Best way to Run 102

[okwassup]

didnt use ROM 102 since last ECM that killed my card . have open 102 rev 3 and 2 ROm 102 married to thier IRD at Rev 10B .

iam thinking to get back in plastic .

Mikobu unlocker that i changed the ... chip into the Max chip ,cant remember the digits .
so what is the best program out there for reading writting to ROm 102 USING this unlocker reader/writter., and what are the bins to use with blocker, are there good one rom 102 bin and blocker .
peace

[mad max]

For glitching the 10B's you should do some reading before you start. Identify the type of Mik u have and see what settings other peeps have had success at. There is a glitching section here. If you have a newer Mik some have a pot usually cheap and some don't. My Mik N2 I removed the pot and relaced with a 200 ohm resistor. It's not my favorite unlocker but it has come in handy. Another way is find a dealer with a good rep and send them out although it's safer it's not as much fun and you aren't learning, of course if you loop I can't say that's a whole lot of fun either. Rev 10B is a bugger to glitch so remember lot's of research is needed, but there is no magic bullet for you or a dealer lately it seems to be 50/50 so good luck.
As far as your open rev 103 my best advice, others may differ of course is private script and private blocker ie. RP is a good one.

[okwassup]

my Mik dont have a pot , i remember puting a resistor i think was 2.2 K ohm. anyhow iam realy not in a hurry to open those .,i can wait i guess., so you say use the RP script., to be honest i never did anything PVT i always used the public files for my IRD and cards, plastic or none. so what about the program to use with Mik to read write to card ., what you all using or best out there., i flashed it with ND 13.
the script and pvt blocker are all one file or several and need to patch., and th IRD bx ...etc the same as the public atmega No RSA .

[Crazy1_79]

i use n2edit to read and write with a unlocker. flash with newdrs and off you go.

[hacker]

Just find any blocker that doesn't pass B1 and you should be fine.

[Crazy1_79]

anyone try that new codespace yet?

[Dnk]

Rgr Crazy I have an extra 102 (@103 non the less smile) so I thought I would test it. It is running well and in fact did roll, so far so good lets see how long it lasts. BTW still on older firmware (301.10 I havent tried it in my 510 yet)

[smoky44ca]

depending on a intercept installed, i would be using nagraedit 2.58 for reading and writing. if you dont need those 10B's right now i would hold off on trying to glitch into them. tricky rev.

[foxx1600]

runnin the new v15 codespace now workin good for me sofar rolls great .. never lost a card to codespace blockers.. if yer low on plastic then use non roll blocker.

[cingulum]

runnin the new v15 codespace now workin good for me sofar rolls great .. never lost a card to codespace blockers.. if yer low on plastic then use non roll blocker. Are you also running private numbers?

[rafiqi]

Where do you find the password for nagraedit2.58?

[rafiqi]

where do you find the password for unlocking in Nagraedit 2.58?
Thanks

[old school]

anyone try that new codespace yet?

Also using the codespace 15 blocker with AR. Working for me!

[okwassup]

no iam not running anything with pvt numbers ., i was running public last year or so., so now i have to start all over with plastic., so nd 13 is no good ., ok let me look for the newdrs and take it from there., .
however iam still not clear on the bins blocker to write to card., no one mentioned which ones i should use., ofcourse as of now my IRD has public bx...etc

[okwassup]

so thats all in one .?? bin blocker...etc.just write to card.??
i flashed my unlocker with the Newdrs ., and tryed to read my 102 using N2edit 2.55 and its working well.
so its all in one.?
peace

[okwassup]

anther dorky question ., key graber and key updater dont work., so how can i update manualy the keys in the dish bin.,
with key updater its not doing it manualy .
how its done guys.
peace

[2getwired]

Mr. Tierworks:)

[bmellow]

Where do you find the password for nagraedit2.58?


what do you mean>. To lock your script?/ It depends on the script. Sometimes it is at line 9878, some are in the 9600's. you may have to read all the readme files or just look through the script manually for the password.

[Crazy1_79]

the password is in the blocker patch usually near the top for easing changing

[okwassup]

ok guys an update i used negra master to input the keys and write to card ., and it worked but not sure if iam protected., as i was told i used Jamesbond file . thats all., i didnt patch anything else.
so tierworks would be easier to work with.??

[cingulum]

ok guys an update i used negra master to input the keys and write to card ., and it worked but not sure if iam protected., as i was told i used Jamesbond file . thats all., i didnt patch anything else.
so tierworks would be easier to work with.??Should have patched a blocker to bin