Help Glitching

[kaoticfx]

I am struggling with unlocking cards and am hoping someone can give me an idea of what I may be doing wrong.
I have an orange and a blue nexus (cloned i presume)that I have been testing with. The script I run is either the "new" or Reb's Omniunlocker. I put the pot all the way down until I get a cmd error then tune it up just a bit. Enough to get some type of response and nothing happens. Well nothing besides looping. I have looped 2 yellows and 2 Icams. Rev's 103, 105 and 283. I have 1 283 left that I am not doing anything with until I can get some clarification on. The let the scripts run intermittently for 10 minutes. I then stop and restart. I let 1 run for 6 hours and when i came back it was looped.
The Icams I have glitched on board using the Dummy card and have also pulled one off and placed on a Red Devil with the same results.

On both the orange and blue nexus i have tried using switch 2 and 5 down aswell as only 4. Any advice would be greatly appreciated.
any opinions on a Powersync?

[traylehr]

Stop for right now, & recheck everything !

[davidghoser]

Be quantitative. Are you using a multimeter to measure the resistance? If not, get one and do so. Then at least we can compare numbers.

[kaoticfx]

Stop for right now, & recheck everything !

In regards to the yellows I have stopped...ran out of them :(

the Icams I have one on board that I have left (last one :eek: )

I have gone thru and triple checked all my connections and made sure all the trace cuts were clean and complete. Went as far as lifting parts of the trace to ensure no connectivity. It seems I get a good response regardless what script I use but then it turns to:

-----------------------------------------------------------


I am at wits end on this :(

[kaoticfx]

Be quantitative. Are you using a multimeter to measure the resistance? If not, get one and do so. Then at least we can compare numbers.


on the Rev 103 and 283 I turned the pot down until I got the Bad CMD04 error. Then turned it up. Currently the Ohm reading is about 90ohms(Meter is set to read 200k ohm) I get the following at this setting:

OmniUnlocker
----RST##----RST##--------RST##----------RST##------RST##
RST##RST##RST##RST##RST##RST##RST##-----RST##---RST##

New.xvb
----+--+--+--+---+-NORSP+----+---+---+---+---+NORSP+---+--+----+--NORSP++---+----++++--+-+-+-+---++--+-+-NORSP+

[traylehr]

The loaders you have - did you purchess them from dsshouse or dooda ? also only use one sw. on at a time , the old 102 script ND13 auto vcc seems to do well, ck the settings - set vcc at 02 & 14 , set delay to 330 & 339 (can be diff. if don't work after 5-10min. change , i like to keep them within 5 or so number range so it hits quicker when found) , set glitch max/min 6 & 9 . than 1/2 way down script theres another setting for vcc ( reset to 14 - theres two places). Now the orange loader has the 4053's right? use this one - for rev's 103 - 105 & 281 - 283 , the blue has 4619 yes ? this is for the higher rev's.

[traylehr]

Koatfic has what you need in the way of responses you need to have - if you are only getting ------- something isn't good . People have said a lot of bad things about the clone loaders expecially from dssdooda/house . Your pot settings need to be low (you have it right by turning it down than back a hair but you need the
---+++--nores--+++-noresp--+--++ & so on. This is where your going to finely get some where. But if you have those bad loaders you may end up replaceing them or at least remodding them.

[traylehr]

The edit won't let me edit so - you need the -+-+-+ so try to work with the scripts that give you the responses .

[traylehr]

You may have a bad pot - where you say you get good respns. than it goes to nothing (--------) that could be & most likely is a bad pot . How are you with soidering ? can you replace it ? Any ways the settings i gave you are good to start with - you shouldn't need to have your vcc over 14, most cards/i cams pop at 09 - 13 or so. I also noticed i-cams like the settings for the old rom #3 in the script or the loader2 setting instead of unlooper ( this is what i use)

[kaoticfx]

The loaders you have - did you purchess them from dsshouse or dooda ? also only use one sw. on at a time , the old 102 script ND13 auto vcc seems to do well, ck the settings - set vcc at 02 & 14 , set delay to 330 & 339 (can be diff. if don't work after 5-10min. change , i like to keep them within 5 or so number range so it hits quicker when found) , set glitch max/min 6 & 9 . than 1/2 way down script theres another setting for vcc ( reset to 14 - theres two places). Now the orange loader has the 4053's right? use this one - for rev's 103 - 105 & 281 - 283 , the blue has 4619 yes ? this is for the higher rev's.


Yes I got both from Dooda.

Yes they are both different Chip sets

This is awesome advice. Will try it and respond here with results. Thanks!!

[traylehr]

A lot of what i've read says dooda's / dsshouse's nex. loaders arn't very good , but i've come across a couple that say there's is o.k. so hopefully you got one that's good ! If not you may have to redo the mod . via: finding a mod that is like your loader & following it's inst. to get yours working . Were you useing the blue loader with the cards you looped ? the 4619's (from what i've been told ) have a lot of innerfearence in them , kind of like stadtic in a radio & the lower rev cards don't like it thus -- loop.

[kaoticfx]

A lot of what i've read says dooda's / dsshouse's nex. loaders arn't very good , but i've come across a couple that say there's is o.k. so hopefully you got one that's good ! If not you may have to redo the mod . via: finding a mod that is like your loader & following it's inst. to get yours working . Were you useing the blue loader with the cards you looped ? the 4619's (from what i've been told ) have a lot of innerfearence in them , kind of like stadtic in a radio & the lower rev cards don't like it thus -- loop.


Mik Vortex = 2 looped yellows 1 looped Icam onboard
Nexus Blue (clone)= 1 looped Icam on RedDevil 1 looped Icam onboard
Orange nexus= Can't get a good response
Mik N2= Can't get a good response

I am wondering if I should go ahead and order a Powersync.. Or are there any unlockers you would recommend?

[traylehr]

Stick W/ the orng. nex. & try to get a good read w/it , also if you have to change the pot . You have a few loaders & should be able to get one working . but like i said stick w/ the loader with the 4053 chips until you familuarise yourself w/ unlocking !