can this card be fixed

[two-dogs]

I was writing a bin to the card and have way through I got an error and now the card reads like this
ATR: 3F FF 95 00 FF 91 81 71 FF 47 00 44 4E 41 53 50 31 30 32 20 00 00 00 00 00 00 17
CAM Type: ROM102 Setting IFS
Provider: Unknown
Reading Card image...
Failed to read card. (Retries: 15)
Is there any hope please help ............thanks...........two-dogs

[dw7]

Try wriiting the original bin back to the card

[woods]

what revision is the cam at? you can try the omin unlocker. i have had good luck with it on fixing provider unknown cams. needs to be a rev 107 or less i believe.

woods

[two-dogs]

I have tryed that program but with no luck do you have different settings that you use/ And for the rev it was at 107 but now it does'nt show a rev. And I tryed to write back but it just reads ATR: 3F FF 95 00 FF 91 81 71 FF 47 00 44 4E 41 53 50 31 30 32 20 00 00 00 00 00 00 17
CAM Type: ROM102 Setting IFS
Provider: Unknown
Reading Card image...
Failed to read card. (Retries: 15)
Unlocking Card...
Error
see no rev

[woods]

did you try and write a virgin bin back to it without reading it? or is is a sub that you need to read?

[PC_works]

Same problem to except rev 108

ATR: 3F FF 95 00 FF 91 81 71 FF 47 00 44 4E 41 53 50 31 30 32 20 52 65 76 31 30 38 6F
CAM Type: ROM102 Rev108
Setting IFS
Provider: Unknown
Installing Temporary Backdoor Patch.
Temporary Backdoor Patch could not be installed!
Failed to write card. (Retries: 15)

I tried to write a card and got an error in the middle of the write. i wrote 1 other card no problems with just before. both cards were virgin 102 rev 103

not sure what to do? i tried writing the virgin image back but get an error in nagraedit.

[PC_works]

I'm trying Omnirebel - stuborn fix (with modded MIK III) newd 13 flash. 220 ohms

This is the reading I'm getting:

Buffer Intercept Installed. Trying to Open the 102.... Delay:03C5 VCC:F2 Glitch Type:09
Elasped = 00:11:21
RstF2 RstF3 RstF4 RstF4 RstF4 RstF5 RstF6 RstF6 RstF6 RstF7 RstF8 RstF8 RstF8 RstF9 RstFA
RstFA RstFA RstFB RstFC RstFC RstFC RstFD RstFE Rst14 Rst14 Rst15 Rst16 Rst16 Rst16 Rst17
Rst18 Rst18 Rst18 Rst19 Rst1A Rst1A Rst1A Rst1B Rst1C Rst1C Rst1C Rst1D Rst1E Rst1E Rst1E
Rst1F Rst20 Rst20 Rst20 Rst21 Rst22 Rst22 Rst22 Rst23 Rst24 Rst24 Rst24 Rst25 Rst27

is this normal is should it have some ++ signs as well, What should I look for? thanks in advance for your help.

[asd12345]

PC Works me and u r floating in the same boat im getting the same problem as u. if i fix mine ill tell u how and if u fix urs u can tell me. finally so glad 2 c im not the onli 1 with that prob

[PC_works]

same here, i wrote 1 card no prob, 2 nd errored out during the write. still glitching. i'll post what worked (or not). trying different ohmn settings.