Yellow N2 WITH 4619 chip. Unlocking 311?

[ahmar03]

Hi, I give up! My Mikabu n2 suxs! It won't unlock my 311's both 283's. I have read everything. Change the pot to 700.. Rst is there but no luck. Ran the Naragmaster for 2 days. Nothing happend. Ran new.xvb file nothing for 24 hrs. Whats next. Don't have a nexus t911. I have a N2 mikabu with 4619 chip. Please somebody adivce me to the next step for this 311's to be unlocked.

Got modded All traces cut. Have cardless interface. NO luck on unlocking. Please help.
Thanks.

[Crazy1_79]

well what about the rom102interceptautovcc20? did you try that? that will run vcc from 40 to 0 continuously. it will start at 90 for a vcc, try lowering delays to 0320 and 0350, it isn't the locker maybe the mik2 wasn't the greatest unlocker but will pop those revs if used right. If you don't understand waht I mean by changing delays or vcc's do a search on it. you will find your answer. pay attention to the responses from the card, it should have something like --++--++-------++++----+++ you want ++ and -- for a card to glitch properly at that rev.

[mtmt1us]

Hi, I give up! My Mikabu n2 suxs! It won't unlock my 311's both 283's. I have read everything. Change the pot to 700.. Rst is there but no luck. Ran the Naragmaster for 2 days. Nothing happend. Ran new.xvb file nothing for 24 hrs. Whats next. Don't have a nexus t911. I have a N2 mikabu with 4619 chip. Please somebody adivce me to the next step for this 311's to be unlocked.

Got modded All traces cut. Have cardless interface. NO luck on unlocking. Please help.
Thanks.
I did a setup like yours and had same trouble.I ended up downloading a prog. called rom102unlocker ver 1.0.When you run this one turn pot down(I think to the right)When the program errors out turn the pot setting back up just a little bit then start prog. again.Now after a minute or two you should start to see more +++++'s than before and just sit tight,and don't fool around with pot and it will crack.If it does not ,try to wire the loader directly to reciever with very short wires.I had tried nagramaster and winexplorer with no success even with Mikobu wired directly to reciever.I am curious if rom102unlocker will work with the interface(mine was already wired directly before trying it).Please post back with your results.Good luck.

[mtmt1us]

Ran new.xvb file

Oh yeah I just remembered, I flashed my mikobu with newd13 not new.xvb. I don't know if this makes a difference.

[ahmar03]

Still no go.. Whats the deal?

[mechanicman]

ok try this.. well i had my chip out of the 311 on a passive interface card. it was a rev 283 and would not pop using nagramaster. and 70 ohm pot.. i put card in freezer for 10 minutes and then with same settings ran nagramaster again and it popped in seconds!!! i did 2 other rev 283 and they all popped but after about an hour....

[hunteriam]

I purchased one of these loaders, unlockers probably four month'ls ago and still have never got it to work. I flashed with n2 13 as you did and have tried everthing I know to do and it just sucks. I have ask for help with this, but only get the response to read, well I'v e read and read and the truth is it sn't worth two cents and it will never work. NOw....... Please someone prove me wrong and take this reading bull somewhere else and help those who have paid good money, but just can't get it. I'm not the smartest person, but have messed with testing enough to know that there is more to the story than is being told. I have had to send out my only two cards to friends and pay to have them unlocked when I paid very good money for a unlocker that should have done just that. As I said if I'm wrong please someone show me I'm wrong, but until then I feel I have been sold something that just isn't worth a crap.

[ahmar03]

well i have popped 103 105 with the n2 mikabou.. I played around with the pot settings. I turn completely to the right and a tab to the right in 15 20 my card popped.

[ahmar03]

im still working on the 311 283. But im trying to deep freezer thing.. Post results. ASAP!;

[mtmt1us]

I purchased one of these loaders, unlockers probably four month'ls ago and still have never got it to work. I flashed with n2 13 as you did and have tried everthing I know to do and it just sucks. I have ask for help with this, but only get the response to read, well I'v e read and read and the truth is it sn't worth two cents and it will never work. NOw....... Please someone prove me wrong and take this reading bull somewhere else and help those who have paid good money, but just can't get it. I'm not the smartest person, but have messed with testing enough to know that there is more to the story than is being told. I have had to send out my only two cards to friends and pay to have them unlocked when I paid very good money for a unlocker that should have done just that. As I said if I'm wrong please someone show me I'm wrong, but until then I feel I have been sold something that just isn't worth a crap.
What programs have you used and what resistance do you have the pot set to??I have mine set to 1600 ohms and it pops a card in 5 seconds with nagramaster.311's are a little harder ,but are doable with mikobu n2.