thadeus
08-08-2006, 08:23 PM
So I've had my white nexus for almost a week now. Took 5 days to ship and came with a case (was worried about that one). And I was pretty stoked to start popping cards. Of course i didn't touch the actual loader the first two days cause I wanted to be sure not to loop my card so I've read everything I can find on this card and loader and so far my understanding is that it and the rev105 are basically the same to glitch into so I've been trying to get this card to pop using methods described for both.
I have only been using winexplorer and so far I have used the following scripts:
ROM102_ND13_A0FF-INTERCEPT-autoVCC_20 edited for great unlocking.xvb
ROM102_ND13_A0FF-INTERCEPT-autoVCC_20.XVB
RebelSerf 102 OmniUnlocker.xvb and New.xvb
In each script I have played with the mix and the delays trying all the values that have worked for others.
For power I'm using a 3~12 volt 800 mA power supply. I have tried switching from 7.5-9.0-12.0 but it didn't really seem to make a difference.
I think the main problem I'm running into is with the pot. That little screw is sooo jumpy and difficult to manuever it's ridiculous. I have been using an ohmmeter and from what i've read the Pot should be set somewhere around either 195-220 or 18-30 for a 241. This is hard to do. I can get the pot around 200 or so but i can't really move it up or down an ohm so this makes testing difficult. Plus I'm a first timer so I'm not sure exactly what I'm aiming for.
The only half success I've had was around 20 ohms where I got some +--+--+ stuff before the cmd04 which means the resistance is too low. So I played around that area for a good 6 hours to no avail.
And yes I'm glitching with 2 and 5 down (sometimes tried 4) and I've flashed Newd13 with 1 and 6 (timing changed)
So my questions are:
1. I have read of success with nagramaster 2.0 and 1.0 glitching into these cards. But I have also read of some looping. Are these programs relatively safe to use if you have an idea what values to supply? And what of other programs like T-REX and FTAPirate.tv?
2. If I go to low on my pot like below 15 will I likely loop my card? I've been careful to stay above 18 but i'm thinking i may have to go lower?
3. Is it normal for my potientiameter to have a different resistance after an unlock attempt than it had before?
I have only been using winexplorer and so far I have used the following scripts:
ROM102_ND13_A0FF-INTERCEPT-autoVCC_20 edited for great unlocking.xvb
ROM102_ND13_A0FF-INTERCEPT-autoVCC_20.XVB
RebelSerf 102 OmniUnlocker.xvb and New.xvb
In each script I have played with the mix and the delays trying all the values that have worked for others.
For power I'm using a 3~12 volt 800 mA power supply. I have tried switching from 7.5-9.0-12.0 but it didn't really seem to make a difference.
I think the main problem I'm running into is with the pot. That little screw is sooo jumpy and difficult to manuever it's ridiculous. I have been using an ohmmeter and from what i've read the Pot should be set somewhere around either 195-220 or 18-30 for a 241. This is hard to do. I can get the pot around 200 or so but i can't really move it up or down an ohm so this makes testing difficult. Plus I'm a first timer so I'm not sure exactly what I'm aiming for.
The only half success I've had was around 20 ohms where I got some +--+--+ stuff before the cmd04 which means the resistance is too low. So I played around that area for a good 6 hours to no avail.
And yes I'm glitching with 2 and 5 down (sometimes tried 4) and I've flashed Newd13 with 1 and 6 (timing changed)
So my questions are:
1. I have read of success with nagramaster 2.0 and 1.0 glitching into these cards. But I have also read of some looping. Are these programs relatively safe to use if you have an idea what values to supply? And what of other programs like T-REX and FTAPirate.tv?
2. If I go to low on my pot like below 15 will I likely loop my card? I've been careful to stay above 18 but i'm thinking i may have to go lower?
3. Is it normal for my potientiameter to have a different resistance after an unlock attempt than it had before?