Nexus 4619 Unlocker & rom10x rom102 script

[Nascarfan2446]

OK. I edited the unlocker settings to:

Com=1
Data baud=115200
Reset baud=115200
Parity =none
Receive timeout=1000
Byte delay=100
Reset delay=100
Stop bits =1
Byte convention= direct
Flush echo bytes= no check
Flush receive buffer= check
Advanced tab
Check mark in device reset (no atr)
No check mark in ignore receive timeout
DTR= low
RTS= high
Toggle line = RTS

The script attempts to run and now I get invalid ATR error. I have tried the card both ways and nothing.

I read the card with a Nexus ISO and the ATR appears to be fine...

Do I have a setting wrong or something?

[Crazy1_79]

is the card making good contact in the loader? YOu don't have it in upside down do you? With the Nexus the card goes in with logos up not contacts up. Sounds trivial but it happens. try taking a pencil erasor and gently rubbing the contacts on the card.

[anna]

ok I use blue nexus unlocker, rom 10 rev 123.

Executing Script: C:\Documents and Settings\XPUser\Desktop\A24UNLOCKER\A24UNLOCKER\A2 4-StreamORchecksumlocked fast .XVB
TX Data : A0
TX Data : A0
TX Data : A1
TX Data : 07 0E 03 10 01 03 9A 00
RX Data : 07 1B
RX Data : 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50
30 31 30 20 52 65 76 41 32
TX Data : 12 15 AB 21 00 08 A0 CA 00 00 02 12 00 06 55 0E
03 85 00
RX Data : 12 06
RX Data : 12 00 08 92 04 00
Now we will try 0C20 delay
FFFFFFFF83
*********** we hit our bug *************
1200078303
===========================================
83 was hit at 0C20 delay ----VCC WAS 21
TX Data : 0A 15 A3 21 92 00 B3 0E 03 85 00
RX Data : 0A 06
RX Data : 12 92 00 80 21
***************************
* A24 CAM should be OPEN *
* test in Nagra to see. *
* if not, try again. *
***************************
Script C:\Documents and Settings\XPUser\Desktop\A24UNLOCKER\A24UNLOCKER\A2 4-StreamORchecksumlocked fast .XVB Transmission Completed

Timeout from 2A command
The Update Status Word is at 0 (Decimal)
The Fuse Byte is at 0 (Decimal)
-----------------------------------------------------------------------------------------
Executing Script: C:\Documents and Settings\XPUser\Desktop\A24UNLOCKER\A24UNLOCKER\A2 4-StreamORchecksumlocked fast .XVB
TX Data : A0
TX Data : A0
TX Data : A1
TX Data : 07 0E 03 10 01 03 9A 00
RX Data :
Script Error on Line 85
Sc.Read: Timeout Reading Data From Card - 2 Bytes Requested, 0 Bytes Read
-----------------------------------------------------------------------------------------
Executing Script: C:\Documents and Settings\XPUser\Desktop\A24UNLOCKER\A24UNLOCKER\A2 4-StreamORchecksumlocked fast .XVB
TX Data : A0
TX Data : A0
TX Data : A1
TX Data : 07 0E 03 10 01 03 9A 00
RX Data : 07 1B
RX Data : 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50
30 31 30 20 52 65 76 41 32
TX Data : 12 15 AB 21 00 08 A0 CA 00 00 02 12 00 06 55 0E
03 85 00
RX Data : 12 06
RX Data : 12 00 08 92 04 00
Now we will try 0C20 delay
83
*********** we hit our bug *************
1240078303
===========================================
83 was hit at 0C20 delay ----VCC WAS 25
TX Data : 0A 15 A3 21 92 00 B3 0E 03 85 00
RX Data : 0A 06
RX Data : 12 40 07 B0 53
***************************
* A24 CAM should be OPEN *
* test in Nagra to see. *
* if not, try again. *
***************************
Script C:\Documents and Settings\XPUser\Desktop\A24UNLOCKER\A24UNLOCKER\A2 4-StreamORchecksumlocked fast .XVB Transmission Completed

Timeout from 2A command
The Update Status Word is at 0 (Decimal)
The Fuse Byte is at 0 (Decimal)
-----------------------------------------------------------------------------------------
Executing Script: C:\Documents and Settings\XPUser\Desktop\A24UNLOCKER\A24UNLOCKER\A2 4-StreamORchecksumlocked fast .XVB
TX Data : A0
TX Data : A0
TX Data : A1
TX Data : 07 0E 03 10 01 03 9A 00
RX Data : 07 1B
RX Data : 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50
30 31 30 20 52 65 76 41 32
TX Data : 12 15 AB 21 00 08 A0 CA 00 00 02 12 00 06 55 0E
03 85 00
RX Data : 12 06
RX Data : 12 00 08 92 04 00
Now we will try 0C20 delay
FFFFFF83
*********** we hit our bug *************
1200078303
===========================================
83 was hit at 0C20 delay ----VCC WAS 22
TX Data : 0A 15 A3 21 92 00 B3 0E 03 85 00
RX Data : 0A 06
RX Data : 12 92 00 80 21
***************************
* A24 CAM should be OPEN *
* test in Nagra to see. *
* if not, try again. *
***************************
Script C:\Documents and Settings\XPUser\Desktop\A24UNLOCKER\A24UNLOCKER\A2 4-StreamORchecksumlocked fast .XVB Transmission Completed

Timeout from 2A command
The Update Status Word is at 0 (Decimal)
The Fuse Byte is at 0 (Decimal)



But what's next step?

[Crazy1_79]

anna, what dip setting do you ahve switched on? Me and Mopar have been fighting with these damn rom 10 cards all night, which program are you using, and what flash are you using with the loader? BTW, stick it in your ISO programmer and give er a read and see if you can read it.

[anna]

MMM I have to with for my ISO ,now I go it ,try to reed, nagra master 4.1 nop, try many times,one step clean nop,:(