which t911 is this?

[ShapeShifter]

This is an old t911 that I used for p3s... All of the t911's I've seen here are either black (nexus) or green. Which is this? Can I mod it?

[Cimba]

This is an old t911 that I used for p3s... All of the t911's I've seen here are either black (nexus) or green. Which is this? Can I mod it?


Yes it can, it is a T911 blueboard and I have pics of the mod; will try to attach.

[ShapeShifter]

Much appreciated...

[JCK7]

AND absolute 1
is same board

[nipa]

any one konws how to mod this hu loader for dishnet card?

thanks

[beartrack]

Well I'm stumped. I have an old T911 that someone gave to me modded and it takes the flash fine but when I run vcc analyzer I get no good returns from it, doesn't matter what switch I open. Tryed 1&5, 2&5 makes the script error, tryed just 1 and just 5 no go. Even tryed rewiring thought it might be a broken wire, notta. It's reading the card cause when its running and I pull the card out it goes from ?????? to XXXXXX. Still 0% on everything. Thought it may be the trim pot and replaced with a 2.2 resistor, same. If anyone's got any ideas I'd be glad to here them

[sugadaddy]

Anyone have a mod for a KickAss Clone blue board or a White Viper ??

[LittleE]

A friend of mine has a old absolute sitting around collecting dust.....Can that be modd and is there a how to do it file flying around I could use to do the modification...............Thanks In Advance

[ROSCOE]

I have one of Mili's 3 in 1 / All in One loaders that I bought about the time God was seperating the light from the dark. Anybody know if this is the same as a T911 or some other model that I can mod?

[LittleE]

Ok I found the pics of the mod absolute 1.....I am giving it to the wife to take to work in the morning to do the mod.....Great having some one in the family that a does printed cuircut board work for a living.....I was looking at the board for the pot to turn to increase the amps during glithing I didnt see any thing that could be turned......Do I need to buy an external power supply or do I use the ps2
Thanks in Advance

[LittleE]

any takers on this topic

[The Specialist]

Yes it can, it is a T911 blueboard and I have pics of the mod; will try to attach.


Thanks Cimba, why cant I see the trimmer Pot in your pictures, or dont you need one with that loader??

Thanks
TS

[ShapeShifter]

Thanks Cimba, why cant I see the trimmer Pot in your pictures, or dont you need one with that loader??

Thanks
TS

Its shown there -- its in the topside picture, by the LEDs. I have all the parts, so wish me luck tonight.

[Cimba]

Ok I found the pics of the mod absolute 1.....I am giving it to the wife to take to work in the morning to do the mod.....Great having some one in the family that a does printed cuircut board work for a living.....I was looking at the board for the pot to turn to increase the amps during glithing I didnt see any thing that could be turned......Do I need to buy an external power supply or do I use the ps2
Thanks in Advance

The one in the post I did has a plug in for an external supply, usually 9v + tip adaptor, I'm not sure with the ab1 if its 9 or 12 v.

[das]

the traces around u2 are different than yours does it look like
I would need to do a different mod if so have you seen one like it
also over between u6 and u7

[shady]

the traces around u2 are different than yours does it look like
I would need to do a different mod if so have you seen one like it
also over between u6 and u7

I have the same question as das...My board is black in color with the same differences that das noted. It is marked on the back "unlooper & unloader 200" as well as "dishpal.com"

Thanks

[shady]

Heres a couple pictures of mine. I have further detailed pics if needed.

[The Specialist]

I am still a little confused (maybe its just some of the mixed terminology), I want to follow Cimbas post on modding the blueboard T911, but when he refers to a switch on the diagram, what type of switch is it? Also, is a 5k trimmer pot just good for unlocking R10's, and is it too powerful for 102's? Looked everywhere for a parts list to do the T911 Mod, just couldnt nail one down.

Thanks
TS

[hugh]

Hi,
I have an older unlooper, which doesn't match any of the pic's here.
My unlooper is etched "time card reader" and originally was a H card unit.
All chips are DIP type, but I think the t911 etc is the same circuit ,or close, just newer. With schematics, I can figure this out, but not based on the pictures alone. Anyone have the schematics??
Thanks.

[dogg]

can anyone tell me what loader this is thanks

[Cimba]

Very similar to T911 blue board but some differences, try searching thru the many pics posted in the Sticky for loader mods in this forum.

[dogg]

this is the first 1 i have seen i have 2 different t911's and this 1 close but no cigar ! :}} thanks cimba

[The Specialist]

Thanks Cimba have now completed the mod like your diagrams posted, would like to test to make sure its working properly, I have managed to flash the atmel fine, but cant seem to test the functionality of the trim pot, I have my multimeter on one leg of the trim pot and the other on the metal case of the Db9 socket (ground) and get no reading.....does that mean its installed incorrectly?

Thanks
TS

[jpc314]

can anyone tell me what loader this is thanks

looks like mine, some say it is a aftershock, but the pic i found was a little different on the backside, top was exactly the same and the back was too except 1 little spot. will post mine later, maybe someone can help us.

[COMODO]

Any step by step descriptions on HOW TO MOD T911
Thanks in advance!!!

[COMODO]

Any step by step on HOW TO MOD T911 exept pictures.
Thanks in advance!!!

[Sunkist]

Cimba,
I am looking at your pics as I have the same blue board. I have a couple of questions. I would assume that none of the pins on the chips need to be raised since you have cut the traces here and there?? On the removeable chip (2313) is it best to raise the chip and put the wire in the slot when you replace the chip or just solder to it as is?
Thanks
Yes it can, it is a T911 blueboard and I have pics of the mod; will try to attach.

[spyder98]

the traces around u2 are different than yours does it look like
I would need to do a different mod if so have you seen one like it
also over between u6 and u7

Dass where you able to mod this unlooper? I have one the same and wanted to know what is needed to mod it .
Thanks,
Spyder98

[spyder98]

Has any one done one of these with the diffrent traces ?

[das]

no I messed it up guess Iam not as good at soldering as I thought

[GallDurnit]

Anybody modded one of these? Surely there has to be a schematic on the T911 clone modification somewhere. One solder run keeping me from doing the mod!!!! The original has a good write up but a different chip set. I've got a 311 with a ISO attached getting a ATR just waiting to be glitched into. Like everybody else just trying to use some of this old stuff to get going.

[toomanykats]

there is a post in this forum 4 weeks ago started by normsfirebird about this loader that i posted how to mod the red board rev b. mine is not red but otherwise identicle.

[spyder98]

Ok modded my t911 and all i am getting is -------------------never any + . I have tried with a 2.2k resister and with a 5k pot. could some one please help.
spyder98

[spyder98]

the traces around u2 are different than yours does it look like
I would need to do a different mod if so have you seen one like it
also over between u6 and u7


Just to let you know that I was able to get it working by doing the modd exactly as descibed except using a 25 ohm trimmer Pot. Works great opens them in under a minute and a half.
Spyder98

[troc]

Dogg the name of that loader was a Blaster unlocker.

[sukh77]

Any way to mod the T911 greenboard for the 4619 chips?

[nj2004]

Hello
I have been searching for a mod and cant seem to open any pictures at all.
Could someone please help and let me know where i can see the mod pictures or email me .
Much appreciated.
NJ