Rom 102 Rev 242

[ghost1412]

Any file to unlock Rom 102 rev 242 yet ?

[Crazy1_79]

sure is, I bet it is in the downlaods section, it is for rev 106, 107, and 242, 243. I popped a 106 with it in seconds. They recommend you have a loader with the 4619 chips. I ordered the blue nexus' from mili. It made quick work of several cards already.

[ghost1412]

i did get this file and I try it several time using the Nexus 4619 and it kept going on and on with no luck to open the card do I have to use a certian configuration on the Win Ex ?
I thought that my firewall block the scripts so I remove it and it still no chance what else can I do ??

[Crazy1_79]

you need newd13 for the flash, I unlocked the rev 106 with the pot set at 202 ohms, with switches 2 and 5 down, I used all other default settings in the script, you need to have the loader 2 settings in winexplorer selected, I do not remember if the script automatically sets that up for you or not. what responses are you getting in the script, let it run for a few seconds and copy and past the responses into the forum here so we can see what it looks like, this is what mine looked like.

Let the 102 Glitching continue....
AVR delay = 03
Glitch Delay = 39FA
VCC = 08

RX Data : D8 91 00 49 8D 00
NoRsp+-
RX Data : D8 00 02 6F 00 B5 --
RX Data : -
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : DE CA FE C0 FF EE
===========================================
Glitch Success!! DE CA FE C0 FF EE
Card is Unlocked!!!
VCC = 02 (~4.90196078431373E-02 vdc)
Glitch Delay = 39FA
Glitch type 07
===========================================

[ghost1412]

I already flash my Nexus with newd13 my card is Rev 242 and I am using switch 2 & 5 down the only point that I am missing is the Loader 2 that I am missing where can I find that ? I can't find that on my win ex preference
The output that i am getting is same as yours except that I don't get the result that the card is open

Let the 102 Glitching continue....
AVR delay = 03
Glitch Delay = 39F3
VCC = 20

RX Data : D8 00 02 6F 00 B5
--
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : -
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : -
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : -
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --
RX Data : D8 00 02 6F 00 B5 --

and it start again and again and again

[Crazy1_79]

it automatically adjusts for the loader 2 settings, it is in the script, what is your pot set at? you will need a ohm meter to know that, the blue nexus' are popping around 200 ohms. you can check the resistance by touching the two little silver pads labeled RTS on the back of the loader. you have to check resitance w/o the power supply plugged in. cannot check resitance with power applied, I am checking around to see if the delays or different in the script for the 242's

[Crazy1_79]

I think it is in your ohm settings, you have to have resistance right. Also maybe try just dip 4 down, some people claim succes with just dip 4

[ghost1412]

I will try to flash my nexus again can you please tell me what switch should be done to flash my unlocker ?

[Crazy1_79]

just dip 6 will make it flash. then make sure you put it back to 2 and 5 or just 4 or whatever you would like to try. What are your ohms at? do you know how to adjust your pot? Do you have a ohm meter?

[ghost1412]

I just flash it again with dip 1 & 6 down and I am glitching again with dip 2 & 5 only down - no I don't have ohm meter - To adjust the pot I thinkI should turn it clock wise all the way till the end and then very slidly the oposite way
I did unlock Rom 102 before using this nexus and it work great no idea why this time it give me hard time

[Crazy1_79]

you can try guessing with the pot like that, but I suggest you buy yourself a multimeter, they are 10 bucks for a cheap one that will work just fine. the rev 242's are much fussier to unlock than the older revs. You can pop a rev 103 or rev 105 with just about any ohm setting you want to use, I have successfully popped several 103's, a few 105's one 106 and one rom 101 rev 009 all at 202 ohms, I had to move the pot to 600 ohms to pop a rom 10 rev A23. I think your problem lies in the resistance of the pot. DO NOT ADJUST THE POT WHILE THE SCRIPT IS RUNNING, YOU MIGHT LOOP YOUR CARD!!!

[ghost1412]

Thank you for your help

What ohm should be set 2 to unlock rom 102 Rev 242 ?
Any idea where I can get the multimeter with this price you mention ?

Can you PM me your email to keep in touch ?

Thanks you for your help
Aprechaited

[Crazy1_79]

the ohms should be around 200 ohms. Radio shack sells multimeters for around 10 dollars. I do not send out my email, sorry.

[ghost1412]

thank you for your help any way
I will get one multimeter today and I will try it and post the outcome
hope it will work

[ghost1412]

By the way I do have another Rom 102 Rev 240 should I use the new script to unlock it ? or the same file as the one for 242 ? I think my unlocker should be flashed same as Flash file ND13 am I correct ?

[ghost1412]

when I try to unlock Rev 240 should I use the same setting for Win Ex Loader 2 ? my concern that when I trying to read or analyse card I get this message


Timeout from 58 command

Trying to reset card...
Reset Failed!

[ghost1412]

this is the message that I get when I try to unlock my Rom 102 Rev 240 and still my card is locekd

Let the 102 Glitching continue....
LETS TRY NEW DELAY
Glitch Delay = 0325
VCC = 10

--+---+------+-NoRsp+--+---+---+-NoRsp+--NoRsp+---+---+---+---+-- hit VCCLimit, back up to &h2f vcc -------NoRsp+------------
TX Data : A1
===========================================
Glitch Success!! A0FF-INTERCEPT IS ON
BootLoader 6F 00 RSP Received!!
VCC = 26 (~0.75 vdc)
Glitch Delay = 0325
Glitch type 08
===========================================

Script E:\My Documents\Sat-tech\Rom 102 unlocker\new.xvb Transmission Completed

[ghost1412]

I just get a multimeter could you please help me on how I should mesure the Ohm on my unlocker as I never used a multimeter before ? Could you give me how to please?

[ghost1412]

does any one have an idea about how i could solve this problem ??

[Crazy1_79]

are you gettin provider unknown in nagraedit? look for the omni unlocker force fubar file that goes with the rev 242, DO NOT GLITCH THE CARD ANYMORE, IT WILL LOOP

[ghost1412]

This is what I am getting when I try to read my card

ATR: 3F FF 95 00 FF 91 81 71 FF 47 00 44 4E 41 53 50 31 30 32 20 52 65 76 32 34 32 62
CAM Type: ROM102 Rev242
Setting IFS
Provider: Unknown
Reading Card image...
Failed to read card. (Retries: 25)

[Crazy1_79]

http://dssftp.com/files/index.php?m=category&CATID=49 File number 3 is the one you want, you have to extract using winrar otherwise it will like the file is empty

[ghost1412]

I am running the file now and hope that it will open it up I will post the output

Thanks you

[ghost1412]

it is still runing over 45 minutes now should I let it go more than that ?

[Crazy1_79]

not very familiar with the file, but I think I would try adjusting delays or something.

[Crazy1_79]

try raising the VS1 from 10 to something higher, maybe even 95, changes the amount of tries LS1 from 40 to 200 it will take longer on each delay and maybe fix, be sure you are using the repair or fixing program not the unlocking program, I'm not sure of the options the script has, I've never used it.

[ghost1412]

their is no options for this script it is only running as unlocking their is no option for repair or fixing I did change the setting as per your reconmendation and I am trying it again now and hope that it will work
I will post the output again
Thanks you

[ghost1412]

it is still runing over 1 hrs with the new setting as you mention and no luck should I let it go more than that ??

[ghost1412]

This is what I get after a while still no luck



Buffer Intercept Installed. Trying to Open the 102.... Delay:0401 VCC:05 Glitch Type:06

Elapsed = 01:08:53

---------------------------------------------------------------------------------------------------------------------------------------------------- Rst1A----- Rst18----- Rst16---------- Rst11------------------------ Rst06------------------------------------------------------------------------------------- Rst3A--------

Sc.Read: Timeout Reading Data From Card - 2 Bytes Requested, 0 Bytes Read, Continuing Script

Script Error on Line 139
Sc.GetByte: Requested Byte Exceeds Last Read Request