No Key1 Found

[slave2fishing]

I changed the setting.ini to reflect the new key and got black screen. I checked with nagramaster and it says no key1 found. Anyone know how to fix this?

[smilingjack]

look for them
Dish is they are hiding them
most programs don't work any more at fining them.

[Zim]

I am in the same boat...no matter what I do ...even if I write another bin to it with the proper keys it reads fine and shows both keys but when I program with romcode it seems to dissapear ...black screen and when I go into nagramaster it says no key 1 found.... I have treid just about everything and no go ...I have a quite a few cards and only 1 is doing this....please help....

[Zim]

k, got it!....if you write a bin grabbed of another card programmed with romcode even if it is an old key....and write it to the card then the key stays....can't understand why not just any bin will werk but this is what I did and it is up and running :)

[bigstinker]

How do you write another bin in romcode? Are you saying you took a bin from another PC with a romcode dir? I see private.bin and data.bin..
Pardon my ignorance but all I have ever used is romcode for 102 cards.

[nebur]

How do you write another bin in romcode? Are you saying you took a bin from another PC with a romcode dir? I see private.bin and data.bin..
Pardon my ignorance but all I have ever used is romcode for 102 cards.

he got several cards programed whit rome code what he did is read one card whit nagra master save the bin and then apply the bin to the other card, hope this help

[LocoMex]

I believe there is a sticky in RomCode section describing how to write new keys if you are using romcode. It says to clean card with Romcode. Open card with N2Edit and save image. Open Tierworks and write new keys. Then modify bin and write over saved image. Then write image to card with N2Edit. Then program with romcode. This is the long way to do a key change, but it worked for me. Before, I had the same problem. No Key 1 found. I tried everything with Romcode but could not get the Key 1 to write. Used the long method and it worked. Good luck.

[Zim]

he got several cards programed whit rome code what he did is read one card whit nagra master save the bin and then apply the bin to the other card, hope this help

This is excactly what I did....;)

[LocoMex]

While the ini file method of changing keys is quick, it is obviously problematic with some cards, mine included. Maybe Mili can contact the RomCode people and report this problem. I don't mind using the method described in the Sticky, I just hate fooling around with my card. I only have one and would hate to screw it up. Mili, if you have a chance, can you check on this No Key 1 issue? Thanks.

[slave2fishing]

Thanks LocoMex I was able to get running the way you described. I was surprised that programming again with RC didn't remove the key. Maybe whatever is in the stream takes it off these certain cards. Mine was rev103 BTW. I am in the same boat as you with only one card and really not wanting to loop it. Hope RC udates their software to mend this problem.

[EGG SUCKER]

ok got key 1 to work, clean card in rc, open n2edit read card save image,open up dt teir works, open key to bin, get keys, if it errors out put in the keys,save and write mod bin then open back up n2edit write bin back to card, check n-master to see if you have key 1. program with rc no bin,select your teirs,
make sure before you go threw the steps you have current updated tiers and not the old one or it will not work. most of all of us put the updated teirs in the ini of rc so we are ok, but I wrote my original bin back to the card so I had the old keys and did not pay attention to check and see if I had the new key in n-master. so be sure to check, good luck

[Bandit5906]

Bunch of cards and all worked with either method! I don't doubt you, but I have no thought as to what the problem could be. I go back and check the .ini file and both keys are there!

[mili]

Indeed I found a few cards that did nto like the ini method. It is beyond me why.

mili

[NoC]

Thank you Mili for your input. I knew that we're not the only ones that has problems with the ini method. I'm gonna wait for romcode's new update. Don't feel like messing with nagedit on the other methods of updating the key. I'm watching my FTA's in the meantime and waiting for romcode.

Indeed I found a few cards that did nto like the ini method. It is beyond me why.

mili

[jaicos]

Hi guys, just use Nagramaster 3.8 after clean with Romcode here is how
1) clean card in romcode
2) read card with nagramaster3.8
3) click the key icon on top (this will grab the keys and write them to the bin)
4) write bin to card
5) program card in Romcode (don't select private bin), only thing you have to do is select tiers and hit program
6) watch tv :D

[ceelo]

Hey I am not sure how to do the whole tier and romcode thing...but I always use nagra master....since the key 1 isnt working....I dont wanna risk me doing something stupid...will the nagra master update soon so that I can put the key when it gets fixed or do I have to learn a whole new method??

[ceelo]

I guess I cant spell either what I meant to say is.....is there an update coming for the nagra master so were I will be able to enter the key 1...or should I learn this romcode, tier thing??