Keys won't roll on my 301.013

[midnight]

I have been working on this 301.013 single chip receiver for a month now and I still can’t get it to work. I did the 12 volt vidmod. Got to read the tsop. Change the IrdID and BK for the 102 fix. Wrote to the tsop and put the unit back on line. Receiver seams to be working ok . The software version is P209. Wrote the 06gopherx 32 tiers and v 16 blocker bin to my clean card and patch it with the ROM102-BLOCKER-V22-AND BACKDOOR PASSWORD patch.

Got the card in the receiver. The receiver does its thing and I get channel 101, 103.
I can’t get the regular channels. I get the wait message. Your card is not authorize wait or change channels. That’s ok, It just needs to roll the keys. But It wont. I have had this receiver on stream now for 8 hours and it still won’t roll the keys. I don’t know where to change the keys manually on the bin file, if I did I could try that but its still doesn’t explain why I can’t get the keys to roll. I did a 309 a month ago had had no issues. Does anyone have any ideals because I am now lost.
The vidmod uses a switch. Could it be that the wires are too long and block the keyroll. The switch is in the normal position at this time and there is continuity between the wires.
Any help would be greatly appreciated.

[dishman84]

READ MY POST IN http://dssftp.com/forum/t56619-rom-102-on-a-301-013.html

HERE IS WHAT YOU NEED :
wXX.yourfilelink.com/get.php?fid=12143 (http://www.yourfilelink.com/get.php?fid=12143) (REPLACE XX WITH WW)

DO NOT CHANGE BOX KEYS OR ANYTHING, AND BE SURE TO APPLY THE INCLUDED BLOCKER TO YOUR CARD AS WELL AS IT IS NEEDED AS WELL.

[midnight]

Got the files. Wrote the eeprom and tsop. Clean the card and wrote the bin supplyed and the blocker. Get the same thing but this time, the guide is all red.
So I change the date for the tiers and wrote it again. Now the guide is blue but the 005 nag is still present for 2 hours now. This card will not roll the keys.

[skinerd]

I would be suspicious of the receiver....you sure it's correctly modded?? SKs removed, receiver number and boxkeys relocated??

[midnight]

I would be suspicious of the receiver....you sure it's correctly modded?? SKs removed, receiver number and boxkeys relocated??


I did the 12volt mod. I was getting errors prior to mod. Now i get no errors when i use jkey. So, I would think that the mod is correct. I then use the tsop and eeprom from dishman84. I would asume that the SKs are remove and the receiver number and boxkeys are relocated. I don't realy know how to check

[skinerd]

I did the 12volt mod. I was getting errors prior to mod. Now i get no errors when i use jkey. So, I would think that the mod is correct. I then use the tsop and eeprom from dishman84. I would asume that the SKs are remove and the receiver number and boxkeys are relocated. I don't realy know how to check

If correctly applied, the flash, when read in jkeys will show as default 301-010, that would indicate you have a modded flash written.

Too many people that try to get there mods done, and fixes installed........no saben ni donde vienen, ni donde van.

[midnight]

If correctly applied, the flash, when read in jkeys will show as default 301-010, that would indicate you have a modded flash written.

Too many people that try to get there mods done, and fixes installed........no saben ni donde vienen, ni donde van.

I have three version of Jkey on my computer. One is the regular version, Version 2.9.9 Build 016. It shows my receiver as a 301.010. The other version is for built for the 508 and it shows it as a 301.010 but my last version of Jkey made for the 301.013 shows the receiver as a 301.013. I hope that this makes sense to you. This is also the version that I used to write Dishman files to my receiver.
I do know that I have also tryed to mod this tsop for the none clone 102 card but in GENDT08, it does not see the receiver properly and will not apply the SK to the image.....Tu a raison, je ne sais pas quoi faire.

[CYCO]

I have three version of Jkey on my computer. One is the regular version, Version 2.9.9 Build 016. It shows my receiver as a 301.010. The other version is for built for the 508 and it shows it as a 301.010 but my last version of Jkey made for the 301.013 shows the receiver as a 301.013. I hope that this makes sense to you. This is also the version that I used to write Dishman files to my receiver.
I do know that I have also tryed to mod this tsop for the none clone 102 card but in GENDT08, it does not see the receiver properly and will not apply the SK to the image.....Tu a raison, je ne sais pas quoi faire.
midnight I had to edit the CGF file in GENDT08 to get the apply button to work. In the file and scroll down to the 301.013 and edit the bottom part to look like this. It worked for me. But i am still having trouble getting my tiers right on my card. All channels are still red as of now. But i am getting closer than i was.
// 301.013 16AB
// 31 30 45 4E 50
[301.013]
model = 301.013
modelid = 10ENP
modelpoint = 3DFFF4
softwarepoint = 3DFFF8
checksumstart = D0000
checksumend = 3DFFFC
checksumpoint = 3DFFFC
checkpoint = 3DFF90
bootstrappoint = 3FFFA0
bootcspoint = 3FFFAC
buildconfpoint = 3FFFA8
irdnumpoint = 3FFFC0
boxkeypoint = 3FFFC4
rsa1 = 205D7C
rsa2 = 205DBC
sk = 3FFF40
dualtsop = 0

[skinerd]

Ok, I'm a tad lost......what, exactly, are we trying to do?

Why not just use GOPHERX's 42 tier 3m and hge V22 blocker, it works GREAT..get that figured, then worry about the SK versions, they are considerably tougher.

[stich]

Midnight when i used gopherx 32 tiers on 301-13 i had all red, put gopherx 42 tiers on Rom 102 getting everything. Thanks gopherx.

[tigersat]

flash and write new clean Tsop

[midnight]

Well, I finally got it.
Here is what ended up working for me.
I wrote my original tsop to the receiver. Erase sa49 and updated the software.
Save the updated tsop and opened it with FlashEdit Beta9. Used the script called
301-013 P208 catemu dt08 Enforcer. I then save that image and wrote it to the receiver.

As for the card, I use the GopherX 42 Tiers and PPV bin and applied the V22 blocker patch. Wrote to card.
It’s now up and running. Thanks to everyone that help.