White Nexus DP311 Rev 283

[prnybk]

hi all i got the white nexus from mill and flashed it

but i'm running into an issue using nagra master 2.0 loader version

i have the passive card plugged into the nexus pin 2 and 5 are ON all others are OFF

when i click on unlocker (glictch)

i get -+12+3F-+12+3F-+12+3F and it keeps going like that


just wondering if that is correct because i let it run for over an hour and still nothing


thanks for all the help


update ok now it's showing -+CF-+CF-+CF-+CF-+CF

no more -+12+3F-+12+3F-+12+3F

[mechanicman]

i opened 3 rev 283 with same clear milli unlocker. i used approx 70 ohm pot and nagramaster. it did take approx an hour or more.

[prnybk]

i opened 3 rev 283 with same clear milli unlocker. i used approx 70 ohm pot and nagramaster. it did take approx an hour or more.


Humm ok but what i'm talking about is the responds that i'm getting back



are they correct or not correct
every time i change the pot i get one of the 3 lines below


-+12+3F-+12+3F-+12+3F

-+CF-+CF-+CF-+CF-+CF

+12+C8+12+C8+12+C8+!@

[mechanicman]

i was getting on your first line of your post.. i just left it alone and it would pop. i am using 14 volt adapter, 70 ohm pot measured on left two legs of the pot. using nagramaster.

[prnybk]

i was getting on your first line of your post.. i just left it alone and it would pop. i am using 14 volt adapter, 70 ohm pot measured on left two legs of the pot. using nagramaster.

ok you mean this line:

-+12+3F-+12+3F-+12+3F


i will try to get it like that agin and let it run for an hour or 2 and see what happens

[Zim]

yes @ 50 -70 ohm, used new.xvb,.... keep wires as short as possible

[prnybk]

yes @ 50 -70 ohm, used new.xvb,.... keep wires as short as possible

ok that new.xvb thing and winexplorer doesn't work

what i am using with the results that i'm getting now is Nmaster 2.0 loader version that one i have been getting the best results with

that new.xvb thing all i get is -----------------------------------

no RSP ++++++++ or anything

[mechanicman]

nagra master opened 3 rev 283. i had to put one rev 283 chip that was mounted on a interface card in the freezer for 10 minutes and then it popped in seconds when i quickly stuck it back in the nexus.. dip 2 and 5 on... i am using 14 volts (positive center plug) adapter even though its a 9 volt adapter.

i would change delay start to 340 and delay limit to 350.. left everything else the same. this is what worked for me..oh and i did change out the pot as i burned it up by setting it to low.. i bought a 5K ohm pot from ratshack.. little blue one with three legs..i measure pot with ohm meter on the two left legs of pot. i used 70 ohms for the rev 283s

all my chips are mounted on boards with short wires..

two rev 283 i just left running and went to lunch as i got tired of watching for them to pop. when i returned home they were open..so maybe an hour or two..
i change to my iso and ran n2edit and read and save images..

[exploreworld]

"My first Glitch" Looping two ROM's 102 Rev 103, 105, in the process, I was able to succesfull open a 311 Rev 283 in less than a minute using nexus blue cranking the voltage to 12 V (center +) and adjusting the pot around 2K Ohms. Be careful with this seetings on Rev 103 & 105 That's how I think I looped them. I get no ATR reding on both cards after I tried glitching them. Is that the message you get when you loop the card? If it is then they're looped.