Problems with 510 DVR and Enigma Card

[cptmorgan2000]

I changed my ird and box keys on my tsop and loaded the rom, and eeprom files that came with software 3.4. When i insert my enigma card in my 510 dvr i get error messege smart card is not valid for this receiver. What am I doing wrong ..
Any help would be appreciated...

Thanks

[mopar611]

I dont know nothing about how the enigma card works..

But the 510 uses SKs.. You have to either delete them, or make them
match the image on the card..

Since I dont know how the card works, I dont know which way to take
you for advice..

Does the image you are using have a DT08?? Or does it use SKs?? You
need to figure that out..

If you change the info on the receiver to match whatever image you have
on your card, you need to remarry the harddrive to match your numbers
on the card..

So depending on what you are doing, will dictate how you will approach
this...

Mopar

[cptmorgan2000]

This was the approach i was taking....
I used jkey 5900 since i found out it was most compatible with 510 dvr.
I opened it choose the correct ird model 510-5900 and hit detect and got my original box keys and ird # ... I choose flash programming and choose the correct ird model (510-5900) and choose Flash I... I then went ahead and chose FULL under chip/sector programming and read both Flash I and Flash II
After I did this I modified both files using flashedit-2.1beta9-bin to reflect the following changes...

IRD #: 011C746C
Boxkeys: 8CA6A88CFDE2E263

I edited both Flash 1 and Flash II bins and then saved them... I went back into jkeys and erased Flash I and Flash II three times then went ahead and programed both Flash I and II. When I erased both sectors i did go back to the main screen and hit detect when i choose 510 for the receiver and it did give me FFFFFF for both the IRD # and Box keys... So I know i erased both of them properly... know what problem I am running into is after i reprogrammed Flash I & II I went back to main screen in jkeys... choose 510-5900 for ird and it returned me the original box keys and ird # .. I dont know y this happened... For some reason when I choose 501-5100 for the ird model it gives me the new modified box keys above and IRD #... I also made sure when I went to Flash programming in jkeys, i had IRD MODEL 510-5900 selected...

what could possible be the problem... I changed my TSOP and EEPROM lock switch to unlock mode... so i know its can't be that.... b/c when i erased Flash I & II it gave me FFFFFF for box keys and IRD #...

Does anyone have a DVR 510 and have been successful using the ENIGMA CARD.....
I used the Default EEPROM_Dish.bn102 under Enigma 3.4 to program EEPROM programming under jkeys...
So are u telling me know that I have messed around with my TSOP I have to remarry the Hard Drive back to the receiver... Y would I have to do that if I never changed the Hard Drive... Any HELP would be appreciated....
When I programmed the enigma card I used the Default Load ROM and Load EEPROM files that came with Enigma 3.4 .... what do I do to solve this problem....

Thanks

Cpt

[cptmorgan2000]

Does the image you are using have a DT08?? Or does it use SKs?? You
need to figure that out..

Mopar


How do I figure out if the image I am using has DT08 or uses Sks...

Thanks for the help...

Cpt

[skinerd]

A 510 will use SK's and they must be removed for the enigma to work. I suggest the Sks be removed and the receiver data be moved so the receiver appears to be a 508 with "moved bootstrap" type flash. Using this method, a 510 will definately work with enigma.

[robm661]

i have a 501 and the same thing happened to mine, i had to rezip the enigma after i rebooted my cpu ,i shut down my spyware and reloaded the rom the epprom then pput the new keys then i programmed the card then had to do a check signal on the ird twice and wait on channel 202 then it came in about 90min the first time then after that when the keys change i use program card with new keys dont reload bin or epprom,then it will come on after check signal on ird

[cptmorgan2000]

A 510 will use SK's and they must be removed for the enigma to work. I suggest the Sks be removed and the receiver data be moved so the receiver appears to be a 508 with "moved bootstrap" type flash. Using this method, a 510 will definately work with enigma.

Hey skinerd (http://www.dssftp.com/forum/member.php?u=1911) Have u done this before.... How do I remove SK's from my 510.
What do I use move the receiver data so that it appears to be a 508 with "moved bootstrap" Have you successfully accomplished this... Can you please help me out with this... I am sure there other 510 owners who are in the dark besides me ....
Did you have to remarry your hard drive to the receiver if you messed around with the TSOP..
Thanks
Cpt

vbmenu_register("postmenu_425335", true);

[cptmorgan2000]

i have a 501 and the same thing happened to mine, i had to rezip the enigma after i rebooted my cpu ,i shut down my spyware and reloaded the rom the epprom then pput the new keys then i programmed the card then had to do a check signal on the ird twice and wait on channel 202 then it came in about 90min the first time then after that when the keys change i use program card with new keys dont reload bin or epprom,then it will come on after check signal on ird


What do u mean by you had to rezip the enigmas after you rebooted your cpu.. You lost me on this.... Did you do all this after successfully changing the IRD # and box keys to the ones Enigma people recommended ....
(Changed to the public keys)

Thanks

Cpt

[robm661]

i changed my ird to the ones they provided ,then i jtagged it to make sure it was right it was, then i already had downloaded 3.4 i followed the instruction bin first then epprom ,then i put the new keys in ,then i programmed the enigma and before i did this i shut off all spyware antivious software then i put the card in after 501 was left alone after modifing the tsop with just the satilite feed takes about 15min to reprogram ,this is how i did the second time and no problems ,oh i downloaded the enigma 3.4 without the antivirious software and spyware on and then it said005 wrong card the first then i did a check switch with the new keys off and running,sorry if u dont understand how i did it ,i suck at giving instuctions

[robm661]

oh ya forget auto roll its quiker just to put the keys manually and just program it ,not bin and epromm only did that once after i was up and running,ialso used j-keys 301-5900 if u modified your ird and jtagged it again and have the proper numbers its your programming of the enigma really sensitive,mopar611 helped me this is the thread http://www.dssftp.com/forum/showthread.php?t=69268 only thing i did different was to erase sa52

[cptmorgan2000]

So your telling me that since you had spyware & antivirus running, it gave you the error Card is not authorized for this receiver?????

[robm661]

as soon as i shut that down unziped the file again put the bin in then eppromm then put keys in then programmed i was good,then when the keys change i just put the new keys and hit program thats all ,good luck

[cptmorgan2000]

Does any1 know how to remove Sks from my image so I can get Enigma to work with my receiver...

Thanks

Cpt

[skinerd]

In a hex editor, FF out lines 003FFF40 through 003FFF90.

Make line 003FFFC0 01 1C 74 6C 8C A6 A8 8C FD E2 E2 63 91 FB FF FF

That removes SKs and sets receiver number and box keys to enigma (public) numbers.

Flash will then be a "moved bootstrap" type flash............. works......

[cptmorgan2000]

In a hex editor, FF out lines 003FFF40 through 003FFF90.

Make line 003FFFC0 01 1C 74 6C 8C A6 A8 8C FD E2 E2 63 91 FB FF FF

That removes SKs and sets receiver number and box keys to enigma (public) numbers.

Flash will then be a "moved bootstrap" type flash............. works......


So I would have to open my TSOP image that I saved using Jkeys...
and make the appropriate changes and save it back to receiver...
After you did this... were u able to open jkeys, choose IRD # 510-5900
and did the IRD # and box keys reflect the changes that you made using the hex editor???

Thanks for the info ....

Cpt

[robm661]

u are using the advanced setting in flash edit ,put the numbers from enigma in there in hex ,then save write it back to flash 2 then pad1 grounded dissconnect plug ird in for 1 min then go back to jkeys erase sector sa52 then plug ird into satilite feed like reprogram ird then put your enigma card in with latest keys should go right on,make sure pad 1 is grounded when writing back to ird

[skinerd]

So I would have to open my TSOP image that I saved using Jkeys...
and make the appropriate changes and save it back to receiver...
After you did this... were u able to open jkeys, choose IRD # 510-5900
and did the IRD # and box keys reflect the changes that you made using the hex editor???

Thanks for the info ....

Cpt

After these changes, jkeys usually detects the receiver as a 501/508 moved bootstrap. ( depending on which jkeys version). And will show the new numbers.

FF'ing out the lines I said above, removes the SKs and the old receiver numbers.
The change to the 003FFFC0 line is the new numbers. Receiver number, boxkeys and CRC.

[cptmorgan2000]

After these changes, jkeys usually detects the receiver as a 501/508 moved bootstrap. ( depending on which jkeys version). And will show the new numbers.

FF'ing out the lines I said above, removes the SKs and the old receiver numbers.
The change to the 003FFFC0 line is the new numbers. Receiver number, boxkeys and CRC.

I just need a little clarification... Sorry for this..
ok I saved my TSOP image using Jkeys to file
510-5900 - Flash 2(U7-29DL323) - Full.bin
Do I open this file in hex editor... I downloaded Hex Editor XVI32
You mention before I need to FF out lines 003FFF40 through 003FFF90. and Make line 003FFFC0 01 1C 74 6C 8C A6 A8 8C FD E2 E2 63 91 FB FF FF ... Do I do all this in the hex editor... Which hex editor do you recommend I use ????

Thanks again

Cpt

[cptmorgan2000]

ok this is what i found in my hex editor.... I didn't find lines
003FFF40 through 003FFF90

What I found was lines 003FFF48, 003FFF98... I attached a screen shot of what my hex editor displayed for me.... So do I FF out lines
003FFF48, 003FFF70.. I am not changing any info in line 003FFF98.
As you can see line 003FFFCO already has 01 1C 74 6C 8C A6 A8 8C FD E2 E2 63 91 FB FF FF.. So should I save this file as
510-5900 - Flash 2(U7-29DL323) - Full.bin and then program it to my TSOP using Jkeys. I will save it under Flash 2. IRD # 510-5900.
You also mentioned I need to Erase SA54...

Thanks

Cpt

[skinerd]

I use winhex, and those are the line numbers it displays.
I never erase SA54.

[notsonewbie]

if you load your tsop with a 508 public file as skinerd said that would be alot eisier. let me know if you need istructions. you need to match your board configuration so your dvr recorder will work. i have a bin for dcea,z,and others. you can find it in the files section also in mili's file shop. skinerd knows what he is doing he got me sqared away with my 510. all you do is erase both flashes and rpogram flash 7 and the new eprom and let it stream and update. then you can run your enigma as it will think it is a 508 without sk#'s don't follow my isntructions this was wrote in haste. any good tsop file will come with instructions.

[cptmorgan2000]

if you load your tsop with a 508 public file as skinerd said that would be alot eisier. let me know if you need istructions. you need to match your board configuration so your dvr recorder will work. i have a bin for dcea,z,and others. you can find it in the files section also in mili's file shop. skinerd knows what he is doing he got me sqared away with my 510. all you do is erase both flashes and rpogram flash 7 and the new eprom and let it stream and update. then you can run your enigma as it will think it is a 508 without sk#'s don't follow my isntructions this was wrote in haste. any good tsop file will come with instructions.


Hey can u send me instructions ... Send me any files that you used to get your DVR510 working.. email address is asthanas2@hotmail.com put in subject DVR510 files!!!! Thanks alot... if you have any files u used to get your dvr working with the enigma card please send them my way... Much appreciate all the help

Thanks alot guys !!!!

Cpt

[notsonewbie]

need this to know what files will work with your hard drive.

it is a little whit sticker twards the front of the unit

have you done your vid mod yet?

check that out first, it is not easy to do, it is easy to ruin your ird though

[cptmorgan2000]

need this to know what files will work with your hard drive.

it is a little whit sticker twards the front of the unit

have you done your vid mod yet?

check that out first, it is not easy to do, it is easy to ruin your ird though

The 4 letter code is DFHD..... I have done my vid-mod.. I actually sent out my receiver over a year ago to a company to get my TSOP & EEPROM locks installed, along with a Jtag and Vid-mod ... so I am take care on that end .. I just need to know which files to use for my enigma card to work w/ my receiver.. Does those 4 letters give you any lead way????

Thanks again for all your help

Cpt

[skinerd]

I send some DFEA(D) files, they work in any DFxx box......use as is and you'll be fine.
they are virgin so will marry hard drive.

[cptmorgan2000]

I send some DFEA(D) files, they work in any DFxx box......use as is and you'll be fine.
they are virgin so will marry hard drive.


The file R0018642028-PVR501-23AB-DFEA-10S-P080-U7 that was sent to me .. ended up changing the menus to French ... Does any1 have the english version of this ...

Thanks

Cpt

[skinerd]

The file R0018642028-PVR501-23AB-DFEA-10S-P080-U7 that was sent to me .. ended up changing the menus to French ... Does any1 have the english version of this ...

Thanks

Cpt

Change back to English in system setup.....

[notsonewbie]

sorry i know it is not funny for you.
i looked all over in mine in english and i can't find where to change it
is it working though?

[cptmorgan2000]

sorry i know it is not funny for you.
i looked all over in mine in english and i can't find where to change it
is it working though?


Worst thing is not only does it not work.. but the menus dont all load up in french.. otherwise i would have figured out a way to change it by now ...

Cpt

[skinerd]

Worst thing is not only does it not work.. but the menus dont all load up in french.. otherwise i would have figured out a way to change it by now ...

Cpt

I'll send another.....

[skinerd]

DFJA(D) file set sent, try and let me know.....wierd, cause the DFEA files sent have been use by me several times w/o problem.

[cptmorgan2000]

Should I just be erasing Flash I & II and reprogramming only falsh II with the file u sent me ... the ROM and EEPROM files I use that came with enigma card????

Thanks

Cpt

[skinerd]

An update on 510 DFEA boxes. Today I loaded a DFJA tsop at P080 (DFJD virgin eeprom) into a DFEA(D) box, used it to marry 2 different harddrives, worked fine, then stream updated to P365, no problems at all.

[gcan]

i sent a working DFHD P080 to you Cptmorgan, btw, why didnt you FF out your Sk's in flashedit? anyways, the file i sent have them FF'ed out already so change the 00's to your personal info and you can take it from there, pm me if you get into any problems.......................................... ..gcan