Card Lock

[Bino]

I didn't know the password for my card so I used:unlockN2rom10Emu.D2C.
Everything went right until I did one step clean.

;Cardcoders ... Unlocks patch version 3D ep10
;You should see this for successfull unlock , if not try again
;RX: 3F FF 95 00 FF 91 81 71 FF 47 00 44 4E 41 53 50
; 31 30 32 20 52 65 76 31 30 33 64
;TX: 21 00 08 A0 CA 00 00 02 FF 00 06 B8
;RX: 12 00 02 6F 00 7F
; Anarky
rs
tx 210008A0CA000002FF0006B8
dl 0150
rx

RX: 3F FF 95 00 FF 91 81 71 FF 47 00 44 4E 41 53 50
31 30 32 20 52 65 76 31 30 33 64
TX: 21 00 08 A0 CA 00 00 02 FF 00 06 B8
RX: 12 00 02 69 00 79


With one step clean I get the following:

Opening of COM1 was successful
ATR String: 3F FF 95 00 FF 91 81 71 FF 47 00 44 4E 41 53 50
31 30 32 20 52 65 76 31 30 33 64
ROM Revision: 102
EEPROM Revision: Rev103
Error, unsupported card type
Closing of COM1 was successful
Error detected, One Step Clean incomplete

I need some help correcting this problem...Thanks

[ellsmako]

Your password for unlocking the card first is at location
$D0D6:AABBCCDDAABBCCDD unless you changed it ( recommended )
So try that one first.

then apply the d2c and clean

[Bino]

When I follow your instruction, I get this message:
Opening of COM1 was successful
Removing card lock
Closing of COM1 was successful
Bad password or BackDoor not present

Your password for unlocking the card first is at location
$D0D6:AABBCCDDAABBCCDD unless you changed it ( recommended )
So try that one first.

then apply the d2c and clean

[traylehr]

your most likely screwed , i was reprogramming a card & was adding extra patches for the keys/blk. screen now the card does the same. tried all i can think of ( all the 2DCs, passwords) , still closed. when the cards ( rom 10, ect,,) are password / bad programming blocked there very , very hard to reopen, sometimes a person can stumble across a program that will open there card , it requires a lot of trial & error testing.

[Bino]

I was able to open the card, I was using the wrong password. Thanks for the help.
your most likely screwed , i was reprogramming a card & was adding extra patches for the keys/blk. screen now the card does the same. tried all i can think of ( all the 2DCs, passwords) , still closed. when the cards ( rom 10, ect,,) are password / bad programming blocked there very , very hard to reopen, sometimes a person can stumble across a program that will open there card , it requires a lot of trial & error testing.

[tyson44]

for all of you havig problems with the d2c your password is 9171bd0ffe375fba

[tyson44]

for some reason my card went the same way and the password was aa bb cc dd aa bb cc dd and i never patched a thing to it i was at it for days and my password came out to be 91 71 BD 0F FE 37 5F BA use that password

[ml821]

Tyson44. You're Great. . .
I got the same problem with 2 of my rom 10 for a couple weeks but can't make it open. Use your keys and open up both of them today. Thanks a lot;) ;)