Mili's Atmel Programmer and ST19XL

[OverEasy]

Hey fellas is their a ST19XL flash I can use with Mili's Atmel programmer and
FBPRG16 program ?

THANKS OverEasy

[smilingjack]

Mili program for the MaxMel interface for EMU is list in the sticky on top

[OverEasy]

First THANKS for replying SJ

This is a C/P from the sticky: For st19xl I have some good max-mell boards,and an atmel 2313 programer.that i ran with fbprg16.


Jack it doesn't tell which flash to use with the Atmel 2313 programer and fbprg16
program when flashing it for ST19XL and thats what Im asking for. But it does tell
me it can be done this way.

THANKS OverEasy

[JT]

!!SAn2_102_289_2313_2chip flash on the atmel, and I can't remember the image for the aux'd card. If your not going to run an auxed card, just run Cemu. That's what I'm doing these days and why I can't find my st19xl files.

[OverEasy]

THANKS JT

The one you posted is for b3v (289) right ?

I have this flash for XpAtmel will it work for fbprg16 ? If so I know I only need to use one of these but I don't know which one ? I believe its the eeprom.

!!SAn2_102_10B_2313_2chip_ironhead.exe.eeprom.hex

!!SAn2_102_10B_2313_2chip_ironhead.exe.program.hex

[JT]

No, the one I posted is for Charlie (102_rev10b). You'll have to find a BEV flash. Check out the fileshop and look through the emu section until you find a st19xl for BEV. It should all be there somewhere.

[OverEasy]

Sorry JT I should have said I wanted it for Charlie not B3V.

I thought what you posted 102_289 is B3V and what I posted 102_10B is Charlie anyway the flash I posted is for Charlie and its working right now I flashed it with XpAtmel and a loader. My problem is I need to flash some more chips and Mili's Atmel programmer is all I have. Im under the impression that XpAtmel will not work with Mili's Atmel programmer. Will I need to use fbprg16 instead and will the flash I posted above work with Mili's Atmel programmer and fbprg16 if I only use the eeprom ?

[JT]

Oops, brain fart. The 289 I posted IS for BEV. Glad you caught my meaning even if I tried to make it even more confusing than it needs to be. I intended to post the Charlie file name. The flashes you have should work for Chuck IF you were flashing with XPatmel.

Flashes for XPatmel are different than for fbprg16. You will be loading a single .hex file when using fbprg16. The flashes you posted are for XPatmel; you can tell by one file is the eeprom and the other is the program file, and for XPatmel, you need both. You will need to find rev10b hex file for fbprg16 since the files you listed there won't work in fbprg16. Don't know if cancoms 10bar.hex will work with st19xl or not, but I at least can locate that flash. You want to program your aux card with perkysaux-1.22 .bin image.

[t160hq]

You want perkysaux 1.23 for the latest version of st19xl.

t160hq

[JT]

Thanks for clarifying that t160hq. I'm not running st19xl these days so I didn't know there was a new perkysaux image.

[OverEasy]

Ok Im posting my results useing Mili's Atmel programmer or any Simple Atmel programmer and jEEPersDX with the flash below. I was able flash the 2313 for ST19XL for use with Charlie.

!!SAn2_102_10B_2313_2chip_ironhead.exe.program.hex