c0d3sP4c3 - ROM 102 Blocker v12.0i

[Chrisjacob]

Just wondering if c0d3sP4c3 - ROM 102 Blocker v12.0i is auto roll and if it is how do you disable it. Read that removing the B1 line in
965A:06B1A606CC9569000 to 965A:06A606CC9569000 will disable it. And do you advise on trying this blocker or just pulling card for now

[Chrisjacob]

is anybody up and running on this blocker

[jskey]

I was,,,,just pulled my cam. Dont want to risk it,,,,but codespace with autoroll disabled did survive

[speedball]

running c0d3sP4c3 blocker v12.0p on 4 receivers. Would not have known about the ECM if I didn't see it being discussed on the different sites. All 4 systems still running without any problems.

[crazycat]

I am still up and good with two receivers as well. Anyone else?

[CYCO]

running c0d3sP4c3 blocker v12.0p on 4 receivers. Would not have known about the ECM if I didn't see it being discussed on the different sites. All 4 systems still running without any problems.


Did you do anything to the blocker? or running it as it was downloaded? Do i need to change anything on the blocker?? Thanks

[JT]

I just took the codespace v12p and took out the B1 at address 965B and feel pretty safe about it. Course, it won't autoroll. That way I could take an older image I had complete with tiers, make the minor change and go. The codespace backdoor utility makes manual key updates as easy as it can be. Sure wish I wouldn't have switched to Penga.....but that's the way it goes sometimes in this hobby. Hindsight is always 20/20.

Same thery applies to the v12i, but I'm not 100% sure where the B1 EMM is stored on that blocker.

[JT]

I wouldn't trust any blocker that allows the B1 EMM even in part....at least not for the rest of the week.

[CYCO]

I just took the codespace v12p and took out the B1 at address 965B and feel pretty safe about it. Course, it won't autoroll. That way I could take an older image I had complete with tiers, make the minor change and go. The codespace backdoor utility makes manual key updates as easy as it can be. Sure wish I wouldn't have switched to Penga.....but that's the way it goes sometimes in this hobby. Hindsight is always 20/20.

Same thery applies to the v12i, but I'm not 100% sure where the B1 EMM is stored on that blocker.


Do i just zero these out at=965A=06B1A606CC9569000000000000000000

i could nt find 965B unless this is it

[JT]

Do i just zero these out at=965A=06B1A606CC9569000000000000000000
i could nt find 965B unless this is it

Zero out the red B1 and you should be fine. Also double check address 3067 is 00 and not 08. And that you have 00 at addresses 980D and 988B.

Again, the same principle applies with the v12i blocker, but the address is probably slightly different is all....and I'm not 100% what those addy's are.

[john smith]

Zero out the red B1 and you should be fine. Also double check address 3067 is 00 and not 08. And that you have 00 at addresses 980D and 988B.
Again, the same principle applies with the v12i blocker, but the address is probably slightly different is all....and I'm not 100% what those addy's are.


My rom is mark at 3067 can I use this blocker are Im out of luck.
Thank You

[JT]

I think your SOL. The EMM won't get you, but as soon as the ECM comes down and checks for the 08 at addy 3067, BAM!, your looped and dead forever. Don't use that rom. There have been patches that mask marked roms in the past. This will be the first need for it with a rom102, but it worked great with rom10's in the past. Someone might come out with a patch for marked 102's at some point. Your down with that rom, but maybe not out forever. Shelve it and hope for the best.

[john smith]

Thanks

[speedball]

I'm running the blocker as-is. Didn't modify any lines except changed the password. Still running as of noon today

[pirisatu]

My CAM has a 03 (NOT 08) at 3067...Is it safe to use for now?
Thanks

[JT]

My CAM has a 03 (NOT 08) at 3067...Is it safe to use for now?
Thanks

NO! Anything other than 00 @ 3067 will result in a loop.

[singh60]

Is the mark checked at row 3060 and the column 7?

[jamrock1]

Is the mark checked at row 3060 and the column 7?
yup

[jamrock1]

also remember to disable autoroll on cod3sp4c3 blocker
964A=42A48300000000000000000000000000
change to
964A=00000000000000000000000000000000 to disable.