Loader Mods

[Cimba]

Mikobu 3 mod.

All explained here along with the pic. http://www.dssftp.com/forum/showthread.php?t=44611

[Cimba]

These are the pics for one of the blueboard T911 mods which often is the same as the greenboard mod.

http://www.dssftp.com/forum/showthread.php?t=52830

[OSTthug2k]

Anyone Have pics or info on how to mod a T6?

[Cimba]

Download file and change .txt to .zip

[2getwired]

any mod for a UL Pro........i realize it burns coal for power but i have to ask.

[Cimba]

Never heard of it but ya never know, will look around.

[Double^D]

how about a scorpion pro

[LittleE]

Hi folks was wondering if there is a guide out for the ABSOLUTE 1
Thanks in advance

[Cimba]

I read a post that said the board was the same as the green/ blue board T911 but don't know for sure. Check the pics in the Sticky and compare to your loader. Go to this page and you will find it there. http://www.dssftp.com/forum/t40558-p5-modded-loader-how-to-guide.html

[Cimba]

If anyone knows the name of this please post. Download and change .txt to .zip .

[wyochimneysweep]

ulpro would be nice i got one too

[Reabo]

How about cracker's ultra repair station?

[dishrag]

Hey Cimba mod for Detonator II ??????

[lefty]

If you come across anything for the Intek SCRT - I'm game.

[Bandit5906]

Download file and change .txt to .zip


How does one change the file extension from text to zip? I hate to admit my ignorance, but I'd rather admit I don't know and find out how than to remain in the dark.

[Cimba]

Once you download the file right click on it and from the list of options choose rename, delete out txt and type in zip and click on the desktop. It will ask you if you are sure you want to change it and you click yes, Bingo !

[Bandit5906]

Once you download the file right click on it and from the list of options choose rename, delete out txt and type in zip and click on the desktop. It will ask you if you are sure you want to change it and you click yes, Bingo !

Thank you: I am humbled!

I've changed file extensions via MS, but knew there was a simpler way!

[kelowna_pitboy]

i need the flash files for a t911 using xpatmel. the newd12 is missing files. pleeze help.

[mrxxxx4]

Any one have instructions onmodding an extreme HU sureshot? came from cyber labs
thanks

[sam111]

My friend has a T-6 but does not have dip switches on it.
Is it useless to mod?

[ipdaly]

Looking for modding details for Detonator ll loader??

[lightning0009]

Detonator II mod trying it now.
C&P
Here's a pics of the orginal mod. After trace'ing out the detonatorII a bit I found that 74HC00 (3b) is being fed from the block via the 3rd-74HC0053 Pin-15 located at U11 on my board. So I decided to connect the 74HC00-2b to U11 pin-15 instead of connecting to Pin-2 of the 74hc04. I found that this minor mod seemed to improve my glitch rate success, all credit goes to the orginal creator of the mod.
Good Luck satvia

[2wayradio]

Hi i have a Detonator4 loader that is slightly different then the detonatorII. would the modder be the same..also what flash do i need for this to work on Rom 10's
rev23 & 24..also 2 Rom 11's. really new at this and could use a step by step instruction how too... THANKS 2wayradio

[iso_loco]

I also need to find a UL Pro Mod... Give me a reason to wipe the dust off it :D

[spert]

Lefty - I guess we are SOL on the Intek? I do have some info on a loader that is kind of similar, but I'm not enough of a schematic wiz to figure it out. I can send it to ya if you like?
LOL - Nevermind, I sent it to you already (the memory is the first to go!)
Did you have any luck?

[pasor]

Do you have anything for 911 blue board?

[lefty]

Lefty - I guess we are SOL on the Intek? I do have some info on a loader that is kind of similar, but I'm not enough of a schematic wiz to figure it out. I can send it to ya if you like? LOL - Nevermind, I sent it to you already (the memory is the first to go!) Did you have any luck?

Haven't been able to check it out yet. Busy busy ya know.

It does seen that nobody has even tried the SCRT.

Glad I got mine virtually free.

[digerman]

can someone please help im tryin to mod my det 2 i lifted the pins on hct 00 do i have to lift the pins on hct 74 and hct04 too?
thanks digerman

[Ronaldo]

Can anyone give me the pinout for the UL Detonator Ultra I have a unit with the end cut off of the cable .......it had a usb plug on it as well but I don't care about the usb if someone knows the answer to this problem you will save me a LOT of time and Iam sure headaches

[sillywilly]

This is a green board with a 4-position red DIP switch. Any info re Mod with picture would e appreciated. Tnx in advance.

:D

[Cimba]

Do you have anything for 911 blue board?
How far did you look ?? Try the sticky in this forum called Loader Mods and look at post #2.

[Professor]

Anyone have a mod for mill's "all in one" H card unlooper. Please post pics or discuss if you do. Thanks!!!

[mikeee]

Anyone know what this loader is its from the hu days came in white case nothing on it. Is it moddable? and if so how. Thanks Mikeee.

Hope you don't mind Mikee, edited the pics to a better jpeg size so the thread wasn't all stretched out.

[Cimba]

Detonator II mod trying it now.
C&P
Here's a pics of the orginal mod. After trace'ing out the detonatorII a bit I found that 74HC00 (3b) is being fed from the block via the 3rd-74HC0053 Pin-15 located at U11 on my board. So I decided to connect the 74HC00-2b to U11 pin-15 instead of connecting to Pin-2 of the 74hc04. I found that this minor mod seemed to improve my glitch rate success, all credit goes to the orginal creator of the mod.
Good Luck satvia

Thanx for the work lightning, I have had some pm's about the pic of the working mod. The #'s in the pic don't seem to correspond to the #'s in the worded instructions; ie: hct00 and 74ch00 ( I assume they are the same). Here is a sample question: " I have been tryin to mod my det 2 for two months just one ? do you know if i only lift the pins on hct00 only.i was not sure if i have to lift the pin on hct74 and hct04
thanks a lot "

[lightning0009]

I just lifted the pins on the the hct00 only when I modded mine the other day. I could only get ------------------ when trying to unlock a rom102 with it. Satvia who posted the mod at another site suggested connecting to the U11 pin15 instead of the pin 2 of the 74hco4 and that's what I did, but still no luck with it yet. I poured a bunch of glue gun glue on mine, so I can't really go back and mess with it dammit, but maybe. I bit the bullet and ordered a nexus, but I'll keep glitchin here with my kickass clone. I have been able to unlock one 102 with it so far.

[tyfon]

Cimba,
I have posted a question can you look at it..
is about the Mikobu 111 with the MOD.
and other question..
can you help.
Here is the link.....

http://www.dssftp.com/forum/showthread.php?t=44611

thank you in advance.

tyfon

[mikeee]

cimba would you know what kind of loader I have the pics are a few posts back?

[mike123333]

The attached is the Mod on a Scorpion version 1.3
The wiring is as follows: Refer to Pic's

Chip 74HC00AP - lift pins 1,5,11, 12, and 13
Chip SN74HC74N - lift pin 5

All other pins noted for attachment remain socketed and not lifted.


A. Chip 74HC00AP

Pin 1 is attached to Pin 5 of the SN74HC74N

Pin 5 is attached to Pin 18 of the Atmel

Pin 11 is attached to Pin 10 of the 74HC4053N

Pin 12 is attached to the bottom of the 4 switch clock selector. Make sure you use the correct side of the switch. This would be where all the connectors are tied together.

Pin 13 is attached to Pin 14 of the Atmel.

The pot I used is a 1K, 10K, and resistors. I select either one of these three variances by jumpers on the board. One end of the pot goes to the gnd and the other end to the card VCC. Use the first 2 legs of the pots. These are labeled on top of the pot as 1,2,3. I purchased the Pot's at Radio Shack.

I do not lift Pin 18 of the Atmel that is going to the Max 232 chip Pin 10. Leave them as is.

The switch is set on position 2 for Rom 3 and Rom 10. Position 3 for Rom 102. The position 3 gives me the best responses from the Cam for 102. I am still trying to get into the ROM 102.

I used the krypto Tucker schematics for this Mod.

I hope this helps anyone in need of the wiring for the Scorpion.

Any questions, please don't hestitate to give me a holler!

Mike




Mike12333

[mike123333]

After posting this mod, I installed the 25 Ohm Rheostat in place of the pot and fine tuned it to a 21.3 ohm setting. Instantly I unlocked 3rom 102's in 45 minutes. I used switch 2 and also lifted Pin 10 of the Max232.

This concludes the Mod of the Scorpion version 1.3.

Mike


The attached is the Mod on a Scorpion version 1.3
The wiring is as follows: Refer to Pic's
Chip 74HC00AP - lift pins 1,5,11, 12, and 13
Chip SN74HC74N - lift pin 5
All other pins noted for attachment remain socketed and not lifted.
A. Chip 74HC00AP
Pin 1 is attached to Pin 5 of the SN74HC74N
Pin 5 is attached to Pin 18 of the Atmel
Pin 11 is attached to Pin 10 of the 74HC4053N
Pin 12 is attached to the bottom of the 4 switch clock selector. Make sure you use the correct side of the switch. This would be where all the connectors are tied together.
Pin 13 is attached to Pin 14 of the Atmel.
The pot I used is a 1K, 10K, and resistors. I select either one of these three variances by jumpers on the board. One end of the pot goes to the gnd and the other end to the card VCC. Use the first 2 legs of the pots. These are labeled on top of the pot as 1,2,3. I purchased the Pot's at Radio Shack.
I do not lift Pin 18 of the Atmel that is going to the Max 232 chip Pin 10. Leave them as is.
The switch is set on position 2 for Rom 3 and Rom 10. Position 3 for Rom 102. The position 3 gives me the best responses from the Cam for 102. I am still trying to get into the ROM 102.
I used the krypto Tucker schematics for this Mod.
I hope this helps anyone in need of the wiring for the Scorpion.
Any questions, please don't hestitate to give me a holler!
Mike
Mike12333

[larryking123]

I have this board been trying for like all summer
can't get anything, just 6F all day long
I stripped a power supply , and use the trimmer pots
using VCC I was able to get -'s but when it went to read all I got from the card was FFFF as response.

so the scripted died.
I had the trim pot down to like 20ohms, I got that 25 ohm rheostat and get all FFFF not , I think it is too low, cause I can't get to 6f and more, just RESET and FFFFFF.
I am using NewD8 D9 D11, no dice, adjust VCC and delay no luck , never changes from 6FF6F6F or FFFFFF's

I used a copy from CC o modd but I am not sure if it is right
I just would like to confirm that my modd is right
here is a picture of the board, they were mostly sold in Canada

the second picture I used to make my modd

[Rico69]

I have a Atomic PUT Loader, black case. Any Mod for it?

Thanks
Rico69

[JT]

I have a Atomic PUT Loader, black case. Any Mod for it?

Thanks
Rico69

I have one of those too. Never have found a mod how-to for it though. It was great in it's day and should be able to be modded, but couldn't figure out how to do it myself. I actually use it as a chip programmer for my emu chips now days since it has the socketed atmel. If you run across a mod how-to could you please post it in this thread.

[#40Fan]

Here's pics of a modded AIO. Use these directions to go with the pics. I did it without lifting any pins though. Thanks to everyone else that has posted info on this.
If anyone has any info on dip positions that work better for certain cards, please post them.
Instructions for wire connections.
IC7 pin 1 to IC2 pin 7
IC7 pin 2 to IC3 pin 9
IC7 pin 3 to IC7 pin 4
IC7 pin 5 to outside connection on switch
IC7 pin 6 to IC5 pin 9
IC7 pin 11 to IC5 pin 10
IC7 pin 12 to IC3 pin 3
IC7 pin 13 to IC2 pin 14
IC2 pin 18 to center connection of switch
IC4 pin 10 to last outside connection of switch
IC6 pin 8 to center pin of pot
IC6 pin 14 to either outside connector of pot.
That's it for connections. To flash the Atmel
you need to set dip switch (SW1) Switch 4 to on.
Then the added switch to the side that connects
IC2 pin 18 to IC4 pin 10.
After flashing move both switches back to normal
settings. SW1 switch 4 to off. Added switch to side
that connects IC2 pin 18 to IC7 pin 5.


For some reason I couldn't edit the picture of the back side. If you count down from the top left where the Atmel Chip points are, you want to cut the trace between the 7th and 8th pads.

[lord_galathon]

OK well everyone else is asking, and who am I not to?

If anyone has the mod for the B-52 card bomber please post it or PM it to me.

I'm attaching some photos of it. It was never modded and to be honest, I don't remember how to flash it but I'm sure I have some docs somewhere.

It's always been a good HU loader/unlooper. I hope I can revive it, it cost me like 250$ way back when...

Thanks in advance.

[kornbread]

These are the pics for one of the blueboard T911 mods which often is the same as the greenboard mod.

http://www.dssftp.com/forum/showthread.php?t=52830

Would you have anything on the blackboard T-911 ?

[PonyCar]

The attached is the Mod on a Scorpion version 1.3
The wiring is as follows: Refer to Pic's

Chip 74HC00AP - lift pins 1,5,11, 12, and 13
Chip SN74HC74N - lift pin 5

All other pins noted for attachment remain socketed and not lifted.


A. Chip 74HC00AP

Pin 1 is attached to Pin 5 of the SN74HC74N

Pin 5 is attached to Pin 18 of the Atmel

Pin 11 is attached to Pin 10 of the 74HC4053N

Pin 12 is attached to the bottom of the 4 switch clock selector. Make sure you use the correct side of the switch. This would be where all the connectors are tied together.

Pin 13 is attached to Pin 14 of the Atmel.

The pot I used is a 1K, 10K, and resistors. I select either one of these three variances by jumpers on the board. One end of the pot goes to the gnd and the other end to the card VCC. Use the first 2 legs of the pots. These are labeled on top of the pot as 1,2,3. I purchased the Pot's at Radio Shack.

I do not lift Pin 18 of the Atmel that is going to the Max 232 chip Pin 10. Leave them as is.

The switch is set on position 2 for Rom 3 and Rom 10. Position 3 for Rom 102. The position 3 gives me the best responses from the Cam for 102. I am still trying to get into the ROM 102.

I used the krypto Tucker schematics for this Mod.

I hope this helps anyone in need of the wiring for the Scorpion.

Any questions, please don't hestitate to give me a holler!

Mike




Mike12333



Do you know if this mod works with the scorpion rev 2.1 version.THANKS

[PonyCar]

Does mod work for scorpion rev 2.1 version also

The attached is the Mod on a Scorpion version 1.3
The wiring is as follows: Refer to Pic's

Chip 74HC00AP - lift pins 1,5,11, 12, and 13
Chip SN74HC74N - lift pin 5

All other pins noted for attachment remain socketed and not lifted.


A. Chip 74HC00AP

Pin 1 is attached to Pin 5 of the SN74HC74N

Pin 5 is attached to Pin 18 of the Atmel

Pin 11 is attached to Pin 10 of the 74HC4053N

Pin 12 is attached to the bottom of the 4 switch clock selector. Make sure you use the correct side of the switch. This would be where all the connectors are tied together.

Pin 13 is attached to Pin 14 of the Atmel.

The pot I used is a 1K, 10K, and resistors. I select either one of these three variances by jumpers on the board. One end of the pot goes to the gnd and the other end to the card VCC. Use the first 2 legs of the pots. These are labeled on top of the pot as 1,2,3. I purchased the Pot's at Radio Shack.

I do not lift Pin 18 of the Atmel that is going to the Max 232 chip Pin 10. Leave them as is.

The switch is set on position 2 for Rom 3 and Rom 10. Position 3 for Rom 102. The position 3 gives me the best responses from the Cam for 102. I am still trying to get into the ROM 102.

I used the krypto Tucker schematics for this Mod.

I hope this helps anyone in need of the wiring for the Scorpion.

Any questions, please don't hestitate to give me a holler!

Mike




Mike12333

Does mod work for scorpion rev 2.1 version also

[vans]

Haven't been able to check it out yet. Busy busy ya know.

It does seen that nobody has even tried the SCRT.

Glad I got mine virtually free.

Lefty. I also have SCRT board let me know if you find out anything.

[mike123333]

This was the information I used to Mod my Scorpion. read it several times and use your ohm meter to trace the connections before attempting to Mod.

For ROM 102 you will need the appropriate Pot whether it be rheostat or trimmer.


This is a How to for modding any hu-loader or h-unlooper
to turn it into a nagra card unlocker.

Tools Needed
BRAIN ---- :)
PENCIL
PAPER
Exacto Knife
Solder with Iron
A little luck
A Multi-meter is a must.

You will also need to know how to find Ground and Vcc lines for your board.
This usually very easy. Pin10 on atmel will be ground pin 20 will be vcc

The first thing that must be done is to trace out some of the important connections and how they relate to the chips on your board.

1- Test Connection between max232-pin10 and atmel-pin18
<this needs to be cut> if connected you can also install
a switch on/off as this is needed for flashing the atmel chip.


2- Now we need to know what 74hc4053 we need to work with you should
have 2 of these chips. The one we want will be the one that has 74hc4053-pin4
connected directly to ISO-Slot-Vcc when you find it mark this as 74hc4053-A and the other as 74hc4053-B then you need to add a 5k trimmer pot from 74hc4053-A-pin4 to ground.
Or you can use a 2.2k resistor. If using a trimmer pot you only need the first and
second leg.

3- If you only have one 74hc74 ignore this We need to find out what 74hc74 we will
be working with if you have 2. The one we need will have a connection between
pin2 and pin6 and also betwen pin12 and pin8 mark this one 74hc74-A the other one
B the second one will not have both sets connected hopefully.

4- Now we need to find out where the clock select (Jumper Block) connects to the
74hc00 if you have a jumper setup remove all jumpers now find the row of pins
that are all connected together now test for a connection from there to the
74hc00 test on these pins (1,2,4,5,9,10,12,13) mark it down now you need to refer
to the chips pic included. Now a example if you found pin1-1a connected then you will
find that pin2-1B goes to atmel-pin7 or if you found pin2-1b connected to the 74hc00 then
you will find pin1-1a goes to atmel-pin7. In either case your next test point would be from pin3-1y pin3-1y will be connected to a AorB pin on the pic find out what pin this is. eg. I have pin3-1y connected to pin4-2a pin4-2b then will be connected to either pin5 or
pin9 of the 74hc74 you will have 2 of these chips on a huloader.


5- After you figure out the above mess :) you need to cut the trace from the jumper block
and the 74hc00 and you need to cut the trace between the 74hc74-A and the 74hc00 then
you need wire jump from either 74hc74-A pin5 or 74hc74-A pin9 which ever one was
connected directly to the 74hc00 in the first place. To the pin on the 74hc00 that was
connected to the jumper block then you jump the pin from the 74hc00 that was connected
to 74hc74-A pin5 or 74hc74-A pin9 which ever one was connected directly to the 74hc00
to the atmel-pin18

6- Almost there now we need to jump the jumperblock to a unused gate on the 74hc00 unused
gates would be usually tied to vcc or ground so those traces need to be cut. The input
gates are the A-B on the chip pics and Y is out So if you connect the jumper block to
pin13-4B then you need to connect pin12-4A to atmel pin14 and pin11-4Y to atmel pin6

7- And you should be done.

I have a pic of a generic huloader with the orginal traces included to give a good Idea
of what is done.

Original traces in dark blue
new jumps in pink
yellow cut traces

Also look at the chip pics if you can understand them and how the gates work then you can sorta ignore exact pin #'s and use the gates as they are A1-B1-Y1 ect

Also tested on ROM10 with NEWD8.HEX

Also check connections for other shorts on all pin locations you are working with if you
can follow the traces to see if they are connecting to anything different.

Also test after you cut a trace test to make sure there is no more connection.

Enjoy and have fun.


I hope this helps the folks out there with the different loader and unloopers.


Mike

[B00gieman]

Hello.
What about the mod for the duolabs unlooper? Anyone got it working with nagra cards?
Thanks in advance.

[2getwired]

i found a terminator t5 today but do not see any mods, can anyone help?
info on a ULPro would be cool too.
has anyone done a mod soley on the fact that the ic's were the same as some other mod? just a different layout and board color??

[Nefarious]

heres a thread on the t5

http://www.dssftp.com/forum/t41631-moded-my-terminator-typhoon-works.html

[zit]

102 and Vector Tech Mod
Could someone take a look at this and give me sugguetions. Its an Vector Technologies Unlooper that I modded to get into the nag 1 cams. It did the job with no problems but for some reason I can't seem to pop any nag2 cards. I recieve the correct response (+-+---+--+-+ and so on) but after have gone by still nothing. This is how I have it setup

On the 74HC00, Lift pins 4,9,11,12,13
pin 4 will not used but it still lifted

On the HC74 lift pin 9
On the Atmel, lifted pins 14 and 18

On the 74HC00
Pin 5 to Pin 18 of atmel
Pin 9 to Pin 9 of 74
Pin 11 to Pin 11 of U8
Pin 12 to where pin 9 would be connected bottom side
Pin 13 to Pin 14 of atmel

Center leg of pot is connected to pin 4 of U8 under the board
Outside leg of pot is connected to pin 7 on top of the leg of U8
Resistance is 2.2K ohms measured accross the two conected legs.

Any help would be greatly appreciated
Thanks in advance.....

[bearpaw]

i have a red dragon hu programmer can i modify it to unlock rom102 cards.

[mike123333]

I had this kind of response with my Scorpion Mod. almost 2 weeks playing with it. Then I changed out the potentiometer with a a 25 OHM Rheostat. Fine tuned it 21.3 ohms, it could be different for your loader, and bingo the 102's popped like crazy.

It appears that the potentiometers have a low amperage draw. The rheostat varies the amperage to get higher voltage.

I even went to the extent of testing a series/parallel resistors to achieve a 21.3 resistance 9low amperage). hours later never popped. Once I hooked up the rheostat again had success.

Read the gltiching thread, lots of help there. This was not my work, so I take no credit for it.

Good Luck.


Mike



102 and Vector Tech Mod
Could someone take a look at this and give me sugguetions. Its an Vector Technologies Unlooper that I modded to get into the nag 1 cams. It did the job with no problems but for some reason I can't seem to pop any nag2 cards. I recieve the correct response (+-+---+--+-+ and so on) but after have gone by still nothing. This is how I have it setup

On the 74HC00, Lift pins 4,9,11,12,13
pin 4 will not used but it still lifted

On the HC74 lift pin 9
On the Atmel, lifted pins 14 and 18

On the 74HC00
Pin 5 to Pin 18 of atmel
Pin 9 to Pin 9 of 74
Pin 11 to Pin 11 of U8
Pin 12 to where pin 9 would be connected bottom side
Pin 13 to Pin 14 of atmel

Center leg of pot is connected to pin 4 of U8 under the board
Outside leg of pot is connected to pin 7 on top of the leg of U8
Resistance is 2.2K ohms measured accross the two conected legs.

Any help would be greatly appreciated
Thanks in advance.....

[kiutie]

Anyone can post some clear pictures of a Sureshot, please?
All what you get for this unlooper is just crap, unclear and low definition, impossible to follow.
Pleaseeee...!

[lord_galathon]

This is a green board with a 4-position red DIP switch. Any info re Mod with picture would e appreciated. Tnx in advance.

:D

The actual name for it is a B-52 Card Bomber. I have one. Going to work on it now. Will post photos and results.

[B00gieman]

Problem; Problem; Problem

Take a look at http://www.duolabs.com/trunker.htm and you will see a explanation off this device.

At the top Duolabs crew say:
"- Wildthing/Kpyro based unlooper with AT90S2313-10P DIP format. All features are enabled."

and...

"The Unlooper Trunker basically designed on WildThing/Kpyro Schematic with the addition of a CPLD Xilinx XC9536XL-PC44 and an external clock generator. All together is knows as modified Kpyro Unlooper"

... they also provide a link to the ORIGINAL SCHEMATIC FROM WILDTHING UNLOOPER. (http://www.cellularcenter.it/duolabs/unlooper.zip)
... so when you buy it you think that the only difference is the addition of a xilinx.... its not true.

A already tried to mod it using the nagra mod for wildthing... if the schematic is the same the mod should work... but it doesn't!!!
Please anybody?

PS: in the image below... the mod image.... the blue lines is the new circuit to make... red dots means that the pin of the IC should be pulled up.

[mexebrasil]

Hi everyone. I am new and have DishNEt. The whole thing is down now so I am assuming I need new keys. Can someone please help me out in terms of where I might find them? Much thanks in advance.

[Nefarious]

Mine works great, heres the thread with my info on it.

http://www.dssftp.com/forum/showthread.php?p=332163#post332163

[thedudd]

I also have this same type of unlooper, I have looked everywhere, if you finf a mod please pm me. Thks in advance

[Del Valle]

Hello guys does anyone has or knows how to mod the X loader unlooper made by Terrence & Phillip mfg. canadian made and can it be used for n2 cards ? your help is really appreciated,thank you in advance.

[psad]

Detonator II mod trying it now.
C&P
Here's a pics of the orginal mod. After trace'ing out the detonatorII a bit I found that 74HC00 (3b) is being fed from the block via the 3rd-74HC0053 Pin-15 located at U11 on my board. So I decided to connect the 74HC00-2b to U11 pin-15 instead of connecting to Pin-2 of the 74hc04. I found that this minor mod seemed to improve my glitch rate success, all credit goes to the orginal creator of the mod.
Good Luck satvia

Lightning0009:
Just a comment on the resistor mod on the back of the Detonator II board. After tracing this out and viewing your pic it appears that the resistor goes from the Card VCC to pin 16 of the Atmel chip. If you measure pin 16 of the Atmel with no card installed it is grounded (where I beleive the resistor should be tied). With the card inserted this is only connected to pin 16 with no path to ground. My setup was very unstable with this resistor installed the way your pic shows it. In fact I was unable to get any change in VCC measurements. I have since tied the resistor from VCC straight to board ground and things are working better now. Have others determined this as well?

PSAD

[kiutie]

Man, nobody know how to modd a sureshot Xtreme unlooper? Please post some nice pictures.
Thank's

[Bunker]

Cimba or anyone,
I've been reading everywhere looking for an hu unlooper/loader like mine...no logo on it...got in Canada from Huworks. Never used the black toggle between 9v and 9 pin conx...not sure what it's for... Before I attempt any mod ...does anyone have any info on it ?
Appreciate any advice.
Bunker

[lord_galathon]

A friend temporarily donated this HU loader to help me with my 2000T. It's very similat to a T911 BUT:

It only has ONE 74h4053. First time I see THAT.

Notice on the upper left, you can see U6 is a 74h4053 but U7 is marked BUT EMPTY!!! It does work with HU cards BTW. I tested it, it will even unloop them.

Can anyone look at the photo and help identify it?

Conversely,

I'm still working on that 2000T but it's difficult. I can't get an ATR from it and when running any unlock scripts I get 6F6F or ++ all the time, if I move the rehostat too low I will get RESETS or XXs. Admittedly, I'm running out of holiday time to play with it.

Thanks in advance.

[Cimba]

Unknown 2 me, looks like another T family clone but I'm guessing. Try comparing to other posted pics.

[lord_galathon]

I found these pics on another site. It's a Nexus T911 apparently.


I also found a zipped PDF file. NO CREDIT TO ME.

I'm posting it here for info and to help others that might be looking for the same loader mods.

I started modding it, succesfully lifted paws 4-5-6 off the 74h00.

Breaking for lunch, will continue after if my daughter lets me...

I will post my own photos of the modded unit once I'm done.

Quick question, is there a way to test a rehostat to make sure it's a rehostat and not JUST a plain old POT? Thx.

[ah33919]

I have this loader and I'm trying to get some instructions on how to modify it. Thanks in advance.

[B00gieman]

@eh33919
Hello.

Where did you find that picture? the unlooper is already moded... i've also seen this one in here. Try to search.

Need help on DUOLABS UNLOOPER.

[ah33919]

I found that picture on the first page of this thread (posted by larryking123) maybe I'm losing my mind but I can't find any info on the mod and , yes, I sent him a PM. If anyone else has any info, it would be greatly appreciated.

[ah33919]

Found it at CC...thanks

[jimyt]

Lot's of good info in here

I modded a T911 I was given last week and now I have 6 Rom 10's that are now open , and all of them have been tested and work great! Before I had 1 open Rom 10. And a bunch of ice scrapers. Not a bad reward for about an hour of work. And I know I still have a couple more around here I have to dig out, I came close to throwing all that out when they went to N2, never have seen them raised from the dead before. That is wild to see old blue in there workin.... I have an EMU going as well, but I just enjoy playing with the cards. It sure is nice to see this going again.

This particular one is pretty easy to mod, and there's tons of them out there on the used market, this one was going to be thrown away!! The only one mildly hard part and that's cutting the traces and soldering those same three connections on U2, just use a thin tip and get the proper knife for cutting those traces, be fast with the iron and lay off the coffee before starting, you'll be fine :-)

It works really slick and you can jump from flash to flash in seconds and keep on trucking, just switch 1 on and turn on the installed switch to flash and use 2 and 5 and open the switch to glitch, I have not seen any luck from playing with those other switches, but I sure have seen results with playing with that 5K pot, you are wasting your time if you try a fixed 2.2K ohm in there on U7, all of mine started glitching good at just under 1/4 of the pots resistance, say 1K ohms or thereabouts but all were slightly different, a pot is a must, it is not a "set and forget" deal. If you don't have a pot handy and are in a hurry you could try a fixed one, but I would try many values and I would start at 1k.

I have 6 left that show good atr in Niagra, both A23's and A24's that for some reason I cannot get them to try and glitch, in fact the 911 says no ATR at all, and all the srcipts and the A23 Unlocker just reset over and over, On those are you supposed to let it run long term as in hours and overnight or are you wasting your time? The ones I opened showed glitching fairly quickly, some took several minutes to open once they started glitching, others opened in a few seconds, but these might have done a couple of resets at most when I started it up, and then they went to work glitching, but these last ones only reset over and over and say there is no atr. Any idea what I am doing wrong? I have let them run as long as 1/2 hour.... I don't understand why no atr and in Winexplorer in the ISO mode it as well shows a normal ATR just like in Niagra, anyone ever seen cards act like that?

Also as far as what I used, I had my best luck with the A23 Unlocker Ver1.1 program, it opened both 23's and 24's, but it said the flash was unknown but it would proceed anyway, I used newd11, but I cannot find what flash that particular app wants, it worked so well with an unknown flash I sure would love to find the one it prefers. All opened on Fixed Glitch and Hi/Lo VCC, only checked those two and it really is a performer. I opened every one I had with that one, I have yet to open one in Winexplorer using all those scripts out there (I did edit my ini file for the modded T911). But I still try. The last 2 I opened had done the reset deal for a few days, and then out of the blue they started responding and opened, but it's been quite a few days of nothing but resets on these last 6 cards I am beginning to think about last rites. But I still keep on trying.

Good luck to all and if you have something like this T911 laying around, get out the glasses and soldering iron and get to work!! You won't regret it.

Jimyt

[blocker2]

Anybody have info on modding a TCS Dynamite. It has 2 74hc4053 and only 4 dip switches. No trim pot.

[AboveUpNorth]

Originally purchased as "little red unlooper" I have followed your directions on the following mod. My unlooper is a slightly different revision. Can you or anybody take a look at my included pics...compair them to yours and be able to tell me how I might go about the "cut trace" on the version board?

Most noteable differences as follows:
My C9 is your C11
Mine is missing the resistor next to C11-C10-C12
Mine is missing J1 / 3-2-1 pinout
Mine missing LED 3 pinout

Regards, AUN

[Cimba]

Too technical for my skill level. I don't have personal experience with this loader.

[Cimba]

Since I don't know what make yours is I did a search here for red loader mods, got this:
http://www.dssftp.com/forum/showthread.php?t=34988&highlight=red+loader+mod ........and this which I think you saw:

http://www.dssftp.com/forum/showthread.php?t=52914&highlight=red+loader+mod

Try this searching but mix your words around. Good luck.

[Cimba]

I have this loader and I'm trying to get some instructions on how to modify it. Thanks in advance.

Looks like it has been modded already, more shots ?

[AboveUpNorth]

Yes I started the mod but wanted to wait with the cut trace part untill I had more information. I also have to add the switch for flashing and the potentiometer.
I have read responses on this mod that give great hope to it actually working.
I modded a mili AIO and it took flash, but only gets "reset" over and over while running :-( I'm gonna try a 10k 1 turn pot then work down to a 5k 15 turn and lastly a 1k-15 turn before I give up on it.

I have searched endlessy for this red mod, and the one posted by you looked as close as it can get. I'm currently following traces with the "mod any loader" instructions for the location of cut traces.
Many thanks for your input :-)

regards, AUN

[Texas Trophy]

Yes I started the mod but wanted to wait with the cut trace part untill I had more information. I also have to add the switch for flashing and the potentiometer.
I have read responses on this mod that give great hope to it actually working.
I modded a mili AIO and it took flash, but only gets "reset" over and over while running :-( I'm gonna try a 10k 1 turn pot then work down to a 5k 15 turn and lastly a 1k-15 turn before I give up on it.

I have searched endlessy for this red mod, and the one posted by you looked as close as it can get. I'm currently following traces with the "mod any loader" instructions for the location of cut traces.
Many thanks for your input :-)

regards, AUN

Whatever happened with this mod? This is a Wildthing and I have one but can't find any info.

[mickeyd]

Can anyone tell me about an "XL Extreme?"

I know itcan be flashed as it has a switch to allow it.

can it be used to open a 102?

thanks

[Pyotr]

Can anyone tell me about an "XL Extreme?"
I know itcan be flashed as it has a switch to allow it.
can it be used to open a 102?
thanks

Most loaders that had been used for HU in the past can be modded. The basic criteria is a programmable Atmel chip and dip switches. Dips aren't always needed but it's easier.
Mostly the weird names don't mean anything.Old HU loaders had 2 or 3 basic designs.What you need to do is look through a list of mods for the one closest to yours.Not sure if there isa list of modded loaders here,but there alot of them over at rom10x.com/forums. You need to register to get acces to the site. Hope your solder muscle is up to the job.

Just found this. http://www.dssftp.com/forum/t55819-collection-of-loader-mods.html

[Bandit5906]

You got that right: the solder is a little more testy than say maybe the hedder to the JTAG pads!

[Carl2615]

Here is an oldie. I have a Atomic PUT clear case that I would like to mod. I compared it to a bunch that have been posted but none are exactly as mine. I will try to post the pic. for it.
Any help will be greatly appreciated.

Regards.....Carl2615

[alanis]

I have this loader and I'm trying to get some instructions on how to modify it. Thanks in advance.

Where did you find info on this glitcher the one that larryking123 posted?
the one you said you found it at CC...

Any info will be apreciated
Thanks
Alanis

[alanis]

I have this loader and I'm trying to get some instructions on how to modify it. Thanks in advance.

Hi, where did you said you found info on this glitcher? the one that use larryking123 talked about?


Any info will be apreciated
thanks