Close but not yet there..Questions

[salth2oj]

I'm alot closer then I was last night, but I'm still not there. What I'm getting is the preview channels and the full guide, but all the other channels are black. I'm using the CEMU 10.exe program, that show some kind of commication, but I do get the "unknown output (& input) command" every few lines.
Now the questions

I flashed my 2 chip EMU board with 2chip-ROM101-Rev007.hex. The system screen shows DNASP101Rev007, is this correct?
The Receiver ID shows R0023245698, is that correct?
The card ID show S0439731349, is that correct?

Begin that I'm getting the preview channels, is it fair to say that I did the TSOP mod correctly? I hope..

I also used a patch to update the key. So I believe that is correct.

Any pointers? Please!!!!

Thanks

[bule666]

; IDEAKey = 3D731922275DC2C997965A0CA57927F9
$D863=3D731922275DC2C997965A0CA57927F9

add that line to 3mtier file with note pad, and patch to dish.bin worked for me..good luck

[salth2oj]

Going to give that a try right now. thanks

Question, while yours is running, do you get that "unknown command " on the dos screen?

[bule666]

If you see pic ...who cares

[salth2oj]

You are correct.....still not working

[#40Fan]

Start from scratch and skip the patching for the new key. Enter it manually.

[salth2oj]

FINALLY..........12 hrs all because of a typo. I was one number off in the BK's when I modify the TSOP. Dammmmm, but it is sweet when you get it working.
Now on to doing the tiers and adding my locals.

It does seem normal to have that "unknown output/imput command" once and a while.
Thanks again for te help.

[gio111]

What Cam Id are you guys using? I am using S0000.... with red channles ?

[salth2oj]

Is that the Can id that is coming up on the info screen? As for the cam id number that I'm using, it is the standard one that is coming with the bin with in the CEMU sw.
Hope that helps

[gio111]

Actually, it's showing the same thing's as Sakths': S0439731349-61, even if my cemu.ini is all at S000... BUt I don't think that's the problem. I changed my ZIP code and am trying to input key0 and key1 in hex as mentionned in the .ini file, but not sure how. Also, how do you change the blackout F7F7 .. ? from/to Hex. Anyways, got all the guide and red channles, not too sure what's wrong. I Believe there are 2 Cemu programs going out there, thx for your inputs and suggestions.

[salth2oj]

Are you getting the preview channels ? It sounds like your 3m patch is not correct, that is most likly why you have all the "red channels" in the guide. I did find a bin file that had the correct working keys and the correct tiers. Look around and you should be able to find it, if not let me know. The cemu that is working for me is cemu-10.exe. The only thing I edited in the ini file was my BK, ird # and the dish.bin name.
Did you do the mod in the TSOP?

[gio111]

I am using DosBevCemu, not the same cemu as you I guess. It's supposed to be quite straight forward, just required TSOP mod (done) and DISH bin file key update, that's it, not sure why it is not wrking.

[salth2oj]

Are you trying to bring in Dish or Bev. I believe that they will have different TSOP. Did you use a modifiy bin or did you mod it yourself? I'm not sure if there is different CEMU program for each system (dish or bev)