Problem with Attention 015

[cptmorgan2000]

I can't seem to get past Attention 015... Acquiring satellite signal ...Please wait.. Doesn't even give me 1 of 5 and so forth.... I successfully programmed my receiver w/ the new TSOP (new changes applied for Box keys and IRD #)
Then used my own EEPROM when programming Enigma card.. didn't get anywhere that way so i went back to the defauly EEPROM that was supplied...
Any idea how I can fix this problem ...

Thanks

Cpt ...

Testing on a DVR-510... used both Enigma 3.4 and 3.6 and no luck so far... Any suggestions???

[coolgrin]

try to check the info screen. see if it sees the card.See if it sees a rom102 rev10b.If it does then wait it out my 3100 sometimes takes 20 min to half an hour.I walk away when I come back its working.Timing issues are bad with some ird's.Try it anyway as long as ird recognizes card there it should go.Sorry I coulden't get back to you been a long weekend.

[cptmorgan2000]

This is what my receiver says ...Dish 500 Card Ready DNASP102Reb10B

So i guess the receiver detects the card... I have been stuck on that Attention screen for hours... Rebooted machine many times still same thing...

Are others having this problem or is it just me???

Thanks

Cpt

[norton]

try a check switch and see if that helps.

[cptmorgan2000]

Did this mulitiple times and still nothing ...

Any other suggestions???


Cpt

[cptmorgan2000]

Did this mulitiple times and still nothing ...

Any other suggestions???


Cpt

[coolgrin]

Exalter is using the same ird as you I would pm him and ask him.He also had a hell of a time at first.I am wishing I had a 510 so I could understand a little better.It all seems right what you have done but if your ird is recognizing your card it should go.If I could give you better support I would but I am at a loss.But hit Exalter up on your issue.Site is up again kinda.

[cptmorgan2000]

Hey thanks for the files Coolgrin... Much appreciate the help you have provided me..

Thanks again

Cpt

[coolgrin]

Glad I could help atleast a little.What are the odds you have a rom 10,102,or atmega?If you do have any of those cards at all you should try them.If you have a rom 10 use any old bin with updated keys.Just to make 100% sure ird is ok.I feel it is but would answer all questions on wether or not it is timing problems with the enigmacard or not.Also when programming card try picking the 301-013 ird when you program your card instead of propper one you are using.I am not sure if it will make a difference or not but my 3100-010 took better using it instead of using propper one.Worth a shot seeing the release of 3.6 is unknown.I am hoping scherbius is going to keep his work and spend some time at enigma site.He stated last week he would start to spend some time on mondays there.
I see by your post times you are loosing sleep over this damn card.Thats why I like the easy ird's makes my life just a little simpler.lol Plus I am too cheap

[coolgrin]

Oh ya I also remember Exalter saying he had to put card in ird then unplug ird for a few minutes before he could get his to work for him.That could be worth a shot too if you haven't tried that yet too.

[coolgrin]

hxxp://www.enigmacards.com/forum/showthread.php?t=43&highlight=exalter (http://www.enigmacards.com/forum/showthread.php?t=43&highlight=exalter)

here is the thread where exalter explained his problems and what he did to get his going.It is post 2 on that page.Change the hxxp to http

[norton]

is the ird just saying "DNASP102Rev10B" or does it list a cam id as well? I would assume it does, but something to check, if not then i would say the card isnt communicating with the ird properly

[cptmorgan2000]

Oh ya I also remember Exalter saying he had to put card in ird then unplug ird for a few minutes before he could get his to work for him.That could be worth a shot too if you haven't tried that yet too.


No luck ... tried this also!!!!

[cptmorgan2000]

Here is what the system information screen tells me ..

MODEL ID DP510

RECEIVER CA ID R0018642028-33

SMART CARD ID S000000000-00

DISH CARD READY DNASP102Rev10B

SOFTWARE VERSION P080DFED-N

BOOT STRAP 23ABDFED

REMOTE ADDRESS 1

LOCATION ID 673A9CBC

[Eldune]

you have no cam ID . check your connections and reprogram. MAKE sure your ird TSOP is up to date.!!!

[cptmorgan2000]

Are u refering to the SMART CARD ID... I am supposed to have a CAM ID one after reprogramming the TSOP and and the enigma card... Can you please elaborate on what your talking about ..

Thanks


Cpt