rom 10 bad atr

[couch patato]

is there anyway to use this card? blue card with alot of logos on it. thanks

[fubr]

not if truly has bad atr.
if it had good atr then yes you can trick it into thinking it is a rom 102

[couch patato]

thanks tried to read it with nagraedit and it told me bad atr. no way to copy or edit ATR? thanks again

[mickeyd]

I get a good ATR but still can't get it to clean.
When I use the reccomended d2c file, the return is:

rx 12 00 02 69 00 79 insted of: 12 00 02 6F 00 7F

Any ideas?

[fubr]

thanks tried to read it with nagraedit and it told me bad atr. no way to copy or edit ATR? thanks againI wished it was that easy
till you get a atr your pretty much codlocked..


mickeyd
what does it report when you reset atr

rom10 rev?

[couch patato]

fubr
when i put it in my rec and do sys info it runs and tells me it is a rom 10 rev23a. nag edit when i do a atr reset tells me atr string bb a0 bb d9 32 44 11 be 90 bb d9 31 44 11 ee 90 ba d9 32 44 11 bd 90 bb d9 33 44 followed by error resetting card atr string invalid. could this be and still work? also what hardware do you recommend for plastic

[fubr]

A iso and a file called Rom-10-A23-A21-Unlocker.xvb and winex5.0 will open that one for you

there are many A23 unlockers but your going to need winexplorer to run them.
seems like there was a nagredit d2c file too that would open them but winex is better imho
I dont know about hardware I have a older iso somebody traded me
I have read good about both the main ones

[fubr]

these guys here will tell you about what hardware to get I dont know

[mickeyd]

This is what I get :

Opening of COM1 was successful
ATR String: 3F FF 95 00 FF 91 81 71 FF 47 00 44 4E 41 53 50
31 30 32 20 52 65 76 31 30 33 64
ROM Revision: 102
EEPROM Revision: Rev103
Closing of COM1 was successful

[couch patato]

thanks tried that several times just as it stated same result. dugup another old iso from another card (dave) and same result. any other ideas. i would like to try this before i mess up any 102 cards i have. i can't find any other unlockers or d2c files. i am using a ISO WAVE P/S2 model iso

[Doxx]

If you do not get an ATR, you may want to try a file called jumpatr. I have not had a card to try it on, but others say it worked for them. I would post it, but apparently I cannot post anything accept a pic or txt. Good Luck.:D

[couch patato]

thanks doxx for your response.
i must need a new ISO reader or maybe nagra edit 4.1 is not for rom10x cards. heres my point i downloaded a prpgram called extreme nagea ( the one with the ladie on it) he he and lo and behold it tells me a rom10 rev @24 when i put the card in my 6000 it must have put it up one because it was @23. so now i am trying to clear the @24 lock. i have a old clear ISOWAVE programmer guess i'll have to get one from mili. when i use nagra4.1 i still get atr string invalid but extreme nag edit says it is ok any help is app. thanks to all.

[Doxx]

thanks doxx for your response.
i must need a new ISO reader or maybe nagra edit 4.1 is not for rom10x cards. heres my point i downloaded a prpgram called extreme nagea ( the one with the ladie on it) he he and lo and behold it tells me a rom10 rev @24 when i put the card in my 6000 it must have put it up one because it was @23. so now i am trying to clear the @24 lock. i have a old clear ISOWAVE programmer guess i'll have to get one from mili. when i use nagra4.1 i still get atr string invalid but extreme nag edit says it is ok any help is app. thanks to all.

It sounds like your hardware is ok, it reads in the extreme nagra program but not in nagraedit right? There is a configuration file in nagra, maybe that was changed or corrupted? Anyway, you may want to try downloading a new copy of it and see if that helps. Make sure the com port settings are correct also. I use both com 1 and 2 (1 for ISO, 2 for Loader) and I cant tell you how many times ive been stumped only to find it was somthing simple like a comport setting. You mentioned that the card was at A23, and after it was in the IRD it went to A24. If that is the case, it is likely streamlocked and you will need to use an A24 glitching script with a modded loader to get back in. Good luck.

[couch patato]

thanks doxx
i beleive it is either ISO or bad file related. i am able to see atr in winexplore when i try to remove @24 but i have not yet been able to remove it. i am waiting on a nexus to do this rom10. do you know if i will be able to use it on rom102's or do i have to buy another loader to. thanks to all for all your help. spud

[Doxx]

As long as the ISO worked in one of your programs, the hardware is likely ok. If it is, you should have no problem using any of the 102 to rom10 images to fix your card, once you get past the streamlock. Best of luck;)

[fubr]

This is what I get :

Opening of COM1 was successful
ATR String: 3F FF 95 00 FF 91 81 71 FF 47 00 44 4E 41 53 50
31 30 32 20 52 65 76 31 30 33 64
ROM Revision: 102
EEPROM Revision: Rev103
Closing of COM1 was successful
you got rom 10 right?
if you cant remeber the password or cant get unlockerd2c to work it will you might want to see if a modded loader will open it. I dont know I have never had that problem on a rom 10.

couch_potato
your getting a response to a atr just not the right one so maybe it is voltage on power supply or a windows comm port setting

[mickeyd]

Thanks, I ordered a moded loader from Milli.

[mickeyd]

I got my modded loader and sure enough it reported it opened the ROM10 but when I went back to my ISO I still can not clean it.