301.10 light wont come on after mod

[hads]

i erased both flash 1 and 2 and did full erase and reprogrammed u22 and u23 with modded file then programmed the eeprom with modded eprom then i plugged into wall for 5 min and connected the sat wire and all i get is black screen with no green light on ????????any ideas was i suppose to do a full erase or just write the new modded tsops over the old ones, should i write my saved tsop back on and just write over it?????????????

[bobsmith161]

ok:D
start jkeys and erase flash u22,u23 both 3 times each then program u22 1st next u23 then eeprom
download (atmel128) for the files you need
p,s if it don't work try changing the buld config(both flash & eeprom).... also if you reverse the buld config if the eeprom it will soft lock the 301-010 and should not up date software:cool:

[yahoo]

ok:D
start jkeys and erase flash u22,u23 both 3 times each then program u22 1st next u23 then eeprom
download (atmel128) for the files you need
p,s if it don't work try changing the buld config(both flash & eeprom).... also if you reverse the buld config if the eeprom it will soft lock the 301-010 and should not up date software:cool:

I did not know that if you revers the build config it will soft lock it

Thanks for the tip

[mad max]

flash 1 is u22 and flash 2 is u23 also when you save flashs don`t forget to save both, use pull down box in jkeys first screen

[Stocko]

After writing back your original eeprom and flashes ( to stabilize the ird), try your programming again by erasing flash 2 first and writing U23 to it. Next, erase flash 1 and write U22 to it. Then, write the new eeprom over the old one, no erase. Next, save your eeprom and when the screen pops up asking where to save, reverse the build config and save file. Next, re-write the modified eeprom and the programming should be done. Plug in the ird but do not hook the sat cable up for 10 minutes, then connect sat cable and you should be ready to go.

Stocko:cool:

[hads]

i tryed programming in wall 2 and wont program the flashes ,, it says it does but when i go to read its still screwed and green light wont come on, when i try in jkeys it keeps giving me errors about unreconized and toggling any ideas,im a twit and yes i would screw up the lords prayer

[#40Fan]

What kind of JTAG are you using? Simple or Buffered? How long are the leads?

[bobsmith161]

What kind of JTAG are you using? Simple or Buffered? How long are the leads?
i have found that the buffered work best for me. i have buld the jtag as a daughter board on top of the jtag pads with stand off's about 1/2 inch then the port for the computer.:D .....i cant stand the push pin one's.....hoo...hmm i think i will hold the jtag......dam i moved???????tsop is corrupt.....:eek:

[kwizzler]

i tryed programming in wall 2 and wont program the flashes ,, it says it does but when i go to read its still screwed and green light wont come on, when i try in jkeys it keeps giving me errors about unreconized and toggling any ideas,im a twit and yes i would screw up the lords prayer

Be sure you are not installing the TSOPs backwards. In Wall, Flash 2 goes at 1FC... and Flash 1 is at 1FE... If you can get your original flashes loaded correctly, then don't erase both flashes at the same time anymore. Once the flashes are loaded, you can use JKEYs again and then try erasing and loading Flash 2 first and then erase and load Flash 1 after that.

[hads]

im using a push down jtag not buffered and i tryed the reserection with the 60000 byte in wall 2.0 and the green light still wont come on it says R0000000000000 and boxkey is 00

[dssdish]

]I Need Some Help Newbie I Have 301.13 u12 tsop receiver it Already Mod with a lock I Know ird Box Key Also I Have Atmega 128 Prog don't have a jag what can i do to start watching some tv plz advise thanks

[hads]

k i got it all loaded correctly finally and comes on and now when i put the atmega in all i get is previews and black screen on all others ,what is wrong now