Looking for TSOP for build CANJ

[abba]

want to convert one of mine dish 2800 to bell but i can't find anything close to CANJ .If someone has it ,please let me known where to find it. I already tried some of them like CSCA, COGD CASD CAJA, none of them worked.:mad:

[mopar611]

The first two letters must match.. So the first to builds you listed wont work..

3 is better and 4 is the best..

Too bad you fucked with it already.. All you had to do with that dish receiver is delete your sector and restream it to bev to make it a bev receiver..

If you cant find a bev receiver build for yours, use a dish build config.. Change all the info in flashedit to yours like usual.. After you are done completely flashing, erase your sector then restream it to bev..

You should be good to go.....

Mopar

[abba]

Thank's for fast respond I have saved Dish Tsop .I"ll try to do that.

[mopar611]

Thank's for fast respond I have saved Dish Tsop .I"ll try to do that.


I should of asked if you saved the origianal tsop.. LOL

Ya, thatll work.. Just flash the original then erase the proper sector
then hook-er-up..

Mopar

[abba]

I LOADED MY OLD tsoP AN EPPROM. Now i can't power on my ird.Found couple close with CASD ,modified to CANJ build configuration and still can't power it on.Getting frustreated running out of options

[skinerd]

I LOADED MY OLD tsoP AN EPPROM. Now i can't power on my ird.Found couple close with CASD ,modified to CANJ build configuration and still can't power it on.Getting frustreated running out of options

Incompatible flashes cannot be made compatible just by renaming them.......

ALL tsop files end with an "A". The "D" and "J" are eeprom builds anyway.
In your case a CASA an CANA tsops may not be compatible.

[abba]

So ...what you suggest?I can't find build conf.CANJ anyway.What i understand it has to match first two letters.But i don't understand how come my old TSOP worked before, and now then i tried to load back in , it doesn't work.I modified epprom from CSCD to CANJ.Mayby i have problem with epprom.Tell me what you think about that.I am kind confused now what the hell i did wrong.

[abba]

my old TSOP has This
Cheksum
bootstrap 803C1C3B
proper bootstrap 8EBC967F
APP area cs 40F44638
proper app area cs 2302C2E7

I known whey have to match but which one with what

[abba]

Finnaly got figured this out.Made it run.What i am trying to do is to convert from dish to bell.So earase sa5 five times put in the stream to restream to the latest firmware.Now to reprogram the atmega 128 to bell with satvia.Do i have to change ird and boxkeys to satvia boxkeys and ird to make it work.Can somebody to guide me what is the best way to do.Just trying to be safe not to screw up agian.

[skinerd]

Finnaly got figured this out.Made it run.What i am trying to do is to convert from dish to bell.So earase sa5 five times put in the stream to restream to the latest firmware.Now to reprogram the atmega 128 to bell with satvia.Do i have to change ird and boxkeys to satvia boxkeys and ird to make it work.Can somebody to guide me what is the best way to do.Just trying to be safe not to screw up agian.

Read and save the working flash. Open it in flash edit and change the numbers, save it and write it back.

[abba]

Read and save the working flash. Open it in flash edit and change the numbers, save it and write it back.

Did that.What about the epprom.Do i need to load new epprom.