Romcode 4.06f and 4.10h

[LPGAS4U]

I have a dp311 and I had it working with romcode before but now I cant get a cam # and it says it is locked with 4.10h but if I go back to 4.06f everything looks fine and it is unlocked but if I try to program it with 4.06f it says problem with 3m does anyone have any ideas

[Zim]

does it say unkown provider?

[omare]

I have a dp311 and I had it working with romcode before but now I cant get a cam # and it says it is locked with 4.10h but if I go back to 4.06f everything looks fine and it is unlocked but if I try to program it with 4.06f it says problem with 3m does anyone have any ideas


Don't get your versions mixed. If you programmed card with 4.6 CLEAN it with 4.6 BEFORE programming with 4.1h

Card should be open at rev103 before you attempt to program with new version.

That should keep codes appart from each version-

[JT]

Romcode is still telling me 4.06f is the latest......hmmm

[HOBO]

Problem with 3m is that you have selected tiers in tier editor that is already in the 3m bin.Uncheck the boxes that say already in 3m and try again.

[LPGAS4U]

I can program all my rom 102 cards fine but the dp311 wont anymore I can clean it in 4.06 and it shows a green lock but when I go to 4.22 it says it is dealer locked or stream locked and shows a red lock and when I go to nagramaster it says no atr but in romcode it has a atr any ideas

[Zim]

what version of nm r u using? and have u checked the comport?....also try using n2edit ...what u want to do is writre the original bin to it cleaned ofcourse so you can start over... if rc gives u atr then either other proggy should 2.....

[LPGAS4U]

I had computer problems and lost the original image a long time ago but it was working after that and now all of sudden it wont

[Zim]

woah! havn't came accross this before...if rc4.06 says it is clean then it should be....try programming with 4.06 and cleaning again see what happens....or try to readimage in n2edit, clean codespace and write that image to it....

[felicia]

I have asked this question before but got no replys so I need to ask again. When I try to program with romcode I get the message "failed to find blocker patch". Can anyone help me with this problem?

[vegasmax]

#4 (http://www.dssftp.com/forum/showpost.php?p=412717&postcount=4) http://www.dssftp.com/forum/firmament/statusicon/vbpager_icon.gif (http://www.dssftp.com/forum/showthread.php?t=67542#)
http://www.dssftp.com/forum/firmament/statusicon/post_old.gif 1 Minute Ago
vegasmax (http://www.dssftp.com/forum/member.php?u=57669) Online vbmenu_register("postmenu_412717", true);
Registered User
Join Date: Jun 2006
Posts: 25


I just programmed two cards with the new script....when I started programming the card a window poped up and said something like too much mertic data....I had to click on it 10 to 15 times to get the box to close....when it finally closed the card programmed and it said success and the lock turned red.

However, I don't get any PPV channels, all are very slow and some go off.
Anyone else having the same problem??? I think it may be a pot setting on my Nexus and suggestions???? Vegasmax

[drwolf]

Vegasmax,
Recheck your tier list and make sure you don't have any duplicated that are in the super 3m, that will cause that problem.

[Zim]

I have asked this question before but got no replys so I need to ask again. When I try to program with romcode I get the message "failed to find blocker patch". Can anyone help me with this problem?

Does it says "provider unkown" then you will need to write clean virgin image to it or atleast write a7bf in 30c0....

[felicia]

Thanks for your reply Zim. Yes it does say "provider unknown" but I thought I had changed 30C0 to a7bf. Also on the romcode website it says "no need for blocker patches" so why does it give me the afformentioned message?

[Zim]

not sure but I had this prob before and I wrote the original cleaned image to it a problem fixed....there is also a d2c script to reset the data pointers....but the clean image werked fer me....

[Zim]

ofcourse you need to check the use private bin if you are using it to remarry to the ird....if you are using your own bin (box keysand id) then no need for this.....