Unlocking Rom 102 Rev 103

[berniebutt167]

I have tried Nagramaster 2.0 it goes for 2 seconds says unlocked so i tried to write still locked, From reading i understand that it might be marked, so i have tried omniunlocker stubborn fix, i have also tried to run A0ff Interceptor with no luck anyone have any ideas to get this card unlocked....

Oh ya also forgot to mention that i have the new white nexus unlocked and am using anywhere from 600-1200ohms with both 2 and 5 in the on position thanks

Bernadette

P.S. no its not looped yet it gets a good atr so thanks

:)

[Crazy1_79]

well try the aoff intercept one again, change delays to 320 and 350 vcc start to 15 and limit to 0. It will jump up to 40 vcc unless you change the vcc lower in the script too. but if you increase try count to 200 it should be ok.

[berniebutt167]

ok i did that it now has gotten a good glitch, now what should i use to write a new image to the card, i was able to get it to do this once last night with stubborn fix, and when i did that i used the rom10X writter program it got half way on writing the new image then said it cannot write like 98c0 so then i tried card in my programmer and it is still locked, is there something special to writing a marked card thanks

Bernadette

P.S. Thanks for your help :)

Here is the logs of nagramster and the logs of the glitch and the log of it failing i am using nagramaster 2.0 loader version and am writing a clean virgin rom 102 rev 103 image to card after glitch and thats all i get is failed :( please help

TX Data : A1
===========================================
Glitch Success!! A0FF-INTERCEPT IS ON
BootLoader 6F 00 RSP Received!!
VCC = 13 (~0.363725490196081 vdc)
Glitch Delay = 0350
Glitch type 09
===========================================
Script C:\Dishnetwork\Unlocking\ROM102_ND13_A0FF-INTERCEPT-autoVCC_20\ROM102_ND13_A0FF-INTERCEPT-autoVCC_20.XVB Transmission Completed

Timeout from 2A command
The Update Status Word is at 0 (Decimal)
The Fuse Byte is at 0 (Decimal)


here is the failure of nagramaster (AKA address write fail)

Submit this failed Write report for support:
Write Failed at Addr: 9FC0
$3170 = 4003880030100114050060DB9A400060
$3180 = DB8219008859807500812B80A0008AB3
$3190 = 80C80000000000000000000000000000
$30C0 = A7BF8703808000000000000000000000
$8219 = 9D9DA1FF2703879D9DBC889D00000000
$9A40 = A1FF270187CD5A7D0DFA8080BC800000


9FC0 FAILED ? Please help.

[udntcme]

try n2edit 2.55 read cam after aoff intercept installed....do nothing else between this procedure.

[berniebutt167]

ok i went ahead and did the a0ff glitch again and right after it finished i opened up n2edit 2.55 clicked on read card and i got a valid atr with valid rom2rev103 detection. Here is the rest
provider unknown
reading card image
failed to insert boot loader
failed to read card

Thanks again p.s. i am using the glicher with n2edit
and it has the two red leds on when reading the image that time.

[udntcme]

Are you trying to read/write with your loader.....???You should use an "ISO " programer...All the best.Also Unknown prov =Prob looped need to now use rebel stuborn fix script to get provider back....All the best...