Success with private info.

[skinerd]

Sometime back I purchased a used 510 receiver with a married card.

Couple days ago I was successful in transferring the private numbers from the 510 flash into 2 different receivers, a 301-013 dual tsop, a 301-013 single tsop. This included SKs. I now have 3 receivers setup for private numbers, all use the same card file, all work 100%.

I did not use GenDT08 or anything else to generate any numbers, I simply transferred the receiver number, boxkeys and Sks from the 510 to the other 2.


A dual tsop -013 is not a SK receiver, but I was able to set it up for them and it works fine.


I tried to use a 301-013 single tsop as a base, did not work in the 510, and I don't know why...

The card was setup by wiping tiers from the bin, and then adding tiers, (a lot of them too) with DT Tierworks. Adding a private blocker, then writing to card.

[aposton]

Yea I don't know the deal with that, but I tried using that GenDT08 when it first came out with no luck.So I redid the TSOP on a 3700 with the #'s from a 510, and cloned the 102 bin on another card,works fine, now I wonder if the only time you would need the GenDT08 proggy is when you have an unmarried card and receiver without the card info.Huh!

[Crazy1_79]

if you have a subbed married rom 102 image for any receiver it contains all data necessary for private numbers using those numbers between married rom and receiver. however if it is a SK receiver it will work for those only. it will not work for dt08 receivers without some modification.

[otsos]

skinerd (http://www.dssftp.com/forum/member.php?u=1911)@

Can you make small step by step tutorial to transfer private info from 510 to 301?

[skinerd]

skinerd (http://www.dssftp.com/forum/member.php?u=1911)@

Can you make small step by step tutorial to transfer private info from 510 to 301?


Reckon I can, I used winhex, any good hex editor will work tho.

Assuming you have the flash2 from the 510 and the flash from the 301 saved, assuming you have a 301-013 single tsop.

With winhex it's very simple.
Open both files from the receivers in winhex.
In the flash from the 301-013 single, delete lines 003FFF40 through 003FFF90,
then copy and paste those same lines from the 510 into the 301 flash.

That's it...really.


I tried the same thing in reverse, that is going from the 301 to the 510, but all I got was blank video, got previews fine, but all other channels blank. So I missed something there, but I had done the 510 to 301 before so I knew it would work.

[skinerd]

if you have a subbed married rom 102 image for any receiver it contains all data necessary for private numbers using those numbers between married rom and receiver. however if it is a SK receiver it will work for those only. it will not work for dt08 receivers without some modification.

I have not tried it yet, but I'll bet I can put SKs in a 301-010 and make it work with a married 510 card bin. Only other non SK receiver I have available is a 3900, so I may try that too. I have not done this yet, but am reasonably sure it will work.

[rg6a]

if you have a subbed married rom 102 image for any receiver it contains all data necessary for private numbers using those numbers between married rom and receiver. however if it is a SK receiver it will work for those only. it will not work for dt08 receivers without some modification.

I'm not attempting to HiJack this <T>hread but have a question that sort of pertains to it.

I have three D*sh irds , two of which go back to the N1 days (Mdl. 1000, 3000) and also a 2700 that I purchased off *bay with a SOx card for $37. Now is the ird data what you guys call 'private'?

I was thinking of converting the 2700 to the Bitch, but should I save the TSOP info first, as it may come in handy down the road should I wish to convert back?


Thnx in Advance

[skinerd]

I'm not attempting to HiJack this <T>hread but have a question that sort of pertains to it.
I have three D*sh irds , two of which go back to the N1 days (Mdl. 1000, 3000) and also a 2700 that I purchased off *bay with a SOx card for $37. Now is the ird data what you guys call 'private'?
I was thinking of converting the 2700 to the Bitch, but should I save the TSOP info first, as it may come in handy down the road should I wish to convert back?
Thnx in Advance

The best private info comes from a married card/receiver.
You can ganerate your own, based on numbers from the receiver, but true married card/receiver is the best source.

You can throw the 1000 and the 3000 in the trash so they don't take anymore of your space than they are worth.

[otherside]

Hi guy, i have a question that pertains to going private. I have a 2800 I want to go to original tsop and I want to use my cam info on the public codespace image with blocker and tiers that i've been using, will I be able to change the codespace image in GenDTo8 by just changing cam id, zip, and time zone? Thanks

[tommyoz]

I have a question regarding a conversion from Dish 6000 to Bev 6000.

Would it be possible to transfer my private info from a 3100 Bev unit to a 6000 converted from Dish to Bev?

[john smith]

Will this work with a 510 to 301-10? Thanks for any help you can give.

[john smith]

Will this work with a 510 to 301-10? Thanks for any help you can give.


Can some one help with this please i keep getting code 129. I want to use the same card from the 510 to the 301.10 the 510 is a married sub card. And I have read the tsop on the 510 and the 301.10 thank you.