black screen

[rykrishell]

Hi Just modded my 301.10 everything looks ok but only getting preview channels all the rest black screen ? using atmega 128 do i need to start over ?:confused:

[spanky]

check your mod to the tsop make sure u got proper build with the right bk and ird# and that they match the card

[hads]

check your mod to the tsop make sure u got proper build with the right bk and ird# and that they match the card

what do you mean by match the card? im havin same problem and checked jkeys and all right and on the atmega there nowhere to put boxkeys and ird just program the hex and eprom and fuse bytes

[udntcme]

You guy's need to understand "ONE Thing" and ONE thing only....There are mods for your ird's and A hex and A eep for your atmegas.There are BOXKEY's and IRD NUMBER's on The MODDED TSOP"S that need to match THe MODDED HEX AND EEP of your ATMEGA"S I CAN SAY NO MORE ..(sorry for screeming) ssshhheeeezzzzz...I'm otta here...Good luck all the best Peeps.

[udntcme]

and if the key's changed as i was trying to help you can chew my ass...LOL ...hehehe.

[hads]

you can yell all you want but how the hell do you modify the hex hex and the eeprom eep i thought they were already modded for the 52542bd807dcec6f box keys and the R00-4779361-67 ird

[udntcme]

Just had to add this there is a post about a guy changing the build to "SHIT" and it worked .there is a build data box in flashedit under the "build config if you change the build config all you need to do is click on the build data box and it will auto change the build data to match the build config.....check it out.

[udntcme]

All the Atmega hex and eep now in the files section should have the bk's and ird#'s that work with the same tsop build's for the listed ird's.Some may not be useing the rite tsop's check in flashedit the bk's should start with the number's 52 54....

[hads]

you mean open the hex hex and the eeprom eep in flashedit cause itryed and it dosnt reconize them ,ive tryed atmega files from diferent sites and same thing ,thanks for the patience though

[udntcme]

No, the hex and eep are for the atmega card...Open the tsop for your ird in flashedit check to see if your box's build config is close to the one you opened in flashedit you can change it if you want (but I don't think it even matter's) if you do change it go to the box rite under it called data build and just click on it and it will adjust your build config automatically.then save , then go to aply script and you can make the correct eep to match your build config.then write these to your ird useing jkey's.

[udntcme]

Feeding frenzy...holy s**t ...!I'm taking a union break...!!!

[hads]

ya i did all that twice and tryed 5 different atmega programs from different sites still black screen

[udntcme]

One last thing at the top of this page if you have not tried already there is a "all in one" package...this should work you should not have to go all over looking for tsop/atmega combination's to put together this all in one should work fine I've used these and they work make sure your fuse byte's in jeeper's don't start with "FC" your fuse byte's should be FF AE 89 FF. Are you sure your useing the rite tsop to flash your ird with...? are you sure your ird is taking the flash...?There is something very obvious here and when you find it if your like me you'll be kicking yourself ......That's all I got.

[udntcme]

Damm , have you done this...? have you read back your tsop to see if it's taking...? do a read in jkeys and save then open it in flashedit too make sure .I'm clueless at this point keep trying It has taken me day's to fiqure out crap before.All the best bud.

[rookie50]

had same prob on one dp301-010. After flashing I would plug in ,green led comes on for a couple sec then out nothing!!! Tried flashing with every Tsop listed as good. Finally this worked.
1. loaded with U22 and U23 flash from files for the DP301-010.
2. Now I erasewd SA3 from flash1
3. Hooked up to sat cable with power on and Atmega in and let it restream
4. Reflashed U22 and U23 from files, don't touch EEPROM though
5. hooked back up, did check switch and it worked

P.S. the streamed software was at P243 so I used modded files at P243 for U22 and U23

[patricig]

For the plastic programming, you say the build config needs to be matched on the tsop but i've read that if the first two letters are the same you are good. I can't find a tsop for an EAED build and had to use EAEA tsops. Even the tsop on my box was EAEA. Still doesn't work and has black screens. This is so frustrating.