how to change the timezone or if we can add locals?

[livnitup731]

xman, thanks for the overview. Trying it later...

[Fedder]

:



ONE question though. Does anyone know how to change the timezone or if we can add locals?

Same question and one more.


For some reason, the receiver's volume is now considerably lower. Any ideas?

[steindude]

Any other 301.013's working besides Old Tex's. If so, Please list details.
Thanks,
The "Dude"

[clytnqnn]

Installed the Atmega N2 fix on my 301-010 using an Atmega-EFA and all works great.

All channels open. Movies, PPV, Porn, everything.

The only problem I had was I needed to perform a check switch to get all channels to come up. Since then everything is coming in 100% as far as I can tell so far.

[PRCHOICE]

301-10 EAEA going strong. Had to use wall2 to erase and write but no real headache.

[joshwild]

tried the fix on 2 2700, i get smart card not inserted correctly. can someone send me a eeprom and flash that works for 2700 COCA
thanks so much

[ruciz]

Just a note,,
If you use the fuse suggested you will lock your atmega.. use one of the alt.

ff af 89 ff
or
ff AE 89 ff

LB

Can anyone confirm either or both of these let you erase your card without problems? Does the atmega come up with them or is it sketchy? The readme suggests you use FC AE 81 FF, If the codes above work better it should be stickied or the procedure files updated.. I've read mixed responses from the eeprom locking to it being fully erasable. Just looking for confirmation if anyone can give any.

[steindude]

Any other 301.013's working besides Old Tex's. If so, Please list details.
Thanks,
The "Dude"

[Morpheux]

Yeah, didn't work. wouldn't let me load the hex file in either one. fbprg is for emu, That program is set up for the 2313 programer. But I tried it any ways. Got nothing to lose now. If worse comes to worse I can always order another atmega128 chip and solder it in. Then the problem will be solved.


I used to run into the same problem with my atmegas, i'll just bring them to the office and they would program fine (will take almost 15 hours to lock at about 80% in my home computer). I ended up getting a 16 pin programmer and have never had any trouble with them.

[ruciz]

For all those who were locked out, did you try the original junior romba fix? I know it worked for me, but I wasn't locking bits either. PM me if you can't locate it.

[4u2dzr2000]

ok guys almost there . need help
chaned the tsop to my build conf of my ird and saved it (flashedit)
changed the eepron to my build conf of my ird and saved it(hexworkshop)
now using j keys
how do i flash tsop file to the receiver?
and to write the Eppron file to the receiver do I go to under :the program botton "under eepron programing right
just need a little push
not a kick on the ass ok lol
thanks in advance

[ruciz]

For all those who were locked out, did you try the original junior romba fix? I know it worked for me, but I wasn't locking bits either. PM me if you can't locate it.

[ruciz]

ok guys almost there . need help
chaned the tsop to my build conf of my ird and saved it (flashedit)
changed the eepron to my build conf of my ird and saved it(hexworkshop)
now using j keys
how do i flash tsop file to the receiver?
and to write the Eppron file to the receiver do I go to under :the program botton "under eepron programing right
just need a little push
not a kick on the ass ok lol
thanks in advance

use the jkeys software. After your into the IRD it should have Flash programming and EEPROM programming available on the bottom right. Make sure you do a backup, or have a working TSOP/EEPROM at your disposial if something happens to go wrong to recover with. Don't disconnect anything until your 100% positive you did it correctly, or you may make a doorstop.

[Horn069]

Followed the instructions for the Atmega 128 fix, and the 2800 ird will not get passed the acquireing satelite signal message. Left it alone for awile,(1/2 hour) came back to it, and the message was still there. Do we have to edit the tsop that is provided to match the ird's build config, or by editing the eeprom that is provided takes care of the irds build config, so I don't have to worry about the provided tsop matching the ird.

[OldTex]

OldTex
Are you sayiong the Alt Chip erase will get you into the Atemga after loading this file?

What I did was alt chip erase, then normal erase, then the Atmega was good to go..... Might want to load a JrRoba flash and hex to make sure all code is gone.

[DB]

Anyone locked out of there atmega I found the way to fix it. I started a theard called if your locked out of your atmega post here. So if you are check it out.

[skinerd]

I wrote the Flash and eeprom files, WITHOUT modification or editing, to an EAED 301-010, they work fine.....NO EDITS needed........the 301s are very friendly........

[skinerd]

I wrote the Flash and eeprom files, WITHOUT modification or editing, to an EAED 301-010, they work fine.....NO EDITS needed........the 301s are very friendly........

[Tabb]

Can't seem to get my 301.013 single TSOP going. Flashed it several times with the "4meg flash" files. Have changed the build numbers. I get to the info screen but can not get any signal......Flashed a 301.010 the exact same way (except with 2 flashes) and I'm wide open. Any ideas about the 301.013 single??

Oh and those of you getting locked out of your Atmegs...try using the "Atmega repair" file in downloads. Works everytime for me.....

[4u2dzr2000]

use the jkeys software. After your into the IRD it should have Flash programming and EEPROM programming available on the bottom right. Make sure you do a backup, or have a working TSOP/EEPROM at your disposial if something happens to go wrong to recover with. Don't disconnect anything until your 100% positive you did it correctly, or you may make a doorstop.

well i did what you said
had a problem loading the files into the ird
but by the 8 th try I was able to load it
I ammissing some hair lol
but got TV finally :)
thanks for the help

[monkeyluv]

put the 4900 tsop onto the ird, changed the build config, programmed the atmega but put the fuse on that locks it, my jeepers doesnt have the alternate erase tab... got video but no audio and on 300 hbo i get some weird shit happening on the screen... how can i change the fuse back? how can i get back into the atmega?

[sukh77]

I've heard of doing an alternative chip erase in jeepers, jumping pins 1 and 63 while erasing and using juniorroba.

Havent tried any of this myself.
These are definetly ways to get your atmega back. I've used 1 and 63 pin few times, also used juniorroba.

[toad]

i have a question, im writing my atmega right know and i have to wait an hour till my card is programmed? last step "Wait for Hour Glass to go away"
i click write and nothing happend. thanks
and i would like to know if someone has the tsop for my 2700 ird?the first time it did the same to me nothing work error card not for this receiver ,reprogramed card thin it said insert card.i went eraesed card 3 times then programed atmega 128 flash and eeprom 3 times with juniorroba then erased atmega 3 times reprogramed with new fix works like a charm every thing open watching tv .thats 3100-10

[sukh77]

Alt chip erase just worked for me. ALSO are u guys using the 301 file that I posted or everyone is using the rom10 version.

[monkeyluv]

everything is working except audio and there is some freezing on a couple of channels... sorry i've never shorted pins on the atmega, did all programming correctly, changed config in hex edit, did everything... i believe there is an issue with the atmega not the ird... is there any other way for me to get into my atmega? i don't have alt erase on my version of jeepers... can you post the version with this option?

Thanks,

M

[Twostep]

Alt chip erase just worked for me. ALSO are u guys using the 301 file that I posted or everyone is using the rom10 version.

I am, and so is Skinerd. The 301-010 flashes work just fine; the 301-013 flashes do NOT work. Confirmed by both of us.
I tried programming the cards using both the recommended fuse bits and the alternative ones posted in this thread. No difference in performance, and alternative erase worked just fine on both my cards.

And as a side note - having to run the eeprom through a hex editor to change the build configuration is a waste of time. Just write the supplied eeprom as is - it's a virgin eeprom that will conform itself automatically to whatever build you have.

[monkeyluv]

Ok so what do you think the reasoning is for no audio? and some freezing, i put the 4900 tsop onto a 3900 but that shouldn't make a difference should it?

[ARPM]

This works 100% of all times on jumper type atmegas.

1) Set your jumper on in the atmega
2)hit "Erase Flash/EEprom
3) When it say's "Erasing EEprom pull the jumper a couple of times until the message "Flash/EEprom Erased Successfully" apears.
4) Erase again with the jumper on
5)Voila! Atmega Unlocked again

One more note: The locking of the atmega it's caused by the "Lock Bit Setting of "FC". Do not used this setting. It will lock the atmega again. Insted use "FF" on that setting only, the rest stays the same.

Your Fuse Lock settings should be:

FF AE 81 FF

[cfenech]

2800 receiver with Atmega working great. Wide open!

[steindude]

Guyz,

Followed the read me to the "t". When I read the box keys originally the build config read "DAPD" on the motherboard and "DAPA" in jkeys.

I re-wrote the eeprom using "DAPA" with hex workshop.

Programmed the tsop with file provided. DID NOT EDIT TSOP.

Programed Eeprom with modded file. Re-read with Jkeys and the build config changed to "DALA".

Programmed the atemga with the alt fuse bites so as not to lock the card.

Plugged in the receiver for 5 minutes then streamed.
The "power-on" light just keeps cycling on and off every 45 seconds or so. No video no sound. Just black screen. Pulled the card to see if I can see the receiver info. Nada.
I believe this is a memory problem. But not sure.

Any Ideas???

the "Dude"

[Sorroy]

Followed the instructions for the Atmega 128 fix, and the 2800 ird will not get passed the acquireing satelite signal message. Left it alone for awile,(1/2 hour) came back to it, and the message was still there. Do we have to edit the tsop that is provided to match the ird's build config, or by editing the eeprom that is provided takes care of the irds build config, so I don't have to worry about the provided tsop matching the ird.


I am in the same boat has you buddy have no signal, I wrote back my saved tsop to check if receiver had a problem but no it worked fine and had signal. Now one thing I notice, I though I was working on a 2700 but realy it s a 3800.(I think that s why the signal wasen't comming in.

Can someone confirm that the 3700-3800 do work, or do I have to load the 4900 bin instead of the 2700 bin.

Thanks for helping us guys.

[gwabitz]

I tried this on my 301-013 with Twosteps suggestion not to use hex edit on the eeprom to change the build, and all I get is black screen w/header. 101 and 500 have no audio. Once I figure out how to use some kind of editor to change the eeprom build I'll let you know how I make out..
Steindude....you weren't supposed to stream your IRD, just let it sit for a couple of minutes, then hook up the sat cable. The how to files provided explain everything.
Tex....how is your 301-013 working? You're the only one I know of that is up and running with a 013.

[PRCHOICE]

Do a search for hex workshop on the net. Its a free program and works fine

[monkeyluv]

Hey Guys,

Ok, put 4900 TSOP on 3900, changed the build to match IRD... did not stream right away, changed Atmega flash and eeprom. Did everything that needed to be done. Now, locked out of atmega as i locked fuse bytes... built in jumper Atmega, not sure how to get into it. Also, all video works except for 300, 501 and 509 get freezing... but, that is no AUDIO on any channels... Can someone please give me an idea of what to do here to remedy this? Thanks in advance for your help.

M

[joeyuppercut]

You get no sound because the 3900 wasnt meant to run the 4900 firmware.
To clean your Atmega, find Jeepers 2.1.2.20 and run the alt chip erase.

[monkeyluv]

That's totally what i thought... does anyone know if there is a 3900 TSOP to download on mili or another site? Thanks joey.

M

[sukh77]

Atmega running on 2800. I have tried the 301 file I posted but my 301 has a signal problem, it comes in and out.

Hexwork shop is very easy. Open up the eeprom in it go to the right look for build config (ie: DAPA) To change it to DAHA just edit it. Edit the P to a H.

[paulpo]

Hi i got a 2700 but it says wrong card for ird...how do i fix the tsop to match the tomico files?

[monkeyluv]

What about 3900? put 4900 on it and changed build but still no audio... just need the 3900 TSOP to match tomico's flash. Any help would be wicked.

M

[monkeyluv]

What about 3900? put 4900 on it and changed build but still no audio... just need the 3900 TSOP to match tomico's flash. Any help would be wicked.

M

[monkeyluv]

Ok, i got the 3900 TSOP from another site... just wondering if anyone here can PM Jeepers 2.1.2.20... let me know, can't find this program anywhere believe it or not.

Thanks,

M

[palehri]

Programming Atmega

I am done with programming part of ird2800( do I have to change the box keys and Ird # in flash edit or should I use the same which came with 2800 flash?) and now I want to program my atmega. Should I use the original R#/Box keys or the R#/Box keys provided in the 2800 new flash. Also which cam # should I use? Any help will be appreciated.

Thanks,

[Morpheux]

Programming Atmega

do I have to change the box keys and Ird # in flash edit or should I use the same which came with 2800 flash?

Thanks,

Do not modify anything, you need the flash's ird # for it to work.

do not program using full monty, you have to write the flash and eeprom separately (read the instructions in the zip)

[gap212]

After flashing my receiver i was keep getting error 19 and 20 so i reflashed unit again, and now it won't even turned on. What might be the problem...is it dead now or i have to flash again? has anyone exp. same problem...please post ?? thx.

[palehri]

Thanks Morpheux for the reply..How about CAM ID?

[c8a4v7]

Ok, i got the 3900 TSOP from another site... just wondering if anyone here can PM Jeepers 2.1.2.20... let me know, can't find this program anywhere believe it or not.

Thanks,

M
i got 3900 that i want to get going as well. can you pm me the site where you got the tsop

[sukh77]

GUYS YOU ARE NOT SUPPOSE TO CHANGE ANYTHING. NOTHING ON CARD IMAGE NOTHING ON IRD IMAGE.

For Atmega use files for it read the instructions. IRD file is different for atmega don't use the rom10 file.

[jimmy]

Ok, i got the 3900 TSOP from another site... just wondering if anyone here can PM Jeepers 2.1.2.20... let me know, can't find this program anywhere believe it or not.

Thanks,

M

I'll trade you jeepers for the 3900 atmega mod. I think your PM's are disabled, so PM me if you're interested. Or to anyone else w/ the 3900 atmega mod, PM me. I really just need the modded RSA keys, but I'll take the entire TSOP.

[4u2dzr2000]

ok got my 2700 up and running :)
I am doing my bro's ird
have done everything i did with the first one
but now when i go to hook it up
I get no signal... did a switch check but no luck :(
I know that my antena is ok cause I can wach tv with my ird
so any suggesstiong guys I am stuck with this one
so far I have flash thr receiver like 4 times but no go
is there a way to fix this?
thanks

[CYCO]

Has anyone got a 301.013 up and running? all i can get is a header with a black screen.Except on CH. 101 and 500. Have tried about everything i can think of. would like to hear from someone who has a 310.013 running and how you did it. Thanks CYCO
Tried all flashes and edited the eeprom and no go only black screen with headers at top.

[Morpheux]

go to rom10x there's a file in the n2 forums which I couldn't upload here since is 4+ mb's, it has all tsops, the atmega files, flashedit, jeepers and all the instructions you need all in one zip file.

[sukh77]

Usually no signal is cause by eeprom mismatch. Did you edit the eeprom in hexworkshop.
If it is not an exact match on some IRD's you will need to do edit the build config on a flash to match your IRD you can do this in flashedit. Then you will need to edit the eeprom using hexworkshop.

[letor]

hi, i have some problems trying to flah my 2700 ird. first i havent flash an ird before but i read a guide and did this:

jkeys 2.01 flash programming then under chip/sector prog, program and show program at 0x7ff80000? yes checks that flash is not blank continue? yes select my tsop flas and give me a message "error perform flash write request " then "error programming flash at offset 0x7ff80000.

so i cant flash my ird, what can i do? im using a home made JTAG and it can gets all the ird info (boxkey, ird model, etc)

[skinerd]

Usually no signal is cause by eeprom mismatch. Did you edit the eeprom in hexworkshop.
If it is not an exact match on some IRD's you will need to do edit the build config on a flash to match your IRD you can do this in flashedit. Then you will need to edit the eeprom using hexworkshop.

The instructions the receiver uses to obtain the sat signal are in the flash, so a corrupt or mismatched flash will cause the no signal problem, since 301-010 will accept any 301-010 flash and eeprom, I would say the flash is prolly corrupted.

I loaded the 301-010 Atmega flash and eeprom UNEDITED, into an EAED stickered 301, worked flawlessly.

[OldTex]

Tex....how is your 301-013 working? You're the only one I know of that is up and running with a 013.

I put the TSOP into Flashedit, edited the build config to match my receiver, then had it write a new eprom file itself... engaged the VID MOD to fully erase and reflash the TSOP and eprom, reset the VID MOD... and powered it up, let it sit to hunt for sat signal, then connected it up to the dish, had TV...

[4u2dzr2000]

ok guys thanks for the input
I will rewrite both tsop+eepron using flashedit and hexworkshop
then re flash the ird again

back to the table again lol
will report back with the results

[CYCO]

I put the TSOP into Flashedit, edited the build config to match my receiver, then had it write a new eprom file itself... engaged the VID MOD to fully erase and reflash the TSOP and eprom, reset the VID MOD... and powered it up, let it sit to hunt for sat signal, then connected it up to the dish, had TV...

OldTex How did changing the build in flash edit do anything? I have tried all different flashes on 4 different 301.013s and still can't get past the black screen.Can you send me the flash files you are using?Please pm me if you would be willing to send them.Is anyone else up and going with a 301.013?

[jubaitca]

I am getting error 019 on my 301.010 what should i do?

[CYCO]

I put the TSOP into Flashedit, edited the build config to match my receiver, then had it write a new eprom file itself... engaged the VID MOD to fully erase and reflash the TSOP and eprom, reset the VID MOD... and powered it up, let it sit to hunt for sat signal, then connected it up to the dish, had TV...

OldTex how did editing the buil in flashedit do anything.I have tried that at your suggestion and tried several different flashes on 4 different 301.013s and still can't get past the black screen. What files are you using? The ones with all different receiver flashes in thr folder?

[110º]

What about 3900? put 4900 on it and changed build but still no audio... just need the 3900 TSOP to match tomico's flash. Any help would be wicked.

M

don't put a 4900 TSOP on a 3900 ....you know better than that ...

If you don't have a build that matched the provided Atmega TSOP files, then:

--Read your TSOP with Jkeys, save them.
--Run the RSA_Atmega file for your model in Flashedit_beta4.
--Save the modified TSOP files,
--Write back to IRD ..

You don't have to use the provided TSOP files.....modify your own ...!!!!

[sukh77]

Jubaitca - either you didn't program the card correctly or u are using a wrong IRD file.

[jubaitca]

Jubaitca - either you didn't program the card correctly or u are using a wrong IRD file.

Did you have teh same problem? What did you do to fix it?

Because I tried many pfg's and hex and eeprom with the suggested fuse. But still i get error 019.

[letor]

HEEEEEEEEEELP Somebody knows whats happening??

know im trying to flash my 310 010 and give me errors.

using jkeys 2.0.1, flash programming then under chip/sector prog, program and show program at 0x7ff80000? yes checks that flash is not blank continue? yes select my tsop flas and give me a message "error perform flash write request " then "error programming flash at offset 0x7ff80000.

[4u2dzr2000]

ok guys thanks for the input
I will rewrite both tsop+eepron using flashedit and hexworkshop
then re flash the ird again

back to the table again lol
will report back with the results

ok I erased both files and loaded the original files
went to check to see if I had signal coming in
but i get this error (the smart card currently inserted is not valid for use with this receiver) is it because it's been programed with the new n2 file?

[wasup]

You got to open the N2 eeprom.bin in a hex editor and change the build to your own build you saw in jkeys.
The tsop you flash back to the ird must be the one for your model ird.
Ignore this if you know this, just want to help. This is where I went wrong. Now I got three up and running...woot.

[wasup]

HEEEEEEEEEELP Somebody knows whats happening??

know im trying to flash my 310 010 and give me errors.

using jkeys 2.0.1, flash programming then under chip/sector prog, program and show program at 0x7ff80000? yes checks that flash is not blank continue? yes select my tsop flas and give me a message "error perform flash write request " then "error programming flash at offset 0x7ff80000.

You must erase your tsop before you write to it. Keep trying to erase until you have no errors erasing. Then it will write.

[jagged]

Hi, Voila.............she worx! I have been going through alot of reading since this so called Atmega N2 fix came out. I found these instructions somewhere and followed them and I've been watching wide open TV since last night. The step by step instructions can be found at Hxxp:/xxx.chrismyden.com/DSS?stepbystep.txt
You still have to know what your doing, but it was a great help.

[davidasco]

I put the TSOP into Flashedit, edited the build config to match my receiver, then had it write a new eprom file itself... engaged the VID MOD to fully erase and reflash the TSOP and eprom, reset the VID MOD... and powered it up, let it sit to hunt for sat signal, then connected it up to the dish, had TV...

How do you do to edited tsop write an eprom itself?I´m pretty sure That´s what I´m missing

thanks a lot Old Tex

[davidasco]

I put the TSOP into Flashedit, edited the build config to match my receiver, then had it write a new eprom file itself... engaged the VID MOD to fully erase and reflash the TSOP and eprom, reset the VID MOD... and powered it up, let it sit to hunt for sat signal, then connected it up to the dish, had TV...

How do you do to edited tsop write an eprom itself? That`s what I didn´t do

thanks a lot Old tex

[4u2dzr2000]

You got to open the N2 eeprom.bin in a hex editor and change the build to your own build you saw in jkeys.
The tsop you flash back to the ird must be the one for your model ird.
Ignore this if you know this, just want to help. This is where I went wrong. Now I got three up and running...woot.

ok here is what I've done
I have changed both the tsop+eepron to match my ird buld configuration the 4 letter word inside my receiver (CAPD)and load it into my receiver this is what i get ( no signal from the antena )

I have canged both the tsop+eepron to match my ird build configuration the 4 letter word I see in J KEYS when i read my receiver (CAPA) cause those letters are diferent to the ones inside thr receiver and still I get no signal coming in crap

so my ? is there more than one tsop+eepron for the 2700 that i can try or are this atmega fixes the same for all the 2700

if anyone has had the same problem
I like to know what you did to fix it

the only good thing about this is I don't need a hair cut anymore lol

[dtviewer]

I've been fighting the same "no signal" problem on both my 2800's. They both are config CAPD.

[4u2dzr2000]

I've been fighting the same "no signal" problem on both my 2800's. They both are config CAPD.

that's weird
my other 2700 (COAD) worked i am watching tv

but this one is a pain on the ass
do you think is got to do with the build configuration?
that makes two of us having the same problem
maybe a different tsop + eepron?

[dtviewer]

There are a lot of people on other forums with the same problem. But.......
I just came across the fix!!!!!!!!!!!!!! I dont take credit......found on another forum.
In flash edit-under build data (below Build config:i.e.CAPA) the area that says build data MUST match your original TSOP. Min just needed two #'s changed. After that, it sat on aquiering sat for about 5 mins, but then came in!!! I also am getting signal strengtn on the instalation page.
Any questions, I'll stay on here for a while-just ask.

[sukh77]

Did you have teh same problem? What did you do to fix it?

Because I tried many pfg's and hex and eeprom with the suggested fuse. But still i get error 019.
Your problem is you are using a pfg. There is no pfg. Did the directions mention any pfg. Only the hex and eeprom files. then set the fuse to FF AE 89 FF

[gwabitz]

DP301-013 black screen w/headers. 101 and 500 working w/no audio.
Anyone else with a 013 up and running??? (besides Tex).
Thanks

[sukh77]

HEEEEEEEEEELP Somebody knows whats happening??

know im trying to flash my 310 010 and give me errors.

using jkeys 2.0.1, flash programming then under chip/sector prog, program and show program at 0x7ff80000? yes checks that flash is not blank continue? yes select my tsop flas and give me a message "error perform flash write request " then "error programming flash at offset 0x7ff80000.
Just reprogram no big deal. Read the warning that pops up. If you continue to have problems please start another thread describing in detail the problem, and what you have tried. Might get some help if you read the jtag guide at www.bellexpress.vu We don't mind to help. This thread is more about if the fix is working for you or not.

[Smally]

No luck with my 301-013! Just a black screen.

[rookie50]

in the ird folder does the 4900 bin work for a 3900 ird?

[rookie50]

I uploaded the files to sendmefile.com because megaupload is f*cking terrible. Either way now we have more option to download them. Test away!

hxxp://www.sendmefile.com/00143558
in the ird folder does the 4900 bin work for a 3900 ird?

[colin007]

i can get jeepers to read atmega at all it says config problem

[gwabitz]

From what I've been reading, looks like the DP301-013 is a "no go". Except for Tex, where the stars and planets must have been in perfect alignment when he flashed his IRD, then plugged it in...LOL
If anyone gets one going, please let me know. Thanks.

[gary stonecutte]

Just to make sure I have this correct; I have already modded my IRD and ROM10 card which works fine ( watch TV). If i want to try to use the Atemga vs the Rom10 card, I CANNOT use the modded TSOP that I already have in my IRD? In otherwords you have to use a different modded TSOP which only works with the Atmega.

Please let me know.

[gwabitz]

Correct! Use the TSOP for your IRD only, in the TSOPs provided.

[racer69]

Anyone know about the 508?

[OldTex]

OldTex how did editing the buil in flashedit do anything.I have tried that at your suggestion and tried several different flashes on 4 different 301.013s and still can't get past the black screen. What files are you using? The ones with all different receiver flashes in thr folder?


The file I downloaded... It's in the folder marked DP301-13 4 meg flash. Not the two 2-meg flash.

[gap212]

Can someone tell that there were 2 files for IRD, one for TSOP and second for EEPROM. We have to change TSOP build config using flashedit and eeprom thru hex. software. Now there are two other files with ATMEGA too according atmegan2 fix. do we have to change those file build config too before programming to atmega or leave like that????

[simon1]

reprogram your card until it works try different fuse settings
try another atmega
worked 2 out of 3 atmegas with me

[racer69]

Are the 501's and 508's able to use the atmega yet?

[alkasecond]

Just to let you know, for 301.10/3100 just flash the ird with the provided files.
Build CFG and bootstrap DOESN"T matter at all.
In Jkeys go to flash programming, erase flash1(u22), then program it,
next erase flash2(u23) then program, then close flash programing and go to eprom programing and program the eprom .
That's all to it.
Do not exit the Jkeys or reboot the receiver between the steps.
It takes appx~9 min total.

[sifton1]

I have had full guide, but when I tune into channel, got card not authorized. Did check switch-before and after- same result. I decided to read more and found some were using a pfg file in jeepers and some say none needed. Just prog with files provided- seperatly and no full monty. I tried this. Now I get card not valid w/reciever(2700). Any suggestions? Thanks in advance!

[Markman]

anyone know where i can get the RSA_Atmega file for the 3900 model in Flashedit_beta4??

[sukh77]

Time to pay mili for VIP downloads. The files are available in the public files area. Either wait till you can have them or Pay mili for VIP downloads or find them elsewhere. I just wanted tester to confirm. And we have confirmed.

[Markman]

ok .. here is a quick Q...

is it going to make a big problem to flash an ird with a different build?

3900 build CLGA with a 3900 build CLFA

[Markman]

.... clicked twice

[gap212]

After flashing my receiver i was keep getting error 19 and 20 so i reflashed unit again, and now it won't even turned on. What might be the problem...is it dead now or i have to flash again? has anyone exp. same problem...please post ?? thx.

[davidasco]

don't put a 4900 TSOP on a 3900 ....you know better than that ...

If you don't have a build that matched the provided Atmega TSOP files, then:

--Read your TSOP with Jkeys, save them.
--Run the RSA_Atmega file for your model in Flashedit_beta4.
--Save the modified TSOP files,
--Write back to IRD ..

You don't have to use the provided TSOP files.....modify your own ...!!!!

where can the RSA_Atmega file be downloaded?

[gap212]

anyone out there who can answer my post....

[tjh]

Just got my 301.013 (1 TSOP) to work with the ATMEGA N2 fix. everything wide open. Uploaded working TSOP and EEPROM file in the ATMEGA section (if the mods allow it through).
Use FLASHEDIT to put in the 4 letter build of yout IRD into the FLASH bin, use hex editor to do same in EEPROM.
Then load both into IRD, program ATMEGA N2 (you can also use a pfg called WIZARI, if you like)

Have fun!

[smilingjack]

Mods have nothing to do with the files section, we can't even download shit any better then you can unless we pay for VIP

it is automatic

Takes 30 to 60 minutes for the server to cycle them into the list.

[sukh77]

You can post it like I did, till it is in the files section.

[tjh]

I already uploaded this file in a new thread (so people cab easily see it). I wanted to uploaded it again here, but it only alows one upload.

I am just amazed about these people who get this stuff to work!

Good Luck

TJH

[Markman]

hmm..
i got error 19.. a few times and now the box woud't come on :(

hmm

[Markman]

even reloading the orginal eeprom and flash dosn't work :(


i can still access the flash and eeprom.. but the box woudln't come on on power up

[4u2dzr2000]

There are a lot of people on other forums with the same problem. But.......
I just came across the fix!!!!!!!!!!!!!! I dont take credit......found on another forum.
In flash edit-under build data (below Build config:i.e.CAPA) the area that says build data MUST match your original TSOP. Min just needed two #'s changed. After that, it sat on aquiering sat for about 5 mins, but then came in!!! I also am getting signal strengtn on the instalation page.
Any questions, I'll stay on here for a while-just ask.


you are the man dtviewer
thanks for sharing the info
my 2nd ird is finally up and running :)
sheers
keep on testing

[OldTex]

How do you do to edited tsop write an eprom itself? That`s what I didn´t do

thanks a lot Old tex

Open TSOP file you edited with hex editor in Flash edit.. then under scripts, have it write the virgin eprom.

[paulpo]

Is Any Of This For Bev Or Only Dish???

[gap212]

even reloading the orginal eeprom and flash dosn't work :(


i can still access the flash and eeprom.. but the box woudln't come on on power up


I'm having same problem Markman, mine too won't turn on...i think it's fried? Can some tell if there is a way to test IRD i mean using voltmeter or ameter etc.....receiver won't turn on no matter what. I have programmed and it's ready to test, but since there is no power i can't test it. SO please if someone have suggestion, please assist.

[beartrack]

I'm having same problem Markman, mine too won't turn on...i think it's fried? Can some tell if there is a way to test IRD i mean using voltmeter or ameter etc.....receiver won't turn on no matter what. I have programmed and it's ready to test, but since there is no power i can't test it. SO please if someone have suggestion, please assist.


First I need to know what receiver you are working on.

[beartrack]

I'm having same problem Markman, mine too won't turn on...i think it's fried? Can some tell if there is a way to test IRD i mean using voltmeter or ameter etc.....receiver won't turn on no matter what. I have programmed and it's ready to test, but since there is no power i can't test it. SO please if someone have suggestion, please assist.


What kind of receiver are you working on?

[spanky]

error 019 is a problem with the atmega
i have 3 that get error 019 on a 2700 and 3100.010
and 1 that i can pop from receiver to receiver while they are hooked up and running and works fine like the old days

[gap212]

What kind of receiver are you working on?

i have 2800 with tsop and eeprom lock on it....

[paulpo]

is any of this for bev or only dish?

[beartrack]

i have 2800 with tsop and eeprom lock on it....


Did you try using the program wall-v2 to erase the flashes and rewrite? If not give it a try. Also, sometimes when I wasn't showing any power to the receiver I would connect the sat feed to the receiver and it seemed to make a difference getting jkeys to work. I would much rather use wall-v2 than jkeys, has an excellent readme in the zip. When I erase flash with either program, say flash1, after it is erased I reprogram with the new flash before erasing flash2 and also reflash that before writing to eeprom. Hope this helps.

[gap212]

Receiver won't turn on so there is no point using jkeys right...cuz first we have turn it on to get it work thru jtag port...once we have connection thru parallel port we power off IRD and than turn back on to erase or flash the tsop.

[beartrack]

Receiver won't turn on so there is no point using jkeys right...cuz first we have turn it on to get it work thru jtag port...once we have connection thru parallel port we power off IRD and than turn back on to erase or flash the tsop.


Never turn power off when jtagging. You must finish erasing and rewriting before you ever remove jtag or turn power off.

[gap212]

beartrack,
In order for me to use jkeys...i still need to turn on my receiver first...that's what sequence is right....turn on ....unplug it....connect it back..and than press OK.

[paulpo]

wich echostar satellite am i suposed to aim at echo3 or echo1?

[Markman]

ok here is me going crazy.

so my ird didn't want to come on as well, so i erased it and put it in the streem.
well i don;t anything happening its almsot an hour now. :(

Please please can someone help me find out how do i fix this ird.

the light woudln't come on, i tried reflashing with the orginal firmware and nothing.. i tried diffrent firmwares .. nothing .. I even tried earasint the chip and puting it in the streem and nothing.

anyone .. have an experince with this?

[Markman]

ok here is me going crazy.

so my ird didn't want to come on as well, so i erased it and put it in the stream.
well i don;t anything happening its almost an hour now. :(

Please please can someone help me find out how do i fix this ird.

the light wouldn't come on, i tried reflashing with the original firmware and nothing.. i tried different firmwares .. nothing .. I even tried erasing the chip and putting it in the stream and nothing.

anyone .. have an experience with this?

[beartrack]

ok here is me going crazy.

so my ird didn't want to come on as well, so i erased it and put it in the stream.
well i don;t anything happening its almost an hour now. :(

Please please can someone help me find out how do i fix this ird.

the light wouldn't come on, i tried reflashing with the original firmware and nothing.. i tried different firmwares .. nothing .. I even tried erasing the chip and putting it in the stream and nothing.

anyone .. have an experience with this?

Please read my post about the sat feed carefully. What I meant was lease it hooped up to your receiver while your using jkeys if you have a power problem, it may help let jkeys erase and write.

[Morpheux]

ok here is me going crazy.

so my ird didn't want to come on as well, so i erased it and put it in the streem.
well i don;t anything happening its almsot an hour now. :(

Please please can someone help me find out how do i fix this ird.

the light woudln't come on, i tried reflashing with the orginal firmware and nothing.. i tried diffrent firmwares .. nothing .. I even tried earasint the chip and puting it in the streem and nothing.

anyone .. have an experince with this?

It wont receive anything unless flash u23 is written to it and the light turns on.

[mruk69]

Too bad i can't use my own cam id and rec. id, my 2800 is subbed to Internationals only. It is a shred sub and I don't want to fuck it up. As i have to keep the subbed card updated. I wonder if there is a a way around this.

[reb43]

markman, I had that problem for two days, if I were not almost bald now I would have pulled my hair out, but I used wall not wall2 to write the u23 bin then the 22 bin then programed my atmega and lo and behold it works. Finally. Makes you feel good when it all comes together, keep trying.

Wall has a step by step instruction with it, download a copy and try it, I also used wall to write to my receiver, I am using 301-010. Channel changing a little slow but I can live with that, I am watching TV

PS: Erase flash (each) first then program new flash to receiver, should work, if the message does not say "writing" something is wrong, restart write flash and try it again.

[erotic1]

anyone with tsop flash for 3900?

[gap212]

can someone please let me know how can i test my receiver, it won't trun on. it is 2800

[nek]

I've been up and running for 2 days but I have a problem.
Every 20-30 minutes I go black screen and then aquiring sat comes up, goes through 1-5, the guide downloads and I'm running again.

I've loaded everything OK, followed all instructions, and reflashed with files from different sites to eliminate corrupt files.

301.010 EAED
jumpered atmega original EFA
buffered jatag

Any suggestions are appreciated.
Thanks
nek

[davidasco]

Open TSOP file you edited with hex editor in Flash edit.. then under scripts, have it write the virgin eprom.

did you edit only the four letters of your build in config in hex editor or some other data so it can match your build in configuration? because I only change the four letters to match my build config and I edited it in Flashedit

[shopright]

beartrack,
In order for me to use jkeys...i still need to turn on my receiver first...that's what sequence is right....turn on ....unplug it....connect it back..and than press OK.

some ird's won't show power on just jtag with ird pluged in if it see's tsop it can be fixed.

[500 MG]

I m trying to reflash my ird and it wont let me do it and i m getting this message "JKeys Error - LSI control unavailable, using slow programing" whats that mean? i got 301-010.

[udntcme]

There is what is being call The "Black screen fix on another site for single tsop reg 13 actually the site gives directions to a google search .Supposed to fix Reg 13 single black screen someone can pm me and maybe we can post it here.

[smilingjack]

I m trying to reflash my ird and it wont let me do it and i m getting this message "JKeys Error - LSI control unavailable, using slow programing" whats that mean? i got 301-010.


That means the entire flash is corrupted including the boot sector which never gets erased.

The boot sector has to be replaced using wall2 to get it loading at normal speed
Read the wall instructions on re-flashing this section (the first 60,000 bytes)
Then erase & re-flash the entire TSOP at normal speeds (3 min each)

[gap212]

some ird's won't show power on just jtag with ird pluged in if it see's tsop it can be fixed.

Can you tell me do we have to turn on the receiver while flashing the tsop to receiver or it can be done without it. Cuz won't turn on...and i tried so many time now but won't work.

[clauderacing1]

is this work whit bev

[clauderacing1]

is this work whit bev?

[erotic1]

looks like both copies of flashedit beta 4 on this site are corrupted archives! Also for those looking for 3900 flash try this:

h**p://www4.rapidupload.com/d.php?file=dl&filepath=6049 (http://www4.rapidupload.com/d.php?file=dl&filepath=6049)

[Filo]

There is what is being call The "Black screen fix on another site for single tsop reg 13 actually the site gives directions to a google search .Supposed to fix Reg 13 single black screen someone can pm me and maybe we can post it here.

I am having the exact problem. Can you PM me the directions or site....please....

Thanks

[OldTex]

OldTex how did editing the buil in flashedit do anything.I have tried that at your suggestion and tried several different flashes on 4 different 301.013s and still can't get past the black screen. What files are you using? The ones with all different receiver flashes in thr folder?

I start with that -

Jtag 301-13, and save it's TSOP - note it's build.. DAHC, what-ever.

Then open the 301-13 4 meg TSOP fiel in flash edit, edit the build config you got from JTAG. Save this. Then create a virgin eprom file using flash edit.

Connect VID Mod, Jtag 301-13, erase flash, program, program eprom, shut off JKeys, shut off IRD, disconnect VID MOD.

Connect to TV, leave ATmega out for a bit. Make sure you get searching for Sat Signal. Insert Atmega, make sure no errors. Let it sit a bit, then connect up sat cable, run check switch, watch TV.

[steindude]

THANKS!!!!! Skinerd,SJ, Sukh and the rest. 2 each 301.013's up and running.
The read me file missed a crucial step. EDITING the flash as well as the EEPROM to match your build config. That made the difference for me.
The original file in the N2 Hack zip did not work either. The one from Hashhu worked like a charm.
AGAIN thanks to everyone who has contributed.

the "Dude"

[OldTex]

How do you do to edited tsop write an eprom itself? That`s what I didn´t do

thanks a lot Old tex

In flash edit, beta 4, with the TSOP BIN open, under scripts, you should spot one that says "Create Virgin Eprom"... run it.

[gwabitz]

Can you tell me do we have to turn on the receiver while flashing the tsop to receiver or it can be done without it. Cuz won't turn on...and i tried so many time now but won't work.

The light doesn't always come on when you Jtag, and you don't need to push the power button everytime either. Just plug it in, so that the circuit board has power. Are you getting any info in Jkeys screen when you Jtag it? If you are, then that means evrything is OK. Try erasing the flash again, then try programming it again. I have myself an ignorant 301-010, that keeps telling me (when I try to program the flash) that a certain 0x7fff..whatever is "limited" for programming, so obviously I didn't erase the flash fully or something. I'll have to try Jkeys specifically for the 301-010 or better yet Wall. My power light also doesn't doesn't come on, but it still "reads" in Jkeys, so I know I'm good to go. Hope this helps you out.

[erotic1]

both versions of flashedit beta 4 on this site are corrupted. Can some upload a working version please! This is killing me! Thank you!

[clauderacing1]

isthis work for bev????

[OldTex]

Just FYI - (Please do not PM me, just grab the files)

Everything is out there to get your 301-13 going. I have gotten 5 (FIVE) 301-13s going today for friends. All channels open, PPV, porn.

Read, read again.

For the 301-13, you WILL NEED the VID MOD connected. If you do not know how to do this, download the instructions located here and everywhere else on the 'web.

I repeat, the VID MOD will allow all the flash to be erased, and reloaded. Without this, you'll get problems.

[gap212]

The light doesn't always come on when you Jtag, and you don't need to push the power button everytime either. Just plug it in, so that the circuit board has power. Are you getting any info in Jkeys screen when you Jtag it? If you are, then that means evrything is OK. Try erasing the flash again, then try programming it again. I have myself an ignorant 301-010, that keeps telling me (when I try to program the flash) that a certain 0x7fff..whatever is "limited" for programming, so obviously I didn't erase the flash fully or something. I'll have to try Jkeys specifically for the 301-010 or better yet Wall. My power light also doesn't doesn't come on, but it still "reads" in Jkeys, so I know I'm good to go. Hope this helps you out.

thx gwabitz....i understand that power light doesn't have to turned on, but my circuit board is getting no power. That's what my confusion is and i'm trying to work it on from morning. What would be wrong my IRD is fried or what...is there a way that i can check it out using voltmeter or ammeter etc. Is my boot f'k up or what...how can i fix it???

[gwabitz]

Can you tell me do we have to turn on the receiver while flashing the tsop to receiver or it can be done without it. Cuz won't turn on...and i tried so many time now but won't work.

You don't have to push the power button everytime you use Jkeys, and the power light doesn't always come on either! Just make sure it's plugged in so that the circuit board has power to it!
Are you getting a reading from Jkeys like IRD #, Box keys ect? If so, then you're good to go! I myself have a ignorant 301-010 that keeps giving me a pop up window that 0x7ff..or something is limited for programming, so obviously I didn't fully erase the TSOP. I'll have to try Jkeys specifically for the 301-010 or WALL, but I'm still getting readings from Jkeys which means I'm still OK. Hope this helps you out.

[gwabitz]

Hey maybe I double flashed my TSOP just like my post LOL. Anyways gap you should be able to get some kind of power reading off the board. I'm a bit confused. You say your unit is dead, yet it sounds like you're wondering about using a meter to test. Did you test the board for power?

[gap212]

No i'm not getting any reading from Jkeys...yesterday when I turned on my IRD and followed the step for jkey like turn on IRD...once detected....switeched off...and than press OK, it worked right away. Today when it is not getting turned on ( i mean internal circuit board) not the power light i'm having tough time retreiving flash. try so many time but no go...that's why i'm asking does the ird have to turned on (internal board atleast ) inoder to flash the tsop to receiver.

[joshwild]

can someone please let me know how can i test my receiver, it won't trun on. it is 2800

It is really hard to screw up a 2700 or 2800 model receiver, they are the easiest for anything, my advice erase the flash, load on one that you know works and if the receiver works. load on the atmega flash, i loaded it on 2 2700 and they work fine

[gwabitz]

I would think so. That's most likely why you're not getting a reading. You should post your problem seperatley for people to help you out, and save this thread for the "atmega test " replies. Best of luck to you. You'll figure it out. I always do....eventually.

[Markman]

First, Thank you all for your help
Wall V2 actualy worked ! I couldn't do it with out all your help.

wall v2 .. said erasing faild but.. i did it again and again and well it just stop giving me the error.
so i reprogramed and it worked :)

got the Atmega to run too .. and watching tv now.

-------------
erotic1 ,

i use 3900..
you can get a few diffrent 3900 builds at
rom10x..
change the build to the one on your ird.. and change the build in the eeprom for the one on your ird.. and it will work.

good luck.

[udntcme]

"Reg 13 single" Here's what i'm doing ,I have flashedit beta 4, I loading 4meg tsop that is posted in the latest files, I changed build config "and" build data and checked to make sure they changed and checked the bk's were starting with 5254(The correct tsop)...created a "virgin eep" Erased and loaded these perfectly. loaded the atmega with the hex and eep files and made fuse bytes FF AE 89 FF anyone see anything wrong with this maybe the fuse bytes...? cause I cant get vid or sound exept channel 101 I get vid only Little help please.

[udntcme]

I checked ecm fix for the flashedit scripy ...are the RSA key's included with the Tsop already or do we have to install them. Thanx.

[propellanttech]

I will say I just finished resurrecting my ird with the atmega 128.

I have to admit that I didn't get the tsop or eeprom files from here...but I will verify that it can be done.

I would post the files that I used ..but I would want them to be public.

It does freeze a little...but not much and it tooka few tries to get it to work, but here is another one to add to the list.

I think this is my first post here...but I post else where mostly.

Thanks,

Hope this helps,

Proptk

[STP]

I'm having trouble trying to do a 301-10. I've followed the instructions, and let the ird sit for 20 min, put in the atmega let it sit, hook up the sat cable and bang it acts like it's downloading.

I can't turn it on, can't turn it off until if finishes blinking, an then all I get is the pre view channel and the rest all black.

Anyone have any idea what i'm doing wrong?

Thanks
STP

[gwabitz]

I'm up and running on a 301-013!!!! Twostep just posted the link in the forums.
I've been battling with a black screen w/header for two days. I didn't know sqwat about hex edit, and still don't, But I found these files complete ready to go, no editing of any kind involved and presto....TV land!!! I can't believe my eyes. I had to turn to the porn channels just to prove to myself that it indeed is wide open. Thanks to all involved!!!

[gwabitz]

Here's a stupid question. Can you shut off the IRD with this fix, or is it like the AVR-X, where you have to have it "on" all the time? Thanks

[k0ke]

another sucessful story with a happy ending

[udntcme]

And what forums would those be please ,we have quite a few here .Thank you.

[k0ke]

the ird (reciever) has to be plugged in for you to jtag it, even tho the power lite isn't on, internally the unit is actially on, so yes, you need it plugged into a/c whole you jtag

[udntcme]

Gwabitz ,Thanks bro found it. A little tired after "Beating " on this 13 single for the better part of this day.Been reading that the files out all over the place for reg13 single don't work.So this is good new's...all the best...!