Nexus modded T911

[Toolmanbmw]

Hello all I am having alot of people with my rom10 at A81
When I run VCC V2 all I get is this
VCC 2C: ??????????????????----??????????????????????????????????????--????????????--????????????????--?????? 6F = 0% FF = 10%
VCC 2B: ------????--????--????????--????------????--????--??????????????------??----??????--??????????----?? 6F = 0% FF = 38%
VCC 2A: --????????------??????--??????????------??--????--??----??----????--????????????--????--??--??????-- 6F = 0% FF = 38%
VCC 29: --
no matter what Dip switch I do... all I get is - I can never see any + ... is my card screwed ? This is a new loader from modchip... Can anyone please help...
Oh yeah and When I run either Powersync or Rom10 A81 open I get result like 69696969FF69FF6969FFFF not the usual 6F FF that people is suppose to get...

[Bandit5906]

What do the folks at Modchuckit say about it? Just wondering, or don't they offer to support their products?

[Toolmanbmw]

Humm not sure... was going to find out from u guys before I go bug them... can anyone help ?

[lonewolf2k]

i have the same one and it only need one dip . use i think it was number 3 . and flash newd8 or 9 and with this your on the right track 69696969FF69FF6969FFFF use Rom10-A81 OPEN2 and it will take some time .
and set pod to 2.2

[Toolmanbmw]

Yeah dip 3... I am going to let it run all night and see how it goes... so 69 and FF is actually working ?

[PRN]

Any updates on this matter, guys? I also bought one of these from them and I have the same result. Were you able to get them to work? Thanks!

[Toolmanbmw]

Hey... here is an update... I am able to unlock 2 102 and each one only took 5 min... so it worked good for that... and for the 69FF with my rom10... I left it going 24 hours... no go... I might try again on it in a few days.

[Jani]

Hi Toolmanbmw,

What was your setting on the switches, I have 2 and 5 on, 1,3,4 and 6 off. I was getting -------- , then 2 or 3 minutes later NoResp----NoResp,
5 minutes passed, NoResp,NoResp,NoResp then No ATR return,No ATR return.
It looped the card. BTW the card was Dish Rom 102.Any help on the setting of the switches and some inputes from people on their experince would be appreciated. Thankyou.

Jani...........

MERRY CHRISTMAS, to ALL.

[bumpysultan]

I have a 4619 Nexus that unlocked 24 rom 102 and looped 6 cards so far, if anyone having their cards looped please post what modded loader they used.

[Jani]

Hi Bumpysultan,

My'n is a 4619 Nexus, sorry to say but it looped my card, was a Dish 102.

[PRN]

Hey guys, I was able to get a ROM 10 A23 dealerlocked card open with the "A24-StreamORchecksumlocked fast" script. I used the D11 flash, put the switches on at 2 and 5, ran the VCC analyzer v2 to get the ceiling VCC, put that into the unlocking script, adjusted the pot slowly to try to get a nice flow of 69 FF and BOOM, it found the bug. Before that I could hardly get any response with the 2 and 5 on with other scripts but this once seemed to work well for our loaders.

[Toolmanbmw]

For the 102 I unlocked... I just used dip 1 on
DelayStart = &h310
DelayLimit = &h3AF
GlitchMax = 9
GlitchMin = 6
trys = 80
mix = 0.2
And I had to keep playing with pod.... my nexus only would do -------------------- than keep laying with it set it as low as u can until u see NoResp than u will see some + in there also... it like setting the pod so it is on the edge of ressting the card.

[PRN]

Ok I need an opinion. I have set my Nexus modded T911 at a pot level where a good VCC where I get some +---+---+ is around 05 but it keeps going lower and it autoresets to the given values. The other values do not produce any result, as it maintains ----- . The script says the user should not change the VCC values because it auto VCCs itself. Any opinions on the matter?

[PRN]

OK I was able to open two with switch 1 ON. So in conclusion, for the Nexus Modded T911 Orange Case, 2 & 5 ON for ROM 10s, 1 ON for 102...