stumped

[broadway27]

Rom 102, Rev 245 found.

Sc.Read: Timeout Reading Data From Card - 2 Bytes Requested, 0 Bytes Read, Continuing Script

Script Error on Line 402
Sc.GetByte: Requested Byte Exceeds Last Read Request

this is what im getting in winexplorer 5

what should i do next??
white nexus
pot setting @ 700 ohms

[jmf38]

did you try nagramaster? i don't know if it will work with rev245.
do you know what rev245 is equal to in DN rev's?

[broadway27]

trying it right now....its an AA-07 card, to spoof a bell card. I can flash the nexus no problem, but not sure of the pot settings i should be trying....60 5 1 on NewD13 for timing settings....but dont know where to start on pot settings
Thanks

[jmf38]

i unlocked my 311 with a white nexus(newd13).switch 2 and 5 on
using nagramaster.
the trick is to turn the pot(slowly) counterclockwise until the script stops then back it off a little until the script starts running again.
example------------------------------------------------------------------------------------------------------------------------------------------------------------------------
the above is NOT what you want.
i also watch the led light as i am turning the pot(counterclockwise).it will start dimming. if you turn the pot to far the script will stop and you will have to start again. once pot is adjusted just right you will see letters something like rst01----rst08---rst21 rst10----.
once you see the letters frequently let script run and it will say success.(mine took maybe 5-10 minutes.)(probably 10 minutes)i had to adjust the pot several times til i got the letters to start scrolling rst26---rst,rst08-----rst---etc.
if you see a whole bunch of -------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- turn the pot just a hair until you see the letters scrolling again.
once you see frequent letters, let the script run.if it doesn't pop in 15-20 minutes.stop(abort) to let your nexus cool down,the pot will get hot.
let it cool down and try again.good luck!

[broadway27]

trying it...not getting any ------------- dashes.....getting Rst2ARst2CRst2FRst etc...no dashes at all seen
any ideas? been going for 15 min now

[jmf38]

let it go for another 10 minutes.sounds like pot is set right. you will notice the pot will get hot. that's normal but you should let it cool(abort) if nothing happens in 10 minutes. it will work. sometimes it takes a time or two

[broadway27]

60 5 1 timing setting on xpatmel right?

[jmf38]

yeah that's the default setting

[jmf38]

you can try 12V also
if 9V doesn't work.

[jmf38]

some guys will let em run for an hour but i would go no longer than 30 minutes.
let nexus cool-try again.
there is also another program. i'll try too find it for you.
you will glitch it, it will work

[broadway27]

what pot setting should i be at???thanks for all your help so far by the way!!

[jmf38]

everybody has a different method. that's how i was taught.
i use 12Volts to power my nexus with that method.
i'm just not sure if nagramaster will do a rev245.
let me look around a little. do you have a 12V power supply?

[broadway27]

yep...ive opened it before when i first got it...was only spoofed i think its called....but only by luck...not even sure how i did it....good atr and all...so unsure

[jmf38]

read the thread called 311- can't glitch it
read the bottom post.
your welcome! there is a file called something like Mr.Undo2.
guys are posting good results.
i'm not sure if that's the name but it's something like that.
i'll try to find it

[jmf38]

did it work? or are you just saying you got it to work in the past

[broadway27]

no it worked when i first got it......but i dont know the pot setting....it was at 9v....but i remember the dashes going across the screen , but dont see them now no matter what i do...

[jmf38]

here is something i found


I have opened 15+ DP311 receivers (REVs ranging from 281-286) with a White Nexus, set at 215 ohms, 11vDC power supply @ 800 MA.

Left chip onboard, cut the traces. Wires all 4" long.

I use Mr.UltiimateN2 unlocker at default settings. Every box has popped in less than 10 minutes for me. I do still have 1 stubborn box that refuses to let me in @Rev 283.

Wiley

[jmf38]

let nexus cool down for now

[broadway27]

what would i set rev to?

[broadway27]

unplugged now.....asking for nd30

[jmf38]

your rev will go back to what it was after you glitch it. i had cards spoofed to rev106(locked) then after unlocking they read as rev103.
here is something else that i found.


Mr.UltimateN2 is a program, not an unlocker. Also known as MRUN2.

Works well with my White Nexus.

~Wiley~

[jmf38]

when my 311 unlocked,
i wasn't getting -----------------------------------------------
just rst#'s like rst8rst21rst01,etc. then it said success.
just be careful that you don't burn up your pot. does it read with an ohm meter still-check it (with no power) on your nexus with a meter

[jmf38]

what is asking for nd30?

[broadway27]

so still use nagramaster? confused there a bit....i have it here, but it wont allow me to unlock??

[jmf38]

try nagramaster again. like you did first time. close nagramaster first then reopen it and try it again. turn your pot a little clockwise to see if you get--------------------------------------------------------- then adjust it like you did a little bit ago
is the nexus cooled down?if so try it again

[broadway27]

not warm if thats u mean....:-) ill try again right now...
is there any difference using loader version or regular 2.0?

[broadway27]

do i need to change the numbers at the bottom?? leave them as the default, right?

[jmf38]

use loader version,leave #' alone,try it again-good luck this time!

[jmf38]

mine says nagramaster vers 2.0(loader version)
click on tools,click on unlock card-glitcher
push unlock to start

[broadway27]

noticed something...same readout at pins 2 and 5 up as 1 and 6 up
not good?

[jmf38]

use 2 and 5 to unlock
use 1 and 6 to flash nexus
use 2 and 5
is your nexus pot pretty warm, that's normal
are you still getting rst10rst08rst21 etc.
if so your script and pot settings are o.k.
adjust pot slowly(when you do) we don't want to loop card.
the script will warn you first
don't make any sudden changes!
i just bought 3 311's from mili. they are user friendly-easy to program.
they won't do BEV though.

[broadway27]

still getting that...20 minutes now....adjust while its running right?

[jmf38]

yes but very slowly.
what happens is when the script is running,the loader heats up and your ohms settings drift a little.(the loader becomes unstable).a very slight counterclockwise adjustment(very slight) will either stop the script or unlock your card. you will notice as you adjust pot counterclockwise that the LED light will almost go dim. if it goes too dim script will stop and error out.
if you can get it just right the led light will almost start blinking but not brightly-it'll just slightly flicker.and a bunch of rst#'s will scroll.
if you get alot of -------------------------------------------------------
then you need to adjust(counterclockwise).
the more counterclockwise that you go, the more amperage is going to the card.they say you can loop your card but i haven't yet looped one with nagramaster and i have had good luck so far.
i replaced the little pot with a bigger one 1/4 watt with a knob on it to make it easier to adjust and that pot gets warm-hot too!
you may want to try 12 volts. it works for me 5-10 minutes.
some guys are putting there cards in the refrigerator then unlocking them.
just don't let your loader get too hot. i have had mine pretty hot and it's still doing well on tough cards etc.

[broadway27]

the rst# are not scrolling i notice....when they reach the right side of screen, thats it...nothing updates....unsure what that means
also, how far does the VCC go to?
having a blast here....thanks again for the assistance~

[broadway27]

also..the rst #s come up even when i have 1 and 6 up....forgetting to put 2 and 5 up when glitching

[gooding]

Well I dont have a white nexas but might try 400 ohms on pot and dip 4 down ! Just a thought . Works on blue nexas .:)

[jmf38]

did it work yet?
you might want to try a newer type of winexplorer script!

[broadway27]

nope ..not yet...still unclear why the Rst#s are the same with 2 and 5 up as 1 and 6 up

[broadway27]

im getting bad cmd04 as well in winexplorer....can rest atr in nagramaster no prob....but still no dashes and pluses...even when i adjust pot
anyone with ideas to try?? pot is set at 700 ohms

[broadway27]

how far should the VCC go to?

[broadway27]

why am i getting bad cmd04 response?

[broadway27]

and why cant i get dashed and such.....
:-(

[broadway27]

why am i not getting dashes and pluses with my unlocker??? comes up with rst4c etc...but stays like that for 20 minutes or so....using nagramaster , and 700 ohms..
*sigh*

[jmf38]

broadway 27.
sounds like you have a tough one.
try 12 volts.
maybe someone can translate your rev(245) into DN rev#'s like rev,103 etc.
nagramaster will only work with DNrev105(maybe 106 i think) cards or lower.
i don't know how BEV rev#'s are = to DN rev#'s.
i think that's what you have right?
anyhow, a member told me to try 12volt and i had good luck with it.
my white nexus power plug is 12v+ center,and the outer plug is negative(ground).
i use a 2 amp power supply(they say you only need 600 milliamps).
any sufficient 12 volt adapter(power supply) should do the job.
it's worth a try. i had trouble unlocking a cardrev106 with 9V.
switched to 12V and it took like 5 minutes.
i think that the pot adjustment procedure that i posted earlier is o.k..(it works).so far so good.rev 109's can't be glitched yet-they will loop
that may be a good thing so DN will be happy that FTA,etc. is gone and leave the rom102's alone.(wishful thinking)
maybe someone can add some input,suggestion's.
the only suggestion that i can give you is to try 12volt with nagramaster.
your card is not looped cause you got ATR!
good luck again!jmf38

[jmf38]

i also had no luck with some winex programs. cmd-04 error etc.
my friend told me to go to the upper window in winex when it errors out and turns red.
and just delete the error(by backspacing) and run script again but i never had any luck cause another error would come back.
make sure that you read the(read me's) before running a script.
there are certain scripts for different rev's.
i would try 12v-Nagramaster

[broadway27]

Im not having any luck.....just a thought though....does it matter what the original rev was when the card was first opened?? i wrote a virign bin to the card to go from dish to bev.....and then applied the 245 blocker....maybe i should try dish revs?? was a 103 i believe
any ideas?

[jmf38]

did you install a BEV bin?
cause if you installed a 245 blocker than you should have a password to unlock card. if card is locked then you won't be able to write a dish(or any bin to the card.
let me know something!maybe the card isn't locked.
if it is locked,than maybe you can open up the(245) bin file that you wrote to the card(with nagramaster) and see what the password is then try to unlock card with your password in beta9 using the tools-unlock card function.

[DoubtingThomas]

i would try 12v-Nagramaster

I have seen numerous recommendations about the voltage levels. Do these unlockers or even modded unloopers not use a voltage regulator to ensure that the incoming voltage is within tolerances ie 5v ? If so why using 12v rather than 9v makes any difference as the voltage in circuit would be 5v.

The only thing I could see is that with a 12v the milliamperage would be higher.

[broadway27]

i found my bin download...but password didnt work in anything i tried...still plugging away with unknown provider error rom102rev245

[jmf38]

you didn't exceed the password bytes-did you?
0 thru 7(9?) and A thru F.
there is a good thread on unknown provider.
i did burn up a pot at 12 volt. now, i use a 3 watt 15 turn pot-5K ohm on my nexus.
i can run 12 Volt at certain rev's.
do you have an ATR? if so, i think you can revive it.
you did save your original bin right?if so you can rewrite the first 2 bytes ex.AF BF @ 30C0.
Theres also a script to where you can get rid of unknown provider!
hope this helps!-jmf38
you need to check the pot on your nexus with an ohm meter(both sides since middle is ground). also i was getting unknown provider with an old iso. let us know-your card may be o.k.
and maybe nexus just needs a little maintenance.-upgrade

[jmf38]

broadway,
any progress?-jmf38

[bamfordb]

I just stopped in to tell you that you CANNOT unlock a card at rev 245!!!!! I am suprised that noone has told you that yet. Stop what you are doing and start reading and may be the card will someday be of use ( if you have not looped it already)

[jmf38]

thanks,
I had no idea on the bell revs.
broadway,hold on to that card- i don't think that we looped it.
it's just not unlockable at this time.
heck, i didn't know all this time.
what's next broadway? another card or a mili 311 is a good deal.
talk to you later!
thanks bamfordb!
jmf38