so far my best mod

[NICKY__6]

after 10 or 11 revisions this unlocker mod has so far not met a card it could not unlock and over 40 cards done not one loop


i find best results
103-105
nagrmaster
12v center positive
2 and 5 on
new13
2.2 on meter

106-108
same
rebel or rom10x script
2.6 ohm
2and 5 or 4 dip

MOST IMPORTANT I FIND THE BRAKE AND DIAL STAY CORRECT SO IF I TURN TO #2 I KNOW ITS 2.2 AND #4 I KNOW ITS 5.0
SO I CAN ADJUST WHILE SCRIT GOING AND KNOW MY RANGE


http://img135.imageshack.us/img135/3056/mymodsmalldv8.jpg

http://img154.imageshack.us/img154/9853/yippieko1.png

http://img291.imageshack.us/img291/9638/nbewunlock002ot6.jpg

[Crazy1_79]

Nicky where did you get that brake?

[jmf38]

nice job!
i just installed a 3watt 15 turn 5Kohm pot in my nexus. it is user friendly for those touchy script's. it will also handle 12v at low ohms well.
i also put a mini fan on top the case too keep it cool.
the pot is mounted above the fan.
for anyone that has burnt up the mini-pot.
MCM co. sells a nice vishay 3watt 5K pot(it is wirewound type)15 turn.
you just need to fabricate a plate or bracket to hold the pot cause the housing is too long to fit in the case.it works well @ $7.99

[Pyotr]

I've been looking for someone to help me out with modding my "modded" T-911. My brother usually does the soldering at my direction as my right arm doesn't work. He hasn't been able to do this one.Too busy or something.
Anyway,what I have is 2 surface mount 4619 chips and a new 5k POT.The original pot is mangled plastic.The new on is better quality. I also have some ChipQuik for removing the old 4053's.
I don't know how well these mods work,but this loader was able to pop both a 101 rev 007 and a 102 rev 105.Not bad.I don't really have the dough to buy a new loader either.Anyone got someone in mind who might want to do this?

[jmf38]

try it!
if dough is low (try the pot first then the 4619's)
i would put the pot in first,see what happens-it may work fine.
good luck!jmf38

[NICKY__6]

my honest opion if u dont have any over rev 105 and dont have a good amount of experience soldering dont try the chips very very small and u need to be good

as for chip wick what a waste of 100 bucks nothing works better then a good iron and a roll of solder wick ive done 30 or 40 so far of these for people and let me tell u a quality pot is the real deal i have tried cyclone and new mik and nexus blue this out performs them all those are also great units but this has done all rev 107 and 108 and nothing took more then a few min

that yellow mik i had fitst is a pos and they schoul recall that thing

[jimwang111]

after 10 or 11 revisions this unlocker mod has so far not met a card it could not unlock and over 40 cards done not one loop


i find best results
103-105
nagrmaster
12v center positive
2 and 5 on
new13
2.2 on meter

106-108
same
rebel or rom10x script
2.6 ohm
2and 5 or 4 dip

MOST IMPORTANT I FIND THE BRAKE AND DIAL STAY CORRECT SO IF I TURN TO #2 I KNOW ITS 2.2 AND #4 I KNOW ITS 5.0
SO I CAN ADJUST WHILE SCRIT GOING AND KNOW MY RANGE


http://img135.imageshack.us/img135/3056/mymodsmalldv8.jpg

http://img154.imageshack.us/img154/9853/yippieko1.png

http://img291.imageshack.us/img291/9638/nbewunlock002ot6.jpg


I removed chip from board to plastic frame, it’s 811 rev 283 chip. I have an orange nexus.Use Nargramaster 2.0 Loader version, , newd13 flashed. Good ATR. 12V. but always get C6+12+C6,unlucky to get it unlocked, can you help me, or is it possible I pay you to unlock it for me,please?

[jmf38]

good ATR is good-not looped!
maybe the pot is burned up-maybe not.
try omni or rebel script.

[Pyotr]

my honest opion if u dont have any over rev 105 and dont have a good amount of experience soldering dont try the chips very very small and u need to be good

as for chip wick what a waste of 100 bucks nothing works better then a good iron and a roll of solder wick ive done 30 or 40 so far of these for people and let me tell u a quality pot is the real deal i have tried cyclone and new mik and nexus blue this out performs them all those are also great units but this has done all rev 107 and 108 and nothing took more then a few min

that yellow mik i had fitst is a pos and they schoul recall that thing

Chip Quik was free sample

[al bundy]

after 10 or 11 revisions this unlocker mod has so far not met a card it could not unlock and over 40 cards done not one loop


i find best results
103-105
nagrmaster
12v center positive
2 and 5 on
new13
2.2 on meter

106-108
same
rebel or rom10x script
2.6 ohm
2and 5 or 4 dip

MOST IMPORTANT I FIND THE BRAKE AND DIAL STAY CORRECT SO IF I TURN TO #2 I KNOW ITS 2.2 AND #4 I KNOW ITS 5.0
SO I CAN ADJUST WHILE SCRIT GOING AND KNOW MY RANGE


http://img135.imageshack.us/img135/3056/mymodsmalldv8.jpg

http://img154.imageshack.us/img154/9853/yippieko1.png

http://img291.imageshack.us/img291/9638/nbewunlock002ot6.jpg

whered you get the pot at? any kind of model number. thanks