Woot Woot..!

[Cid6.7]

Glitched into my 1st 102 with my modded T-911..!!

[lightning0009]

I'm still trying and getting NoRsp+-NoRsp+-NoRsp+-NoRsp+-NoRsp+-NoRsp+-NoRsp+-NoRsp+-NoRsp+-NoRsp+-NoRsp+-NoRsp+-

Any ideas? I'm using my kickass clone H card modded unlooper. I did a 101 last week.

[alwayswatching]

is there any where i can buy a modded load some place secure i went to milis store but i didnt see it
thanks in advance

[udntcme]

This after two hours I adjusted ..or fine tuned the pot and changed some setting in winex...but still no go. Any suggestion's...?..Keeps running like this with the ocasional "NoRsp"...? Let the 102 Glitching continue....
LETS TRY NEW DELAY
Glitch Delay = 0395
VCC = 1C

+--+-+--+-+--+-+--+-+--+-+--+-+--+-+--+-+--+-+--+-+--+-+--+-+--+-+--+-+--+-+--+-+--+-+-NoRsp+-+-+--+-+--

[udntcme]

Lightning0009....Try changing the "Byte Delay " to "10".

[beartrack]

Got one to open in 16 minutes with a modded mikobu, start 320, limit 350 everything else left stock. Replaced the resistor with a pot and turned way down till see errored out then turned it back up just a hair and restarted the script.

[udntcme]

[QUOTE=beartrack]Got one to open in 16 minutes with a modded mikobu, start 320, limit 350 everything else left stock. Replaced the resistor with a pot and turned way down till see errored out then turned it back up just a hair and restarted the script.[/QUOTE I'll try your setting's I'm useing a mik 3...(let ya all know).

[norton]

is there any where i can buy a modded load some place secure i went to milis store but i didnt see it
thanks in advance

looking for the same thing

[Crazy1_79]

Yo Cid, I temporarily lost my internet for awhile, but do you uhhh, YAHOO!!!, May need a few pointers on the 102 glitching you glitch king you! How in the hell am I suppose to make any dough glitching cards if I can't get into my own???? I know you're soaking up all the profits if I don't get my ass in gear.

[Cid6.7]

LOL Crazy1 wondered where you went never see you online anymore..
Yah I popped the rest of my cards today easier then rom10's now ;)..I'ma little sketchy in the 3m's out tho heard peoples havin troubles...I'll wait & use my R10's untill the kinks are worked out..

Went & ordered a nexus this morning...While fine tuning my T-911..Now I have no use for the nexus..LOL

[joesnuffy]

I don't have the script right here in front of me so I don't know the name but try adjusting the last value that starts as .5 and is suppose to adjusted to 1.2 high. Its the value that is used to refine the +-+-+- . I have noticed by playing with it you can also get rid of the No Response values or reduce them. If your on .5 try going below it to like .1 to get rid of the No Response values. This advice is assuming you have adjusted your pot to get to +-+-+-. I have noticed that you need to get to +--+--+--+-- the double minus works better.

I have dialed my Mik 3 to the point I have succesfullly cloned a rom 102 and its working. Gotta like that autoroll.
Joe

lightning0009 (http://dssftp.com/forum/member.php?u=13883) Offline vbmenu_register("postmenu_321301", true);
Registered User
Join Date: Dec 2003
Posts: 140


I'm still trying and getting NoRsp+-NoRsp+-NoRsp+-NoRsp+-NoRsp+-NoRsp+-NoRsp+-NoRsp+-NoRsp+-NoRsp+-NoRsp+-NoRsp+-

[Crazy1_79]

LOL Crazy1 wondered where you went never see you online anymore..
Yah I popped the rest of my cards today easier then rom10's now ;)..I'ma little sketchy in the 3m's out tho heard peoples havin troubles...I'll wait & use my R10's untill the kinks are worked out..
Went & ordered a nexus this morning...While fine tuning my T-911..Now I have no use for the nexus..LOL
I got it figured out, it would of been nice if you would have mentioned the low ass resistance at the pot. I actually had to wire resistors together to get mine down to 12 and a half ohms, my 15 turn 1k ohm adjustable pot got so damn hot it was melting the hot glue I have holding it to the case of the loader, then it would error out the script, probally because the pot failed at that kinda heat. I've gotten into all three, but my rom 102, rev 105 won't take the 3m patch, can't get a read on it, errors out, the other two were rom 102, rev 103 and they both took it, just getting black screen on a 2800 though, will test on a 301 and get back to you cid. sorry I ain't been around much, I will get the internet back on at home here around the first probally.

[woods]

ya i got into 2 of my 3 about 1.5 weeks ago. looped one of them in the fine tuning process. oh well all in the name of testing. i can give you pointers on the 102 3m's. i have one programmed and autorolling.

woods

[sukh77]

The 102 that I have all I get is the top 180 package or something. No ppv, No porn, No international. I think my 102 is rev 105.

I would like to start testing tiers, compare them, and also I want to get the address's figured out for nagraedit, instead of making changes in hexeditor. Then possibly make a patch instead of using someone else's bin.