SAT 119 . Where are you

[FRESENG]

Hi Crow 492.

I can get 110, but not 119.

I have a Vieusat xtreme with dish 500 two double lnb legacy. swith 4x1 119 on port 1- 110- on port 2- Bev 82 port 3- Bev 91 port 4. Have another separate receiver with a 4x1 switch,same situation can't get 119. Did tried direct connection from dish to receiver , still same problerm. It is 119 gone? any other ideas how to fix this problem.

Any help will be apreciated

Thanl you

[atigrado]

I edited the keys and satelite scaned in my fortec... now, All open (119 working.)

[FRESENG]

Did it . not working . Aloso did change cables . Satill not getting it. When I go direct cable I can get it , with swich no way.

[atigrado]

When you do satelite scan... some times 119 have to be in tone B and 110 in tone A. (or #1 or #2)

Try with that...

[Sulten]

119 TP may want to scan 12239 and if this is FTA when you are in the antenna setup and are on 119 make sure the top right says 119 and not 110. it happens and then you will be scanning double sat

[gap212]

I have same problem....i used disecq and switch 21, all i'm getting is 110 no 119. It's fu**** viewsat problem i think...some say u must have burn ur switch. I don't think so. Also i'm getting all channels in double....this viewsat is all messaged up. I tried 10 diff. pgm file but still same issue.

[FRESENG]

Hhave a Vieusat xtreme with dish 500 two double lnb legacy. swith 4x1 119 on port 1- 110- on port 2-or A -B. Does not work. I have my pansat and never have problems to set it . I bough this new Xtreme and I can not figured why sat 119 is not working . Is there any problems with viewsat to get 119 bird?

[gap212]

119 TP may want to scan 12239 and if this is FTA when you are in the antenna setup and are on 119 make sure the top right says 119 and not 110. it happens and then you will be scanning double sat


HOw can i change that upper right hand satellite info...i rebooted system, uploaded new pgm. The thing is when I scan 119 on upper right had corner i see 119 so i go ahead and do a F1 scan satellite. But when I go to scan 110 i see 119 and i can't get to rid off that...so i'm getting double channels and 110 doesn't work. If i scan 110 first than 119 is all fu***.
HOw can i resolve this prob....

[Russellh2o]

sometimes its best to hook up 119 direct to reciever tune your antenna till it says 119 in the upper right side of setup screen...then check 110 and see if its still tuned ...then scan sats..for your channels worked that way for me

[FRESENG]

Rusell.
sometimes its best to hook up 119 direct to reciever tune your antenna till it says 119 in the upper right side of setup screen...then check 110 and see if its still tuned ...then scan sats..for your channels worked that way for me

How do you check the 110 bird , with the disq swicht and the 110-1129 all toghether or directly. Can you explain more pls.

Also can you tell me what bin are you using?

Thanks

[Russellh2o]

under installation scroll your satellites till you find the sat you have the individual lnb for 119 or the other lnb for 110 depending on signal the sat will be shown in the upper right side when you find the 119 that way change cables to the lnb for 110 and scroll the sat selection to the corresponding sat if your antenna is setup correct it will tell you if your on the sat you selected...if not you may want to set your antenna for azimuth elevation and skew once you get the correct settings the ID should match for what ever lnb you select
i am running the DBPSW-060814ES file with autoroll on

[FRESENG]

HI Russel .
the individual lnb for 119
I do have two doble legacy LNB. When th signal comes in the bar for 119 it shows a kind of red color. but in the 110 it shows green , I beleive both signals should show green. I did the scan individualy and I can get both sats this way,, but when I put both sats on ths switch Sat 1 fo 119 and sat for 100, only tha sat 2 (100) works . I also chang LNB , and cables, still not working.