3.5 problems

[V_2]

Thank you Bishop for the update. I cant wait for the new forum

[hacker]

I can't get it to roll but I just programmed with the new keys and will post back.

[V_2]

Time zone still off and it would jump between 019 or 005 with keys entered. I had it on channel 101 and it would flash 019 for about a second and be ok for a minute or so PVR 508 with latest software public info

[hacker]

Ya i'm getting that too. I re programmed it again with the keys and it was on 2 of 5 for about 10 minutes and now flashed the 019 error and it's back on 0 of 5

[hacker]

I am using a 501 converted to a 510 with public info and software is up to date.

[sunmachine]

The BEV EPROM loads with an error.

[V_2]

Something is up with 3.5 software it will hang or freeze while writing the eeprom. I first used my own tiers to check time zone and saw no change then went to use the suppled bin and now all I get is eeprom update failure. but when I run the diagnostics test on the card everything checks ok

[hacker]

Same with me I just tried the supplied bin and got an error updating eeprom! WTF is going on? I'm going to bed will mess around with this tomorrow goodnight

[arms]

Does this mean the price of the Rom 102/103 is going to go through the roof again.:D Arms

[michael007]

I got it working for Dish! What I did was ERASE the four "ecm keys - private", programmed the supplied rom, programmed the suppled EEPROM (I got the lag as well) then program card. I put the card in my 510 and it worked on the first try, been working for an hour now.

If your using the card for DISH make sure you erase the four "ecm keys - private" because they are used for BELL i guess.

[tomeczek]

Guys,
Could you move this discussion to EnigmaCard forum?
It's been up today!

[DB]

I have a question. This is right from the read me.

EnigmaEdit3.5
-added private key support
-added Maps 4E, 4D, 55, 56, 57, 58 (ECC / projective coordinates)
-New maps are fully coded but not active. Will be enabled in EnigmaEdit 3.6.

It looks like map57 was coded, but why on earth would Scherbius code it and not make it active yet? Why wait. I am sure the BEV users would like it now.

[sunmachine]

BEV users would definately like MAP57 to be working NOW.

Where can we get the Private BEV IDEA Keys from? I haven't found a program or site that lists them or keeps them upto date.

[wilmero]

So basically... this doesn't work? I'm just asking before I fry my card with this stuff...is ANYTHING fixed?

Update: Nevermind, this release really sucks. I keep getting to the point where it says "closing usb" then it says writing to EEPROM failed. End of story.... I tried the supplied bin and my own bin.

Does yours work mili?

[DeathStar119]

D*SH -
Is 3.5 suppose to autoroll? Cause I've programmed my card twice with 3.5, waited 20 minutes each time, and yet still nothing.

DS119

[wilmero]

D*SH -
Is 3.5 suppose to autoroll? Cause I've programmed my card twice with 3.5, waited 20 minutes each time, and yet still nothing.

DS119


I don't think so, I think that feature is coming out in 3.6 or 3.7....4.0 :p

*************
RELEASE NOTES
*************

Currently working on adding all ST opcodes to support full autoroll for version 3.6.



EnigmaEdit3.5
-added private key support
-added Maps 4E, 4D, 55, 56, 57, 58 (ECC / projective coordinates)
-New maps are fully coded but not active. Will be enabled in EnigmaEdit 3.6.

[Twostep]

Working, finally, but not glitch-free.

STILL will not load private tiers and timezone. And will NOT accept key changes, unless you change them in the bin first before writing EEPROM.

As for the EEPROM write failure, you may get this, I did....just keep writing it. It'll go on there.

Anyway, it's up and running perfectly, for now, in a 301013 IRD, with no freezing - but still no locals and eastern timezone only. The next test will be the first time the keys roll.

[CrownRoyal]

i cant get passed the 005 nag, any ideas?????

thanks

[DB]

i cant get passed the 005 nag, any ideas?????

thanksYou put the right keys in. From what I have read the auto roll isn't working.

[James-x]

i am having same shit 019 005 and eeprom frizzing till the point that program will not respond great........... we need 3.6 like NOW

[qrb123]

I see the the enigma has been very consistent with it's level of quality.

[CrownRoyal]

You put the right keys in. From what I have read the auto roll isn't working.

Welll i THINK i have, i hav etried adding them many differnt ways, i am used to the rom days when you could do it from scripts.

I changed them via the enigma program, and changing them with nagra 5.2 and opening the bin. running a little patch:
; Idea Key 86:
$A95A=00000000000000000000000000000000
; Idea Key 96:
$A9BA=00000000000000000000000000000000

with what ever current key are, but when i load eprom from enigma, it goes back to default

am i soing somehting wrong? any helps i thank in adv

[hacker]

You have to put a space after every 2 numbers. Try doing it again after you load the eeprom then program. Here are the keys

key 0: 50 57 D2 64 CC 4B 8B 15 22 15 E4 65 07 5E 2C 66
Key 1: D5 15 77 7C 12 9D 81 06 58 59 46 33 FE 2D 7D C6

[fasteddie66]

redo the card with 3.5 and the problem I am having is when at 015 acquiring sat signal it takes forever to get past progress 2 of 5 or its seems to freeze there or at 3 of 5 keep reinserting the card
could someone give me some advice the kids are bugging me
301.01
on dish

[Twostep]

.

with what ever current key are, but when i load eprom from enigma, it goes back to default



First, be aware we just had a key roll, so make sure you get the latest ones just posted. Then, take a private bin (not Enigma's) and edit the keys with DTTierworks, etc. When you 'load eeprom' with the Enigma program, select your edited private bin. It will work; I just got through doing it with the new keys.

[fasteddie66]

is it possible to get steps by steps , don't want go wrong direction


First, be aware we just had a key roll, so make sure you get the latest ones just posted. Then, take a private bin (not Enigma's) and edit the keys with DTTierworks, etc. When you 'load eeprom' with the Enigma program, select your edited private bin. It will work; I just got through doing it with the new keys.

[CrownRoyal]

yes a step by step would be great, i have done everything to the T in instructions, and all i can get is a black screen even with th enew keys!!! i do know what i am doing for the most part

thanks

[hacker]

1. test card
2. load rom
3. load eeprom
4. enter these keys:
50 57 D2 64 CC 4B 8B 15 22 15 E4 65 07 5E 2C 66
E5 59 F8 E6 85 2C E0 C3 45 6B 1E CF 99 7F 20 81
5. clear the private keys those are only for bev
6. program card

[hacker]

If you still have problems switch back to 3.4. I am using 3.4 because I found less problems with it.

[cptmorgan2000]

I can't seem to get past Attention 015... Acquiring satellite signal ...Please wait.. Doesn't even give me 1 of 5 and so forth.... I successfully programmed my receiver w/ the new TSOP (new changes applied for Box keys and IRD #)
Then used my own EEPROM when programming Enigma card.. didn't get anywhere that way so i went back to the defauly EEPROM that was supplied...
Any idea how I can fix this problem ...

Thanks

Cpt ...

Testing on a DVR-510...

[hacker]

Try 3.4

[coolgrin]

Look for a program called keyupdate v8 this handy little will let you update keys on any 102 bin.Every time the keys change I updaye keys in supplied bin in enigma edit using this program works awesome.Not sure if program is here or not but I use it to update all my 102's will also do atmega's 103's cemu both providers great little program

[tomeczek]

Look for a program called keyupdate v8 this handy little will let you update keys on any 102 bin.Every time the keys change I updaye keys in supplied bin in enigma edit using this program works awesome.Not sure if program is here or not but I use it to update all my 102's will also do atmega's 103's cemu both providers great little program
Every time I read your posts, a little grin appears on my face. :)

Found "keyupdate" here: http://thefileshop.com/showthread.php?t=2493&highlight=keyupdate

(See you at EnigmaCards! The Apache/Fedora server is up. Hopefully the forum will be back soon!)

[Ohms]

All I get is "eeprom update failure" whenever loading any eeprom including the one that came with it.

[SMG4me]

Guys if you're using your favorite app like NagraEdit or N2Edit to patch the current keys to included public bin be aware that the keys are in a different location than you are used to. Here's the location for the public EEPROM_Dish.bn102 bin:

;)

; Idea Key 86:
$AAD4=5057D264CC4B8B152215E465075E2C66
; Idea Key 96:
$ACB6=E559F8E6852CE0C3456B1ECF997F2081

[CrownRoyal]

Well i have done EVERYTHING right , and all i get is a black screen, previews come in fine, i dont get the 05 screen, just black

any ideas? or just wait for new sofwtare again?

[hacker]

Did you try using version 3.4?

[soter]

All I get is nothing more then 019 ERROR on my two Enigmas from day one that I received them, over a month and a half ago...I have used every version there is, including the great 3.5!

[Twostep]

Here is my step-by-step, if you'd care to try it. It's running well in a DN 510 (except autoroll)

I use a public-number, NoRSA, ROM 103 bin and have the receiver flashed to match. It's a complete bin, with tiers, timezone information, etc...but does NOT have a blocker patched. You don't need a blocker with the Enigma card. Don't use a 10B bin; use a 103 bin.

I took my bin, loaded it in DT Tierworks, clicked the key icon and pasted the current keys in the appropriate boxes. Then I clicked 'save and write keys'. Then, clicked 'modify bin file' and closed that program.

Then I opened Enigma 3.5, loaded the ROM again, then loaded the eeprom I just modified with the current keys. After writing the eeprom you'll most likely see a delay (30 sec or so) in closing the USB. If you get an 'update failure' nag, just rewrite; it should go on eventually.

Program card and put it in the IRD.

Here's what may be happening with some of you: If you paste the current keys in the provided boxes, the program will ignore them and write the default keys, which are wrong. You MUST edit the keys in the bin itself before writing it. As soon as the eeprom write begins, the proper keys will display in the boxes. Again, putting them in there yourself is fruitless. Put them in the bin FIRST. If the program loads the wrong keys, you'll see step 2 of 5 hangups, 'not authorized' and 'not inserted correctly' nags, guaranteed. You HAVE to load the current keys.

Note: On advice from another member, I erased all the ECM Private Keys data before programming. Just highlight and delete. Also, you're still not going to see your private tiers and timezone, even though they're in your bin that you modded with the current keys. The keys will load; the tiers/timezone won't. How strange.

[bill]

All I get is nothing more then 019 ERROR on my two Enigmas from day one that I received them, over a month and a half ago...I have used every version there is, including the great 3.5!

Maybe you are not giving it time to load before clicking on program card. When you load rom, let it tell you when the load is complete. Same with eeprom. Then hit program card. Just a thought.

[soter]

Maybe you are not giving it time to load before clicking on program card. When you load rom, let it tell you when the load is complete. Same with eeprom. Then hit program card. Just a thought.

That's one of the reason why I'm frustrated with these Enigmas. It does say it is complete then I select program card and it sends the information successfully. I have different recievers consisting of 3100.010's and HD6000 and they are all a no go with 019 errors on public and private bins.

[SMG4me]

Just fyi from my stuff I was able to get it working on both public and private. Just no keys rolling as everyone has noted. My private is a 6000 on D*sh and it does work. I can offer what I did for the private No RSA mod:

1. Get your bin. This is a Rom 102 Rev 103 bin with your private info, 0D and DT08 or SK. Essentailly a working bin.

2. Clean the codespace on the bin. Then use Mr TierWorks to clean off the channel and PPV tiers. Don't add any new tiers just yet.

3. Add the 2 EnigmaEdit key locations to the bin. I suspect this is where some are getting caught. As I mentioned in a previous post the keys are in a different location. On your private bin you might have to add them. Use NagraEdit or N2Edit to add the keys via the patch below:

!ADD 06 1A 138000000100000608105057D264CC4B8B152215E465075E2C 66
!ADD 06 1A 13D9A316010000460810E559F8E6852CE0C3456B1ECF997F20 81

With the addition now EnigmaEdit can find the key locations. To change them you can change them either in EnigmaEdit or create a patch. If you want to create a key patch it will be unique for your private bin as the location address will vary. Look for the location of the keys under NagraEdit - Dataspace tab and adjust the patch accordingly.

3. Once the bin is all patched load it up in Mr TierWorks and create your channel and PPV tiers.

4. Save it and then you're good to go!

5. Open up EnigmaEdit 3.5 and select your receiver from the drop down. Then load the ROM and the EEPROM. After the EEPROM load you will see they keys. You can change them if needed. I also deleted the B*v ecm keys and left those fields blank.

*** If you are getting the error message loading the EEPROM in EnigmaEdit 3.5 I believe I found the problem. It looks like the USB cable has to be short. A short 3' cable direct from the computer works perfect. I initially tried hooking the same 3' cable to USB port on my LCD monitor which connects to the computer by another 6' USB cable. Loading the EEPROM failed every time connecting this way. It has never failed going direct to the computer.

I hope this is of some value. Now we need autoroll and a time zone change option.

;)

[michael007]

Mine just rolled for the first time! :) Maybe there is hope for this card. Running 3.5/510/supplied bin/supplied eeprom

For the people that didn't roll here are the newest keys

Dish Network (Last Update: 2007/02/09 6:34 PM PST)
86: C3 24 65 6A 6B DB 84 CC C0 C0 9B 18 8F 85 C6 F9
96: E5 59 F8 E6 85 2C E0 C3 45 6B 1E CF 99 7F 20 81

Bell ExpressVu (Last Update: 2007/02/09 2:34 PM PST)
86: E4 A3 E0 9F F9 24 EA D0 DF 62 38 80 A1 09 23 C8
96: 88 DD A1 4E 54 55 FC C4 6C AC 78 D2 63 FE A6 44

[fasteddie66]

I Finally Got Its Going & This Is What I Did
Use Nagra Master
Clean Code Space
Put In New Keys
Programe Card
Delete The Private Keys
Bravo And The Kids Are :d Off My Back

[CrownRoyal]

once again i have done verything to the T with the latest keys and all i can get is a black screen, i have tried all suggestions here. i am about to give up and see if anyone wants to buy my card for 1/2 price!!

still open for suggestions

CR

[SMG4me]

CrownRoyal, I assume you're using the EEPROM_Dish.bn102 for D*sh...? If you are patch it with this in NagraEdit or N2Edit:

; Idea Key 86:
$AAD4=C324656A6BDB84CCC0C09B188F85C6F9
; Idea Key 96:
$ACB6=E559F8E6852CE0C3456B1ECF997F2081

Save it and use EnigmaEdit to write it to your Enigma... should do it.

[CrownRoyal]

nope no luck, i think i might have a bad card!!!