New to CEMU been spending lots of time reading and playing

[hesit8]

Hey,

I've just about had enough late nights trying to figure this out for myself. Any help would be great. I'm trying to run BEV with a AVR5 8515 on a 3100. I have done the TSOP RSA update. I flashed my card with the N2-0801-IRD2PC.pfg. I am trying to run CEMU with a rom10.bin (included with the d/l) and the bell.bin (also included) I updated the keys with keyfix. I am getting my keys from KeyRipper, which seem updated often. The main trouble I have is when I run CEMU I get a lot of UNKNOWN INPUT COMMANDs. I've tried running a dos boot disk on an older celeron and also on a PIII-500. Am I missing a step somewhere. As usual I can receive the music channels and the BEV Setup Channels. I have full Sub access in the Menu, just no Audio or Video. Thanks in advance for anyones help.

Hesit8

[BiggerBear]

Did you make sure the Boxkeys are the same on the Receiver as the Boxkeys on the Floppy. One wrong diget will only get you previews. In Boxkeys for 0's you use the number key on the keyboard!

[hesit8]

Yes I do believe that all my values are correct. Any other ideas. What should I expect to see if I open Bell.bin in Nagra edit? When I run cemu it says he rom version is 10. Should this be 10 or should it be 102?

[BiggerBear]

This Is A Copy of My BEV Cemu INI File.



#
# For comments any option use the symbol #
#
# key0/key1 - 16 digit hex
#key0 6324A1E30814832A
#key1 BF7FC61F9930C3DA
#
# Windows : COM1 for COM1, COM2 for COM2...
# Dos : 1 for COM1, 2 for COM2....
# Cygwin/Linux : /dev/ttyS0 for COM1, /dev/ttyS1 for COM2 .....
#
#port stream
#
#port COM1
#port /dev/ttyS1
port 1
#address 3F8
#irq 4
#
# Baud Rate Available 9600,19200,38400,57600,115200
#baud 57600
baud 115200
#
# The name of your ROM file
#rombin rom3.bin
rombin rom10.bin
#rombin rom11.bin
#
#dishbin eeprom.bn3
dishbin dish.bin
#dishbin eeprom.bn11
#
# Tier ep3 file
#tierfile tiers.txt
#
# The name of your EEPROM file (File to upgrade with your information)
# BoxKey Hex - Must Be 16 Digits
#boxkey 87382EC5ACC1047E
#
# Cam ID Decimal - The number after S in sysinfo screen
#camid 0011851319
#
# Ird ID Decimal - The number after R in sysinfo screen
#irdid 0023245698
#
# Black out Hex - Must Be 24 Digits
#blackout 7F7F7F7F7F7F7F7F7F7F7F7F
#
# Choose the Daylight Saving
# 1 - For Daylight
# 0 - No Daylight
#daylight 1
#
# Choose a good Time Zone work with Zip Code and DayLight (ADDRESS 0xE40B)
#
# alaska
# eastern
# central
# mountain
# pacific
# atlantic
# newfounland
# virgin
# honolulu
#tz central
#
# Zip Decimal
# Chosse a good zip code for your location (Need for a good TimeZone)
#zip 53207
#
# For write to DISH.BIN NoSave 0
# No Write to Dish.BIN NoSave 1
nosave 1
#
# 1 for Debugging
# debugging 0
#
# streamlog <filename>
# if no filename is given, default is streamlog.txt
#streamlog
#
# Use this option for diplay different output information
# CMD IRD command, and other cmds logged
# CAM not used yet
# SAVE not used yet
# 6805 debug the 6805 emulator commands. This is very very
# intensive
# MAP debug the map functions from libgmp
# ROM3 debug bytes placed in ROM
# NYI not Yet Implemented feature debug
# INPUT debug incoming byte strings
# OUTPUT debug outgoing byte strings
# COMM debug low level communication
# RUN output various info taken from a running bin (keys, etc)
# KEY output just key info
# EMM debug EMM's that have been decoded
# DEBUG turn on debug debug processing :)
# NONE turn ALL debugging off
# ALL turn on ALL debugging from above
# debug RUN KEY NYI EMM INPUT OUTPUT MAP ROM 6805
#debug RUN KEY NYI EMM INPUT OUTPUT ROM
#debug RUN KEY NYI EMM ROM
#debug RUN
debug INPUT OUTPUT CAM
#
#Atr Baud Rate
#ATR Baud Rate Available 1200,2400,4800,9600
#atrbaud 9600
#AVR or mofified serial port
protocol avr
#protocol modserial

[himeros]

The main trouble I have is when I run CEMU I get a lot of UNKNOWN INPUT
COMMANDs

I get lots of bad input and output commands running Dish, but Cemu is working just fine. If along with the bad commands, you are getting other displays on the screen, the board is talking to the IRD. Like other have posted, double check the keys. If running from Dos, make sure the swap file is working, check the screen at boot up for this. Good luck

Himeros:)

[orville]

Edit line D863 and D873 manually with nagredit. Add the latest keys in your dish.bin and you should be good to go. I had the same issue and found I needed both keys in the proper spot to work. I had issues with the auto key patcher. It moved the keys to the wrong header.

[gio111]

Hesit, you have a Key problem, nothing else. I have all channels up and get input/output command errors, but all is working A1. As mentionned in the last post, make sure your keys are up to date in D863 and D873 in the dish.bin

[hesit8]

Well I've tried using the dish.bin with the keys manually entered in D863 and D873. I've tried using the bell.bin with the keys entered manually and it just won't go. I think things seem to be working because I get the menu with full sub as well as music. I just can't get the picture or sound. Am I running the correct pfg for my card?

[gio111]

I would give you a key programmer, but for some reason, I keep getting error uploading files on this site ???

[hesit8]

I am trying to run BEV so I should use the bell.bin with the new key 36 01 D5 31 EF 9F EF 33 33 D8 AE E0 39 7A 78 61 (as of post) in D863 and also in D873? my cemu.ini file is the same as the above posted, other than looking at bell.bin.

[gio111]

I'm running Bell with a Dish.bin, does'nt matter. Current keys are D863=3601D531EF9FEF3333D8AEE0397A7861 D873=DCB0E5194CA6DC75867011C9D69F16AB

Input both hesit.

[hesit8]

Yeah I figured that out late last night. Is the a different PFG I should be using. The way it is now is... If I have as you say above. I get the Porn. If I reverse the two keys around I get the rest but no porn. I've seen on different boards that there is a new PFG that allows both keys to be used. But finally I do get some video. I started from scratch. I think maybe the bew RSA was wrong in the TSOP release I uploaded to my IRD. Anyways If you have some insight on the other issue that would be great.

[Innsure]

Everything else but no porn. Any ideas. Thanks.. running charlie

[gio111]

This is the PGF you need for the Avr:

http://www.zip150.com/download.php?f=spca43a5b149bc648